I'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
View 3 RepliesI have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies View Relatedprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedI just need to upgrade existing FWSM of 6509.FWSM Firewall Version 2.3(1)is it possible to upgrade to the version of 4.X .If not to which version is safe?And also I need to steps of doing FWSM upgrade.
View 1 Replies View Relatedwhat the upgrade path is for 5505 ASA . I have one which is version 7.2 and need to upgrade it to 8.4(5). I have read that it needs to upgraded btwn major release versions.Not sure if I need to upgrade from 7.2 - 8.0 , then form 8.0 - 8.2, then from 8.2 - 8.3 and finally 8.3 to 8.4 or can I just upgrade from 7.2 - 8.2 and then from 8.2 - 8.4 .Also what is the minimum memory requirements for vers 8.4 .my ASA running on vers 7.2 currently has 256Mb Memory and I will be upgrading this to 512MB before I do the upgrade the image above?
View 4 Replies View RelatedI am looking to upgrade a 5510 that is currently on code version 8.0(4) to code version 9.1. I know I will have to upgrade to 1gb ram, but can i just upgrade straight to version 9.1 or do I need to follow an upgrade path? This is a standalone device so I am planning on downtime.
View 8 Replies View RelatedI have a ASA5550, with a IOS version 8.2(5).
I would like to upgarde to the latest version, and I believe it is 9.1.1.
How to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies View RelatedThere is a PIX 506E and ASA5510, with different connection to service provider. Problem is Apple remote users can't access resources protected by the PIX506E. Apple users can access resources protected by ASA5510. Physically the PIX and ASA are in close proximity with no physical connections. Is it possible for Apple users to authenticate with the ASA and the traffic get routed to and get authenticated by the PIX, inorder to access resources?Due to bandwidth restrictions, a DMZ on the ASA will not be created at this time inorder to consolodate firewalls. Currently 2 x T1 is the connection between ASA and ISP; 1 T1 connects PIX to ISP.
View 1 Replies View RelatedSo i got a Cisco PIX 506e from a friend and want to set it up for a VPN. Though i cant download the PDM (PIX Device Manager) since i dont have a Contract or something like that. So i cant set it up.
View 1 Replies View RelatedI need to replace an ageing PIX 506e with an ASA 5505.The current setup looks like this: The PIX is used for site-to-site VPN connection via the WAN 2 link. The WAN 1 link is used for general Internet connectivity.I don't have access to the Draytek Router as it is supported by a 3rd party, but I believe it uses static routing to direct the relevant traffic to/from the PIX.
When I replace the PIX with the ASA, the inside i/f connection experiences dropouts - but no errors show in the logs.The only significant difference I can see in the config is that the ASA utilises VLans for the inside & outside interface configs - I used the PIX-to-ASA Migration tool to make the initial configuration on the ASA.In tests, if I only connect the inside i/f of the ASA, pings from the LAN are stable. Once I connect the outside i/f, pings timeout approx 80% of the time.
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
View 4 Replies View RelatedI am trying to add a username to the local database for remote VPN connection but always i get this error when I add,Encrypted password is of incorrect lengthUsername addition failed.
View 1 Replies View RelatedI just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
View 4 Replies View RelatedWhat is the easiest way to restore my config? I backed it up yesterday with my tftp server. Today I made some changes and messed some things up and need to restore the config from yesterday.
View 1 Replies View RelatedI have a problem with PIX 506E that meets the version 6.1, and in an simple computer network equipment seems to behave in strange ways because some web sites do not open or very open slow thereby its operation impracticable. On the other hand other web sites open normally.
Querying the web site of the Cisco, I found several documents discussing the same problem but in a later version ( 7.0 ), not in this version 6.1.
I've tried removing the pix from the network , not the error occurred, again insert pix however tested only with a machine, without the rest of the network and the problem persists
I like to set up a pix and router for this network for a small buss, but I need to know what type of cable do I need to set this connection to work straight through or a cross over cable? also I need a subgestion if a nat would work better on the pix or leave it on the router?
