I need to upgrade to firewall which supports Active/Standby configuration.I am currently using a ASA-5510,SSM-20 8.2(5).Will the configuration file from the ASA-5510 work on the 5515X?
View 1 RepliesMy customer has a rather complex configuration on an ASA 5510 running version 8.2.
They are migrating to new ASA 5515X models which of course only version support 8.6
How can i convert the configuration from 8.2 to 8.6 since the new ASA's do not support the earlier versions?
The X series seems to be a great option for new deployments but what about replacements of existing older models?
if there is a way to configure pim-ssm on asa 5585x-ssm20.
View 1 Replies View RelatedI will be implementing a new firewall (cisco asa 5515x) on my existing 3750x (server switches) and my 2960s (user switches). What should I need to apply on my firewall and swtiches to make the implementation successfull. I will put my 3750x as my DMZ and my 2960s as my inside. The 3750x have multiple subnet and also the 2960s.which features and technologies i need to know on those 3 products. my 3750x and 2960s don't have any ACL defined and most common features are vlan, switchport, trunking, spanning-tree, stacking, vtp.how my asa knows that my 3750x/2960s have multiple vlans. my current connection right now on 3750x and 2960s is just through 6 ports i assigned as one trunk, below is my config [code]
my 2960s vlans are almost the same with my 3750x except vlan 160, 170, 192. but of course when i put this in asa, i have to segragate vlan for 3750x (192, 100, 110,160, 170) and 2960s (130, 150). for my 2960s connection to the asa and since this will have big bandwidth, i will use 3 ports on my asa (and trunk it) connecting to my 2960s and i will use 2 ports on my asa (and trunk it) connecting to my 3750x. the one internet ports and my one management ports on my asa will stay like that.
I have a strange issue which happened to me last weekend with two ASA 5515X on version 8.6(1)2. There was a planned power shutdown which only affected the primary firewall. Failover was configured and running successfully. The configuration was also saved after every change made. After power was shut and primary firewall went off the secondary took over like it should but unfortunately all configuration was gone. We immediately powered on the primary again but also this one lost the configuration.
While reconfiguring the firewall we ran into another problem. The devices won't pair although it was the correct configuration. After three times removing and adding the same failover configuration the devices accepted the failover and worked together again.
I went through the bug toolkit and white papers regarding ASA 5515x and this particular version but were not able to find anything.
I am in a process of replacing the Cisco ASA 5510 with 7.3 OS with a new Cisco ASA 5515X with 8.6OS. In the existing Cisco ASA 5510, we have configured 'no nat-control' for which the traffic from all sub-interfaces were flowing to the lower security interfaces without any NAT command. Just access-lists were configured. Now how do i acheive the same in the Cisco ASA 5515X with 8.6? I do not find any 'no nat-control' command available for it.
View 3 Replies View RelatedWhat is the maximum number of contexts a pair of 5515Xs in HA mode can support?
I know each 5515X can have a max of 5 contexts, but does that mean in HA mode a pair can support 10 with license pooling?
I'm using ASA 5515X my concern is I was not able to block the traffic of P2P such as BitTorrent etc. I was also view some technotes on how to use webfilter without using Websense or Smartfilter tools and lucky I'm able to block certain websites. how to block the traffic of P2P?
View 2 Replies View RelatedI have ASA 5515x and it has already Internet Connection since my firewall is not "production". So right now I'm trying to configure a Remote Session just for a test and eventually I was not able to connect from it. I followed the instructions from technotes but still Remote Connection dropped. Here's my sample configuration on my firewall, btw I also configured a service policy rule and ACL just to make sure if I can able to access the Server inside my network but Session also dropped.
nat (inside,outside) source static 1.1.1.1 2.2.2.1
access-list 110 extended permit tcp host 3.3.3.1 host 2.2.2.1 eq 3389
CiscoASA(config)#class-map rdpmss
[Code].....
I have a misanderstand about management interface configuration in cluster. So I have a cluster asa 5515X with management interface. i Would like to be able to connect to any of the member of my cluster on management interface, so i would like to fix a different ip on management interface on each of my node ip 92 and 91. I think it is the only way to make asa firmware update to access local flash on each node.
my config
interface GigabitEthernet0/1
channel-group 1 mode active
no nameif
[Code].....
Is it possible to upgrade directly from 8.0(4) to 8.2(5) software in 5510. Is there be any workaround in regards to the config.
View 3 Replies View Related1-Can I do this upgrade directly? i have single ASA 5510 running 8.0.4, i want to upgrade it to 8.2.1, is it as simple as copying IOS and setting boot sequence?
2-I am copying IOS 8.2.1 from my another 5520 ASA, and installing it on 5510 ASA, will it cause any issues? just checking if there is any secret keys involved that can cause issue? (As far hardware req is concerned i have checked my both ASA matches Memory/Flash requirements)
Can I upgrade ASA from "disk0:/asa708-k8.bin" & asdm-508.bin directly to asa825-33-k8 and asdm-712 ?
What is the proceedure if i go from 7 to 8 ? For me what will be the suggested upgrade from asa708-k8.bin & asdm-508.bin ??
im new to cisco asa and the model is 5515x with license plus. below is my config at home,
ciscoasa#
ciscoasa# sh run
: Saved
[Code]......
I have a problem trying to connect a VPN site to site between a FWASA 5515X - ASA5510. [code] The configuration in the 5510 its the old one that i been using with a firewall 5505.
View 1 Replies View RelatedI am using Cisco ASA5510 Firewall in my network. The IOS is Software Version 8.0(5)24. The Flash is 512 MB and DRAM 1GB on the ASA. I want to upgrade the IOS on my Firewall and use the Latest one.
