Cisco :: WCS 5508 Monitor View Vendor Name
Oct 4, 2011
Just finishing up a small install of a 5508 controller and WCS.Approx 30 AP's across 2 buildings.2 WLANS - 1 prod wpa2 and 1 guest which is completely open to internet only.Our security group is asking if there is a way to determine who is accessing the Prod WLAN. Currently it is setup to work with eap and the users AD account which is working well.I noticed under the client tab in WCS that there is a Vendor name and it shows me intel and even RIM when someone with their Blackberry is connected. BUT when we connect via an IPAD it show "unknown" as vendor name. Is there a way to get the IPAD to register under the vendor name ?
View 1 Replies
ADVERTISEMENT
Jan 6, 2013
I have a Belkin G router F5D7230-4 (firmware version 8.01.07) and am trying to view stats on what is using our connection.We have a very low capacity, rural wireless broadband that our ISP tells us is maxed out all the time, even when we don't appear to be using any devices, so I'd like to view the traffic on our DHCP client list to see which device is using an excessive amount of bandwith and put a limit on its access.I don't see a statistics tab on the setup page, is there another place to look or does Belkin have an external program to do this?
View 1 Replies
View Related
Nov 17, 2011
Need implementation of an OID to view the number of connected clients per Access-Point? I am using a 5508 WLC.
View 4 Replies
View Related
Jun 16, 2012
Is it possible to limit what users are able to do and view in the webconsole of a WLC 5508 via ACS. I have ACS setup to restrict what commands can be run depending on user on the CLI however when they log into the webconsole they can access everything?
View 2 Replies
View Related
Apr 12, 2013
I am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
View 5 Replies
View Related
Jun 20, 2012
Our ASA is a 5580 version 8.1(2) and is the L2L VPN peer for a handful of remote offices including a L2L VPN with a vendor who will provide a service for these remote offices. I have two questions/issues:We will need to provide this vendor access to the remote office network(s) only on port 9100 (printing to specific printers at these offices). I know there is an issue with L2L VPNs ability to see each other but if there is a global command allowing all to see each other that would be bad as we have others and don’t want all to see each other.The remote offices are using CIDR 172.20.0.0/16 so each one is assigned for example 172.20.3 the next office is 172.20.4 and so on. For the crypto map access list for this vendor can we use 172.20.0.0/16 or do we need to specify each individual network?
View 3 Replies
View Related
Oct 26, 2011
I have cisco3750 (core), 3550,3548, 2960, HP Procurve 2510 series, Extreme e250 series swiches running in my network. Now all are running by default. How can I deploy rstp here? Or which is the best loopdetection protocol is best here ? I have aroung 40 vlans . (not looking for PVST )
View 9 Replies
View Related
Dec 9, 2012
We are doing a study on our public WiFi to identfy client connections based on wireless Vendor. about 40-50% of the clients wireless Vendors are "unknown". Is there a way to update the list of Vendor mac-addresses in WCS?
View 5 Replies
View Related
Apr 2, 2012
I am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
It is a PIX 506e firewall with PIX v6.3.
View 1 Replies
View Related
Feb 3, 2013
We have a 7609 in production network and I am trying to find out the SFP vendor plugged in module WS-X6724-SFP."show inventory raw" gives me the SN but not the vendor name. "show hw-module subslot 1/1" shows The indicated slot/subslot number is empty. Any commands which can show the SFP vendor?
View 1 Replies
View Related
Dec 25, 2012
We have a L2L VPN with a vendor and our outbound traffic (our local network is 192.168.0.0) NATs over one of our public IP addresses x.x.x.164 to their public IP address 128.x.x.x. In the beginning all our traffic was outbound (port 23) to the vendor and now we need to allow inbound from the vendor to specific 192.168 addresses on our network using port 9100. I’m uncertain as to what I should do to allow their inbound traffic to these IP addresses since we are NATing our entire network over one IP address. Note, the .164 public IP is also used to NAT to other vendors we have L2L VPN with. The VPN terminates to our ASA 5580 version 8.2.
View 5 Replies
View Related
Feb 21, 2005
I'm using Cisco ACS 3.3 for RADIUS. How to do I make Vendor-Specific attribute available? (Attribute number 26, format: OctetString) The online help makes reference to it, but does not tell you how to make it available.
View 9 Replies
View Related
Nov 28, 2012
What is the difference between open protocols and vendor specific protocols?
View 1 Replies
View Related
Apr 3, 2013
I tried many different things to get the accurate answer for my issue. I wanted to know, will i face any connectivity or looping issue in the network if i connect Broacade SAN switch on a cisco 6500 switch.Also need to know to maintain a DATA DOMAIN which SAN switch is better? Cisco or other vendor.
View 2 Replies
View Related
May 20, 2013
I have arequirement where in I need to allow only specific vendor made desktops/laptops to be connected to the switch and block the rest. Say I want only the HP made Laptops to be connected on the Network. and block all other vendors. such as dell, ibm etc.
I am having Catalyst 4500 switches in My network. i tried using the mac access list using the permit and deny statement and then mapping the access list to the vlan access map and then filter using the vlan id. But this doesnt work on cat 4500....the same I tested for 2950 switch and it works perfectly. are there any restrictions on 4500 or any extra configuration has to be done.