View 4 Replies View RelatedSo I was doing some testing with my BB Playbook where I wanted to see what outside connections it tried to make during startup and whatnot. I have a pix 506e running 6.3(5). I created an simple 'deny ip any any' access list on the inside interface so that the Playbook doesn't actually make any connections, but I set up a 'capture' on the inside interface accepting 'ip any any' to see what kind of traffic I could see heading outbound from the Playbook. Well, it started off showing attempts to query DNS (and failed, naturally), but then after a couple of minutes, it tried to connect to a couple of IPs over port 443 and actually got a response!!! For the life of me, I can't figure out how this can happen. NO traffic should be allowed outbound due to my explicit 'deny' rule, but for some reason some traffic on port 443 made it past the firewall and got a response back. There are no other rules in the access list except the 'deny' rule. My PIX configuration is quite simple and I cannot see anything that would allow the Playbook traffic to circumvent the access list.
I've come to think that either RIM has found away around Cisco access-lists, or there is a bug in the Pix OS. I know it's an old appliance/OS, but still. I wouldn't think it could be THAT easy to bypass the firewall.
I have a C2950 Switch & I am trying to upgrade the IOS version of it so that I can proceed with learning about SSH. My current version of 12.1 does not have Enhanced Imaging. I am so new to Cisco, that I have spent hours trying to find the correct page, or link, or anything that can enable me to upgrade to a later version.
View 6 Replies View RelatedI have installed ACS Windows 2003 R2 Services Pack 2.
I am upgrading of version 4.1.1.23 to version 4.2.1.15. Recommended by Cisco.
Before of update everthing works fine.
After of upgrade, this does not authenticate user, sends the next message "External user not found", "Authentication session invalidated" and "internal error".
The mapping is ready. annex image.
I want to upgrade my Cisco ACS Engine appliance 1120 from software version 3.3 to the latest version (5.x). How do I go about this?
View 2 Replies View RelatedI have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies View RelatedI have 4 switches of 3750. I need toupgrade all the switches, but I can't to disconnect the stack cable.How I can to upgrade the version without to disconnect the stack cable?
View 2 Replies View RelatedWe have five cisco WLC 5508 and one WCS .The WLC is running on 7.0.116.0 version at present but we want to upgrade it to 7.4.100.0 but on cisco site at download location , the below thing is mentioned...
WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time
Access Point Model----Cisco 3501i Series
So i want to know, can i upgrade it to this version when we are having the WCS in our network ?
I would like to upgrade our three WLC 4402 controllers from version 7.0.116.0 to 7.0.235.3. I have downloaded the two files (AIR-WLC4400-K9-7-0-235-3-ER.aes and AIR-WLC4400-K9-7-0-235-3.aes). Which one should I upgrade/install first?
View 4 Replies View RelatedI want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies View RelatedI just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View Relatedhow can i upgrade to Mini IOS Version 7.3.1.73 on the AIR-CAP 3502I. we some that have Mini IOS Version 7.3.1.73 and some that have Mini IOS Version 7.0.112.74. want them all the same.
View 1 Replies View RelatedWe just purchased the following items:
(1) R-PI-1.1-500-K9
(2) PRIME-NCS-APL-K9
I want to know how I can upgrade to the latest version of Cisco Prime Infrastructure.
I have this 4900M running version 12.2(54)SG1. I the log I get this 3 lines:
May 8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May 8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry: Sw entry:
May 8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ". I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.
We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
What is the latest version to upgrade the WLC?
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
How do I upgrade the boot rom version on the 7200 router? I am running IOS Version 12.4(22)T and when I plug in the serial ds3 card in my router it keeps rebooting with a watch dog error ( see below). Also, what version should I upgrade to?
Router#sh verCisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Fri 10-Oct-08 10:10 by prod_rel_team
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 0 minutesSystem returned to ROM by power-onSystem image file is "sup-slot0:/c7200-spservicesk9-mz.124-22.T.bin"
[code]....