Also, what are the IOS details for upgradation. The Firewall is serving both the VPN and FW Rules.
I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license (ASA5500-SSL-250) for the standby unit.
View 3 Replies View RelatedI am trying to find out the best path to upgrade to two ASA 5510 running 9.0 (1). I know there are changes in the new version. Let me know what information you need and i will post.
View 2 Replies View RelatedHow to upgrade cisco asa 5510 from 8.0(4) to latest ios. Update latest one and step to upgrade. also need to update IPS firmware also because this device together with IPS.
View 9 Replies View RelatedOne of my clients has an ASA 5510 running version 7.0(8) and ASDM 5.0(8). My question, to what versions of each software can I update the appliance to? Additionally, must I upgrade incrementally? i.e from 7.0 to 7.1 then to 7.2? I did find this article ,URL,That states you must go from 5.0 to 5.1 to 5.2, but 5.1 and 5.2 do not appear to be on the download page. The earliest release I could find was 6.2. Can I update the ASA version all the way up to v8 and then update ASDM? Also, noob question, updating the software doesn't erase any of the configurations does it? This is a live firewall and downtime for reconfiguration isn't much of an option.
View 7 Replies View Relatedwe recently upgraded our ASA 5510 active/standby cluster from ASA Version 8.3.2 to 8.4.1(11). Unfortunately the standby ASA is now crashing a few seconds after the configuration was synchronized from the active ASA.
Also completely disabling HA, bringing the default config to standby ASA again and activating HA afterwards did not work. Also tried through the Wizard provided by ASDM to be sure to have no errors with requirements.
How to solve this without doing a downgrade back to 8.3.2. ?
I have a customer who is going to host a VOICE services like providing SIP services to its customers. What specific ports required to be opened up for this on ASA 5515X. I would rate it ASAP.
View 3 Replies View RelatedI need to know if the cisco ASA next generation specially ASA 5515X support PBR or no ?how to implement it? Also if i have many internet connections and i need to dedicate 2 ISP’s ADSL internet lines to certain service (such as mail) if the 1st fail, so the 2nd line come up to make redundancy with it ----------- Is this available on cisco ASA next generation.
View 1 Replies View RelatedI have a FWSM cluster that I exceeded the maximum number of static nat entries on. i migrated the connectivity off to a pair of PIX 535's that seem to be handling the adderess translation needs. however the number of NAT entries being required is increasing and being the PIX series wal EOL'd several years back..I need to replace them.. The static 1-1 nat entries cannot be summarized into network as the hosts that are being nat'd are scattered all over various micro subnets in the all 3 rfc1918 ipv4 address ranges and they are being manged directly by snmp and SNMP-trap and other services that prohibit the use of many-to-one nat. Is there a mknown maximum number of static 1-1 nat entries that can be defined on the ASA 5515-x, 5525=x and higher ASA firewalls? Say I wanted to be able to grow to 2500 or more static 1-1 nat entries. I am currently running 2010 1-1 static host nats currently.
View 1 Replies View RelatedIm upgrading a asa 5510 from 8.3 to 8.4.
I know from 8.2 to 8.3 was not a mirror update because of nat and access-list but is from 8.3 to 8.4 a mirror update or is there anything which I should be aware of?
We want to run ASA 8.4.x on an old ASA5540. We need to upgrade its memory to 2 GB with the following memory upgrade: ASA5540-MEM-2GB=
I suspect that we will completely remove the existing 1 GB of memory and replace it with 2 GB. If this is the case, can I use this 1 GB of memory removed from the ASA5540 and put it in a ASA5510 instead of buying a ASA5510-MEM-1GB= for the ASA5510?
I am looking to upgrade a 5510 that is currently on code version 8.0(4) to code version 9.1. I know I will have to upgrade to 1gb ram, but can i just upgrade straight to version 9.1 or do I need to follow an upgrade path? This is a standalone device so I am planning on downtime.
View 8 Replies View RelatedIs it required for the 3des license upgrade for the asa5510 to reboot for the further configuration of site2site tunnels.
View 1 Replies View RelatedAfter I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and the protocol is up, when I type: show interface.But when I ping the interface from a computer connectet to the interface, nothing happens.
Even the logging shows nothing.
I need to upgrade the active/standby failover pair of 5510 ASA's to have1 Gig DRAM each, and I am trying to plan out the upgrade process. I'm looking for a zero downtime upgrade process.
I know that the failover pair has to have the same amount of memory, so how do I perform a zero-downtime upgrade process?Can I power off the standby unit and upgrade it's memory first? Or will it cause a memory mismatch between the active and standby units when it is powered on?
i am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedI am upgrading an ASA 5510 from ASA822-k8 to ASA841-k8. I know I have to upgrade the RAM to 1GB from 256MB, but was wondering if it is a direct upgrade, or do I have to step through some of the 8.3(x) versions?
View 2 Replies View RelatedI want to upgrade my ASA 5510 from version 7.0(6) to 8.2(5). Reading the release notes for 8.2(5) it says the DRAM requirement is 256MB unless you have high CPU usage. Also it says I need to upgrade through the major releases, from 7.0(x) to 7.1(x) and 7.1(x) to 7.2(x) and then from 7.2(x) to 8.2(x). The questions are:
- My ASA has 256MB of RAM and 68% of free memory, would you think it will run the 8.2(5) version with no problem?
- When making the upgrades to the major releases, is there any consideration regarding the configuration file? Or the versions to use for the 7.1 and 7.2 versions?
- Would you recommend making all the upgrades in one maintenance window? How much time could it take?