I am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
It is a PIX 506e firewall with PIX v6.3.
Our ASA is a 5580 version 8.1(2) and is the L2L VPN peer for a handful of remote offices including a L2L VPN with a vendor who will provide a service for these remote offices. I have two questions/issues:We will need to provide this vendor access to the remote office network(s) only on port 9100 (printing to specific printers at these offices). I know there is an issue with L2L VPNs ability to see each other but if there is a global command allowing all to see each other that would be bad as we have others and don’t want all to see each other.The remote offices are using CIDR 172.20.0.0/16 so each one is assigned for example 172.20.3 the next office is 172.20.4 and so on. For the crypto map access list for this vendor can we use 172.20.0.0/16 or do we need to specify each individual network?
View 3 Replies View RelatedI have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
View 10 Replies View RelatedHow to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies View RelatedI seem to be having an issue with my PIX configuration. I can ping the VPN client from the the internal network, but can cannot access any resources from the vpn client. [code]
View 4 Replies View RelatedI have 2 firewalls in my network: ASA 5505 and PIX 506E. Both firewalls's internal network is in the 192.168.0.0/24 subnet but their external addresses are different of course. The inside IP for ASA 5505 is 192.168.0.254/24 whereas the PIX is 192.168.0.1/24. I've successfully configured VPN on the ASA 5505. I'm able to VPN to the ASA and can ping / access hosts that have the 192.168.0.254 as their gateways.However, I'm unable to ping/access hosts behind the PIX. What do I need to do in order to allow access to the network behind the PIX after I VPN to the ASA? Also, I'm unable to ping 192.168.0.254 after I VPN to the ASA.
View 5 Replies View RelatedI have a problem with PIX 506E that meets the version 6.1, and in an simple computer network equipment seems to behave in strange ways because some web sites do not open or very open slow thereby its operation impracticable. On the other hand other web sites open normally.
Querying the web site of the Cisco, I found several documents discussing the same problem but in a later version ( 7.0 ), not in this version 6.1.
I've tried removing the pix from the network , not the error occurred, again insert pix however tested only with a machine, without the rest of the network and the problem persists
Is there a way to get VPN IP address without giving someone access to the firewall itself? LIke a script you can put on a website?
View 2 Replies View RelatedI have VPN Router (3845) in Head Office and VPN Router (1921) at Branch Office. I have also internet router (1921) which passes through ASA 5520 to internal Network at Head Office. I can give internet connectivity to Head Office Users by giving access in ASA 5520 with following lines: nat (inside) 1 192.168.2.13 255.255.255.255.
I have added line for internet access for Branch Users in following manner in ASA 5520: nat (inside) 1 173.16.33.4 255.255.255.255. My Head Office user can access internet but my branch office user cant access internet. how can i give internet access to my branch office users?
I have recently bought a new XPS 15Z Currently when I surf the internet I am unable to use the browsers ( IE9 or firefox ). I am able to use non-broswer related internet applications like STEAM, MSN or QQ with no issues in terms of speed or stability. But when I use my browsers to surf, I can have periodic moments when I cannot surf the internet, such as IE9 which says that I cannot connect to the internet due to some unknown error. But when I run diagnostics, it says that I do not have any errors. My adapter for my wired is the Atheros AR8151 PCI-E Gigabit Ethernet Controller (NDIS 6.20). I have already contacted my ISP provider who have worked for with all the troubleshooting methods they can over the phone, and I trust that they are doing their best. But now it seems to me that the problem lies in my computer hardware or software and not in my router.
View 3 Replies View RelatedI don'y know why connecting to a router is always so difficult.. Anyway, my win 7 laptop is connecting to the router and I set it up (Reset everything a few times). I also have no connection through Ethernet connection with the router.What do I do? The modem is Cisco DPQ3212 and the router Keebox-w150nr wireless 150 N router.
View 3 Replies View RelatedAfter replacing a Cisco CSS/SSL Accelorator and PIX firewall with an ACE 4710 to do load balancing and SSL encryption behind an ASA firewall we started seeing mangled HTTP requests in the Apache access logs for the servers in the server farm. This is occurring for several different URLs and not just the one above and for multiple web browsers.The ACE load balances to servers running Tomcat 7 with Apache HTTP server v. 2.2.14. A recent ACE software upgrade to A5(2.1) has not fixed the problem.
View 1 Replies View RelatedI have a problem with my Router WRT120N wen I connect to router with wireless are wired it`s not giving me Internet access but the light on the router of Internet is ON if I put the internet cable directed to my computer give me internet.
View 2 Replies View RelatedI have cisco3750 (core), 3550,3548, 2960, HP Procurve 2510 series, Extreme e250 series swiches running in my network. Now all are running by default. How can I deploy rstp here? Or which is the best loopdetection protocol is best here ? I have aroung 40 vlans . (not looking for PVST )
View 9 Replies View RelatedJust finishing up a small install of a 5508 controller and WCS.Approx 30 AP's across 2 buildings.2 WLANS - 1 prod wpa2 and 1 guest which is completely open to internet only.Our security group is asking if there is a way to determine who is accessing the Prod WLAN. Currently it is setup to work with eap and the users AD account which is working well.I noticed under the client tab in WCS that there is a Vendor name and it shows me intel and even RIM when someone with their Blackberry is connected. BUT when we connect via an IPAD it show "unknown" as vendor name. Is there a way to get the IPAD to register under the vendor name ?
View 1 Replies View RelatedWe are doing a study on our public WiFi to identfy client connections based on wireless Vendor. about 40-50% of the clients wireless Vendors are "unknown". Is there a way to update the list of Vendor mac-addresses in WCS?
