I am trying to add a username to the local database for remote VPN connection but always i get this error when I add,Encrypted password is of incorrect lengthUsername addition failed.
View 1 RepliesI have a customer that has a FWSM on a 6500, I want to create a read only account for them, i believe user privelage of lvl_3 When I log into the firewall it prompts me for a password straight away.
Is there a way that i can create a login that when it prompts me for a password, I can have a password setup to put into that prompt to get a certain level of access, instead of the standard lvl_15 access
How to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies View RelatedThere is a PIX 506E and ASA5510, with different connection to service provider. Problem is Apple remote users can't access resources protected by the PIX506E. Apple users can access resources protected by ASA5510. Physically the PIX and ASA are in close proximity with no physical connections. Is it possible for Apple users to authenticate with the ASA and the traffic get routed to and get authenticated by the PIX, inorder to access resources?Due to bandwidth restrictions, a DMZ on the ASA will not be created at this time inorder to consolodate firewalls. Currently 2 x T1 is the connection between ASA and ISP; 1 T1 connects PIX to ISP.
View 1 Replies View RelatedI have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies View RelatedSo i got a Cisco PIX 506e from a friend and want to set it up for a VPN. Though i cant download the PDM (PIX Device Manager) since i dont have a Contract or something like that. So i cant set it up.
View 1 Replies View RelatedI need to replace an ageing PIX 506e with an ASA 5505.The current setup looks like this: The PIX is used for site-to-site VPN connection via the WAN 2 link. The WAN 1 link is used for general Internet connectivity.I don't have access to the Draytek Router as it is supported by a 3rd party, but I believe it uses static routing to direct the relevant traffic to/from the PIX.
When I replace the PIX with the ASA, the inside i/f connection experiences dropouts - but no errors show in the logs.The only significant difference I can see in the config is that the ASA utilises VLans for the inside & outside interface configs - I used the PIX-to-ASA Migration tool to make the initial configuration on the ASA.In tests, if I only connect the inside i/f of the ASA, pings from the LAN are stable. Once I connect the outside i/f, pings timeout approx 80% of the time.
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
View 4 Replies View RelatedI just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
View 4 Replies View RelatedWhat is the easiest way to restore my config? I backed it up yesterday with my tftp server. Today I made some changes and messed some things up and need to restore the config from yesterday.
View 1 Replies View RelatedI'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
View 3 Replies View RelatedI have a problem with PIX 506E that meets the version 6.1, and in an simple computer network equipment seems to behave in strange ways because some web sites do not open or very open slow thereby its operation impracticable. On the other hand other web sites open normally.
Querying the web site of the Cisco, I found several documents discussing the same problem but in a later version ( 7.0 ), not in this version 6.1.
I've tried removing the pix from the network , not the error occurred, again insert pix however tested only with a machine, without the rest of the network and the problem persists
I like to set up a pix and router for this network for a small buss, but I need to know what type of cable do I need to set this connection to work straight through or a cross over cable? also I need a subgestion if a nat would work better on the pix or leave it on the router?
View 4 Replies View RelatedSo I was doing some testing with my BB Playbook where I wanted to see what outside connections it tried to make during startup and whatnot. I have a pix 506e running 6.3(5). I created an simple 'deny ip any any' access list on the inside interface so that the Playbook doesn't actually make any connections, but I set up a 'capture' on the inside interface accepting 'ip any any' to see what kind of traffic I could see heading outbound from the Playbook. Well, it started off showing attempts to query DNS (and failed, naturally), but then after a couple of minutes, it tried to connect to a couple of IPs over port 443 and actually got a response!!! For the life of me, I can't figure out how this can happen. NO traffic should be allowed outbound due to my explicit 'deny' rule, but for some reason some traffic on port 443 made it past the firewall and got a response back. There are no other rules in the access list except the 'deny' rule. My PIX configuration is quite simple and I cannot see anything that would allow the Playbook traffic to circumvent the access list.
I've come to think that either RIM has found away around Cisco access-lists, or there is a bug in the Pix OS. I know it's an old appliance/OS, but still. I wouldn't think it could be THAT easy to bypass the firewall.
When I try and add my 2 500x devices to cisco Network Assistant, i receive the following error: Unsopported Device type: UnKnownCannot add device <IP> to community>
Is this a version issues, or setting issue?
I am adding another ISP (and plan to use BGP). I am looking at having two 2811's with one connected to each ISP, or a single 2811 (with an additional HWIC) connected to both ISPs. I am not sure if there is a best practices or an ideal configuration for this.
Currently I have:
ASA5510 ---> 2811 ---> ISP_A
Should I purchase another 2811 for ISP_B and connect it to an available port on the ASA? Or should I just purchase a HWIC-1FE and add ISP_B to the existing router?
I see some advantages to both, but not sure the best way to go. Of course, I could be looking at this wrong and if I plan on buying another router then maybe I should use HSRP and both routers should connect to both ISPs.
I am having trouble adding a computer to the Domain Controller. I have a cable modem running into a di-524 router. The router has DHCP and DNS relay disabled. I set the LAN IP Address of the router to 192.168.2.1. The router is connected to a switch with 10 pc's and a server running 2003. The server has an IP Address of 192.168.2.2. I setup a DHCP server inside 2003 with a scope of 192.168.2.100-192.168.2.199. Under scope options the router is set to 192.168.2.1 and DNS Servers is set to 192.168.2.2 (the ip address of the domain controller). When I try to add the computer it cannot contact the domain controller. Is there something wrong with my DHCP config or DNS?
View 3 Replies View RelatedCustomers ASA 5510 and they are using the default "pix" login. I can log into the command line with pix just fine. I created a user account, call it:username jsmith password Passw0rd priv 15,I'm unable to log into the command line with jsmith. I can get into ASDM with it.
