I am looking to upgrade a 5510 that is currently on code version 8.0(4) to code version 9.1. I know I will have to upgrade to 1gb ram, but can i just upgrade straight to version 9.1 or do I need to follow an upgrade path? This is a standalone device so I am planning on downtime.
View 8 Repliesi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View Relatedprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View RelatedI Have an asa 5510 running code 7.2 configured with ssl vpn,ssl vpn users able to connect to to portal which i have configured with the required resources,but the thing is that these ssl users unable to upload files to cifs shared directory , although they have full access to the shared folder
View 0 Replies View RelatedI just need to upgrade existing FWSM of 6509.FWSM Firewall Version 2.3(1)is it possible to upgrade to the version of 4.X .If not to which version is safe?And also I need to steps of doing FWSM upgrade.
View 1 Replies View Related I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?
what the upgrade path is for 5505 ASA . I have one which is version 7.2 and need to upgrade it to 8.4(5). I have read that it needs to upgraded btwn major release versions.Not sure if I need to upgrade from 7.2 - 8.0 , then form 8.0 - 8.2, then from 8.2 - 8.3 and finally 8.3 to 8.4 or can I just upgrade from 7.2 - 8.2 and then from 8.2 - 8.4 .Also what is the minimum memory requirements for vers 8.4 .my ASA running on vers 7.2 currently has 256Mb Memory and I will be upgrading this to 512MB before I do the upgrade the image above?
View 4 Replies View RelatedI'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
View 3 Replies View RelatedI have a ASA5550, with a IOS version 8.2(5).
I would like to upgarde to the latest version, and I believe it is 9.1.1.
Will give configuration of NAT for my internal users with 192.168.1.0/24 with single public IP.
I new to configure IOS version 8.3.
i have asa901-k8.bin" in my asa firewall and downlaod liecnce from cisco,now i dont know how to allow internet to my user.?
View 1 Replies View Relatedhave a question. I have a ASA5510 with IOS version 8.2 . I have my firewall and behind it also have a mail server eg 192.168.1.x. When i send email from inside network it doesn't show as if it's coming grom the out side nated public IP of my server but IP of firewall. What am i missing my example nat statements are . Nat-control is disabled.
static (inside,outside) 196.68.99.x 192.168.1.x netmask 255.255.255.255
access-list inbound extended permit tcp any host 196.68.99.x eq 225
accesslist outbound extended permit host 192.168.1.x host 196.68.99.x
I have an access-list that was named "extended" (without quotation marks) and the ASA will not let me remove it.
I have tried everything I know to try and get it out, but I cannot remove a single line.
ASA(config)# no access-list extended line 1 extended permit ip host 10.1.1.1 host 192.168.1.1ERROR:<1> not a valid permission
ASA(config)# no access-list extended line 1 permit ip host 10.1.1.1 host 192.168.1.1ERROR:<1> not a valid permission
I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
View 4 Replies View RelatedJust purchased a 2504 w/15 licenses and to run 10 - 2602i AP's. Code out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code versions say ED, which I thought was not final release versions.
View 1 Replies View RelatedI see several code versions that seem to support on ACE30.Is A2.3.4 Or A2(3.5) that latest version for ACE20-MOD-9?Will the version 4 or 5 run on ACE20?I currently user A2(3).
View 3 Replies View RelatedI am looking upgrade my ASR routers to a newer code. I am running asr1000rp1-advipservicesk9.03.03.01.S.151-2.S1.bin now. Would like input on what a good stable version is. I am not bleeding edge so the latest version I won't trust.
View 5 Replies View RelatedIs it possible to upgrade directly from 8.0(4) to 8.2(5) software in 5510. Is there be any workaround in regards to the config.
View 3 Replies View Related1-Can I do this upgrade directly? i have single ASA 5510 running 8.0.4, i want to upgrade it to 8.2.1, is it as simple as copying IOS and setting boot sequence?