View 5 Replies View RelatedWe have a 7609 in production network and I am trying to find out the SFP vendor plugged in module WS-X6724-SFP."show inventory raw" gives me the SN but not the vendor name. "show hw-module subslot 1/1" shows The indicated slot/subslot number is empty. Any commands which can show the SFP vendor?
View 1 Replies View RelatedWe have a L2L VPN with a vendor and our outbound traffic (our local network is 192.168.0.0) NATs over one of our public IP addresses x.x.x.164 to their public IP address 128.x.x.x. In the beginning all our traffic was outbound (port 23) to the vendor and now we need to allow inbound from the vendor to specific 192.168 addresses on our network using port 9100. I’m uncertain as to what I should do to allow their inbound traffic to these IP addresses since we are NATing our entire network over one IP address. Note, the .164 public IP is also used to NAT to other vendors we have L2L VPN with. The VPN terminates to our ASA 5580 version 8.2.
View 5 Replies View RelatedI'm using Cisco ACS 3.3 for RADIUS. How to do I make Vendor-Specific attribute available? (Attribute number 26, format: OctetString) The online help makes reference to it, but does not tell you how to make it available.
View 9 Replies View RelatedWhat is the difference between open protocols and vendor specific protocols?
View 1 Replies View RelatedI tried many different things to get the accurate answer for my issue. I wanted to know, will i face any connectivity or looping issue in the network if i connect Broacade SAN switch on a cisco 6500 switch.Also need to know to maintain a DATA DOMAIN which SAN switch is better? Cisco or other vendor.
View 2 Replies View RelatedI have arequirement where in I need to allow only specific vendor made desktops/laptops to be connected to the switch and block the rest. Say I want only the HP made Laptops to be connected on the Network. and block all other vendors. such as dell, ibm etc.
I am having Catalyst 4500 switches in My network. i tried using the mac access list using the permit and deny statement and then mapping the access list to the vlan access map and then filter using the vlan id. But this doesnt work on cat 4500....the same I tested for 2950 switch and it works perfectly. are there any restrictions on 4500 or any extra configuration has to be done.
I’m trying to configure EAP-Fast following the guide [URL].But when I try to download the certificate, I receive the follow message: “Error installing certificate.”At logs I see:
*TransferTask: Sep 27 14:00:09.479: %UPDATE-3-CERT_INST_FAIL: Failed to install Webauth certificate. rc = 1
*TransferTask: Sep 27 14:00:09.479: %SSHPM-3-KEYED_PEM_DECODE_FAILED: Cannot PEM decode private key
- Remembering I’m doing Device Certificate.
My environment is:
WLC 2106 Windows 2003 with AD and CA When I try to use line commands I can’t too.
it is possible to enable Xauth on pix. I have read multiple threads about using the following cmds:
username test123password testing privilege 2
aaa-server LOCAL protocol local
crypto map mycrypto client authentication LOCAL
However the f/w wont let me add the crypto map cmd, just comes back with the following:
PIX(config)# c.rypto map mycryptomap client authenication LOCAL
Usage: [ show ] crypto { ca | dynamic-map | ipsec | isakmp | map | sa } ...
show crypto engine [verify]
[ show | clear ] crypto interface [counters]
I also tried the following, but they dont work and I am not sure if they are meant for Xauth since I was under the impression that it had to be enabled globally.
PIX(config)# vpngroup test authentication-server LOCAL
Protocol "local" is not supported for authentication of remote users of a h/w client
PIX(config)# vpngroup test user-authentication
[code]....
There is a PIX 506E and ASA5510, with different connection to service provider. Problem is Apple remote users can't access resources protected by the PIX506E. Apple users can access resources protected by ASA5510. Physically the PIX and ASA are in close proximity with no physical connections. Is it possible for Apple users to authenticate with the ASA and the traffic get routed to and get authenticated by the PIX, inorder to access resources?Due to bandwidth restrictions, a DMZ on the ASA will not be created at this time inorder to consolodate firewalls. Currently 2 x T1 is the connection between ASA and ISP; 1 T1 connects PIX to ISP.
View 1 Replies View RelatedI have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies View RelatedSo i got a Cisco PIX 506e from a friend and want to set it up for a VPN. Though i cant download the PDM (PIX Device Manager) since i dont have a Contract or something like that. So i cant set it up.
View 1 Replies View RelatedI need to replace an ageing PIX 506e with an ASA 5505.The current setup looks like this: The PIX is used for site-to-site VPN connection via the WAN 2 link. The WAN 1 link is used for general Internet connectivity.I don't have access to the Draytek Router as it is supported by a 3rd party, but I believe it uses static routing to direct the relevant traffic to/from the PIX.
When I replace the PIX with the ASA, the inside i/f connection experiences dropouts - but no errors show in the logs.The only significant difference I can see in the config is that the ASA utilises VLans for the inside & outside interface configs - I used the PIX-to-ASA Migration tool to make the initial configuration on the ASA.In tests, if I only connect the inside i/f of the ASA, pings from the LAN are stable. Once I connect the outside i/f, pings timeout approx 80% of the time.
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
View 4 Replies View RelatedI am trying to add a username to the local database for remote VPN connection but always i get this error when I add,Encrypted password is of incorrect lengthUsername addition failed.
View 1 Replies View RelatedI just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
View 4 Replies View RelatedWhat is the easiest way to restore my config? I backed it up yesterday with my tftp server. Today I made some changes and messed some things up and need to restore the config from yesterday.
View 1 Replies View RelatedI'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
View 3 Replies View Related