View 6 Replies View RelatedTwo 5520 firewall configuration of the failover and SSH, the first remote landing SSH, can use user and password successful landing, again landing, to prompt the user name password is invalid, what is the reason?
View 4 Replies View RelatedI am trying to configure an ASA 5505 with a username and password. I set all the pass words: [code]
When I reload the device it prompts me for the username, then the password and it fails and just asks for the username again. I have even tried to delete the username / password combo but it still prompts me for it. When I do password recovery the confreg is 0x00000001.
I have a Belkin Play N600 as my primary and have an older Belkin G+MiMO that I'd like to connect as an access point only. Any step by step instructions of how to accomplish this?
View 1 Replies View RelatedI have a ASA 5520 which is intended to use as a VPN for clients using PDA, I think the PDA is a very old product that the VPN only support CHAP/ MS- CHAP, but seems it cannot connect the VPN, it will prompt "invalid username and password" (but in fact the username and password is valid when using PAP), below is the log i captured from the ASDM when the PDA is connecting the VPN. when i tried to connect it in windows PC, I also have the same issue if the VPN setting is using MS-CHAP, if I choose PAP, it can connect with no problem. But the PDA has no option of PAP. [code]
View 0 Replies View RelatedThe ASA 5510 is working with asa8.3.1 and asdm 6.3.1. ( with factory default config )i ve upgraded to asa8.4.1 and asdm 6.4.1.Now the asdm launcher is frozen after username/password. The asdm upload the software and write that "software update completed".After it the hour glass or sand-glass is visible over the asdm window.
View 2 Replies View RelatedI completed the PIX 515 to ASA 5505 migration today with no problems - ok one problem with the logon for ASDM. I'm trying no username and password - then using username and password from the 515 Pix with no success. How to reset the username and password for the ASDM GUI website.
View 3 Replies View RelatedI have just installed and configured a new RVS4000 with VPN (currently running firmware V2.0.0.3), and have enabled the DHCP Server service. I wanted to be able to distribute a search domain in addition to the IP address and DNS Server information (as I have done with other devices that include a DHCP Server), but cannot seem to locate where or how I might do that with the RVS4000.
View 4 Replies View RelatedI have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
it is possible to enable Xauth on pix. I have read multiple threads about using the following cmds:
username test123password testing privilege 2
aaa-server LOCAL protocol local
crypto map mycrypto client authentication LOCAL
However the f/w wont let me add the crypto map cmd, just comes back with the following:
PIX(config)# c.rypto map mycryptomap client authenication LOCAL
Usage: [ show ] crypto { ca | dynamic-map | ipsec | isakmp | map | sa } ...
show crypto engine [verify]
[ show | clear ] crypto interface [counters]
I also tried the following, but they dont work and I am not sure if they are meant for Xauth since I was under the impression that it had to be enabled globally.
PIX(config)# vpngroup test authentication-server LOCAL
Protocol "local" is not supported for authentication of remote users of a h/w client
PIX(config)# vpngroup test user-authentication
[code]....
I seem to be having an issue with my PIX configuration. I can ping the VPN client from the the internal network, but can cannot access any resources from the vpn client. [code]
View 4 Replies View RelatedI have 2 firewalls in my network: ASA 5505 and PIX 506E. Both firewalls's internal network is in the 192.168.0.0/24 subnet but their external addresses are different of course. The inside IP for ASA 5505 is 192.168.0.254/24 whereas the PIX is 192.168.0.1/24. I've successfully configured VPN on the ASA 5505. I'm able to VPN to the ASA and can ping / access hosts that have the 192.168.0.254 as their gateways.However, I'm unable to ping/access hosts behind the PIX. What do I need to do in order to allow access to the network behind the PIX after I VPN to the ASA? Also, I'm unable to ping 192.168.0.254 after I VPN to the ASA.
View 5 Replies View RelatedI am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
It is a PIX 506e firewall with PIX v6.3.
I trying to do password reset on a 506e that I got with the current password unknown. I've gone to the Cisco URL for the reset: [code]
I am using the correct bin file as I checked with my pix version. Also I CANNOT ping the firewall from a PCor system on the network, but CAN ping everthing from the PIX.I've tried using interface 1 but no go. Also I've checked the TFTP software (Solarwinds) is running fine and I've unblocked it in XP's firewall.
So I have a Cisco PIX 506e that I've modified a bit, but am quite happy w/ when it comes to performance and configuration (I can actually set up the VPN server w/o too much thought.) I also have a Mikrotik Routerboard 750, I'm no longer using it as my router due to a few config issues I had plus the fact I had to hard code my internet gateway's arp address into the device due to some issues.
What I am wanting to do, which I'm sure is possible and easily accomplished (I just don't have the time right now to try it) is set the routerboard up behind my pix and have it function as an ipv6 router, while the pix handles my ipv4 duties. I've already set up the routerboard w/ an ipv6 tunnel broker when I had it running as my router, I am just curious if it will work in a similar fashion when configured behind an ipv4 device.
I have ASA 5510 with CSC-SSM-10 .ASA 5510 IOS version- 8.4.2 and CSC-SSM-10 IOS version 6.6.1162.Web filtering is working fine with respective to my configuration.From yesterday morning, i was facing issue with the sites like gmail, webmail.After giving credentials like username and password in the web page, the page is not resonding.In troubleshooting process, i removed all the acls, class maps which will direct all the traffic towards the CSC. In this scenario all my mail service sites are opening.If we apply the these ACLs and Class-Maps, only my mail service sites only affecting.
View 1 Replies View Related