2-I am copying IOS 8.2.1 from my another 5520 ASA, and installing it on 5510 ASA, will it cause any issues? just checking if there is any secret keys involved that can cause issue? (As far hardware req is concerned i have checked my both ASA matches Memory/Flash requirements)
Can I upgrade ASA from "disk0:/asa708-k8.bin" & asdm-508.bin directly to asa825-33-k8 and asdm-712 ?
What is the proceedure if i go from 7 to 8 ? For me what will be the suggested upgrade from asa708-k8.bin & asdm-508.bin ??
give me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies View RelatedI am using Cisco ASA5510 Firewall in my network. The IOS is Software Version 8.0(5)24. The Flash is 512 MB and DRAM 1GB on the ASA. I want to upgrade the IOS on my Firewall and use the Latest one.
Also, what are the IOS details for upgradation. The Firewall is serving both the VPN and FW Rules.
I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license (ASA5500-SSL-250) for the standby unit.
View 3 Replies View RelatedI am trying to find out the best path to upgrade to two ASA 5510 running 9.0 (1). I know there are changes in the new version. Let me know what information you need and i will post.
View 2 Replies View RelatedHow to upgrade cisco asa 5510 from 8.0(4) to latest ios. Update latest one and step to upgrade. also need to update IPS firmware also because this device together with IPS.
View 9 Replies View RelatedOne of my clients has an ASA 5510 running version 7.0(8) and ASDM 5.0(8). My question, to what versions of each software can I update the appliance to? Additionally, must I upgrade incrementally? i.e from 7.0 to 7.1 then to 7.2? I did find this article ,URL,That states you must go from 5.0 to 5.1 to 5.2, but 5.1 and 5.2 do not appear to be on the download page. The earliest release I could find was 6.2. Can I update the ASA version all the way up to v8 and then update ASDM? Also, noob question, updating the software doesn't erase any of the configurations does it? This is a live firewall and downtime for reconfiguration isn't much of an option.
View 7 Replies View Relatedwe recently upgraded our ASA 5510 active/standby cluster from ASA Version 8.3.2 to 8.4.1(11). Unfortunately the standby ASA is now crashing a few seconds after the configuration was synchronized from the active ASA.
Also completely disabling HA, bringing the default config to standby ASA again and activating HA afterwards did not work. Also tried through the Wizard provided by ASDM to be sure to have no errors with requirements.
How to solve this without doing a downgrade back to 8.3.2. ?
Im upgrading a asa 5510 from 8.3 to 8.4.
I know from 8.2 to 8.3 was not a mirror update because of nat and access-list but is from 8.3 to 8.4 a mirror update or is there anything which I should be aware of?
I need to upgrade to firewall which supports Active/Standby configuration.I am currently using a ASA-5510,SSM-20 8.2(5).Will the configuration file from the ASA-5510 work on the 5515X?
View 1 Replies View RelatedWe want to run ASA 8.4.x on an old ASA5540. We need to upgrade its memory to 2 GB with the following memory upgrade: ASA5540-MEM-2GB=
I suspect that we will completely remove the existing 1 GB of memory and replace it with 2 GB. If this is the case, can I use this 1 GB of memory removed from the ASA5540 and put it in a ASA5510 instead of buying a ASA5510-MEM-1GB= for the ASA5510?
Is it required for the 3des license upgrade for the asa5510 to reboot for the further configuration of site2site tunnels.
View 1 Replies View RelatedAfter I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and the protocol is up, when I type: show interface.But when I ping the interface from a computer connectet to the interface, nothing happens.
Even the logging shows nothing.
I need to upgrade the active/standby failover pair of 5510 ASA's to have1 Gig DRAM each, and I am trying to plan out the upgrade process. I'm looking for a zero downtime upgrade process.
I know that the failover pair has to have the same amount of memory, so how do I perform a zero-downtime upgrade process?Can I power off the standby unit and upgrade it's memory first? Or will it cause a memory mismatch between the active and standby units when it is powered on?