View 2 Replies
View Related
Sep 26, 2011
I’m trying to configure EAP-Fast following the guide [URL].But when I try to download the certificate, I receive the follow message: “Error installing certificate.”At logs I see:
*TransferTask: Sep 27 14:00:09.479: %UPDATE-3-CERT_INST_FAIL: Failed to install Webauth certificate. rc = 1
*TransferTask: Sep 27 14:00:09.479: %SSHPM-3-KEYED_PEM_DECODE_FAILED: Cannot PEM decode private key
- Remembering I’m doing Device Certificate.
My environment is:
WLC 2106 Windows 2003 with AD and CA When I try to use line commands I can’t too.
View 2 Replies
View Related
Sep 10, 2012
I have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
View 10 Replies
View Related
Feb 10, 2013
when any user logs into LMS #1, GUI says "user not authorized to view devices". All of my users are set to "full permissions" so it seems to be some disconnect here. I'm using ACS for auth, that seems to be working OK. I have a second system LMS#2, setup exactly the same, which works properly, all "full permission" users can access all device menus.
View 1 Replies
View Related
Oct 10, 2012
we have installed a new appliance of LMS 4.2.2 in our VmWare environment. The platform is running licensed to work with 1300 devices. We have approximately 500 devices in DCR, most of them are small switches ranging from Catalyst 2950 to Catalyst 3750, and also a bunch of Nexus 5548 switches.CiscoView is not working for any of them, we get an error message which we cannot interpret. We have updated to the newest possible device packages, but all to no avail.
View 2 Replies
View Related
Nov 21, 2012
We have installed LMS 2.5.We are not able to view TOC(Table of Contents of RME(4.0.3).
View 2 Replies
View Related
Oct 15, 2012
I am trying to access the cisco view but a message appears notifying me to install the devices packages, i have tried to do an online update from the software center, but it did not work.
the devices that i have are, 2960 switches and 6500 switches and 3560 switches.
View 1 Replies
View Related
Aug 7, 2011
best way to monitor delay, latency and jitter between sites connected by VPN? I have CiscoWorks LMS 4.0 but that doesn not seem to be able to do the job (or I just don't know how to to it in LMS) Even a 3rd party application will do. I would prefer not to have to place hardware at each location though.
View 2 Replies
View Related
Oct 13, 2011
I have a cisco 2911 router that is located in my head office LAN and I use this router to connect to my branch networks. I want to configure IP SLA Monitor on this router to track my WAN Links but it does not support the command IP SLA Monitor. My IOS VERSION is c2900-universalk9-mz.SPA.151-2.T1.bin. how I can configure IP SLA on my router.
View 4 Replies
View Related
Dec 7, 2011
We are using LMS 4.0 in my office. We want to monitor our ISP router (cisco 888 or 892), the ISP open some MIB (IfMib and Cisco and these OID :1.3.6.1.2.1.2.2 / 1.3.6.1.2.1.31 / 1.3.6.1.2.1.4).
I use Cacti as LMS for the graph, in cacti I have the graph for the devices, but in LMS in the Topology Services, the router stay in red and in state Unreachable.Do you know what is the mechanism used by LMS to see the state of a device and which MIB or OID do I have to open on the routers?
View 3 Replies
View Related
Jul 1, 2012
my laptop only has hdmi port and my tv only supports s-video and scart connection but i've an old pc that has s-video connection and i was wondering if i can "send the screen" from my laptop to my old pc via lan is there a way of doing that at high fps? remote desktoping works but it's very slow.
View 2 Replies
View Related
Nov 8, 2012
I have a DVR connected to my router.I have viewed the cctv over the net before using this setup, but I think I need a DNS service so that I can use IE to log in remotely? The free one I signed up to before wants money - I only need it for a few days while i am away
View 3 Replies
View Related
Aug 16, 2012
want to view the Log on the Cisco 2821 router for any issue occur.
View 2 Replies
View Related
Feb 20, 2013
view cached CDP neighbor information in LMS 4.2.
In LMS 3.1 it is displayed in the Device Center summary section, but I cant find it in LMS 4.2 Device Center.
View 4 Replies
View Related
Mar 12, 2012
The regular problem with the LMS topology and WAN Links when you see the branches are disconnected from the HQ BUT in my case the branches are already connected via Layer2 links but unfortunately some intermediate layer2 modem/switch exist in some branches which prevent CDP discovery but you will find both HQ and branch router in the same subnet .
View 1 Replies
View Related
Nov 28, 2012
How to get the Detailed Device View in LMS 4.0 ? From what I have been able to find out I should be able to go do Monitor> Fault Settings> Setup> Fault Device Details, select a device, click View and then click the device name link.Unfortunately the device name(s) displayed are not links, just text.
I need to get the the Detailed Device View so that I can block certain interfaces/events from generating alarms, specifically ISDNB channels when voice calls are made.
View 4 Replies
View Related
Apr 23, 2012
I can connect via VPN with the QVPN but once I am connected to my network I cannot view the resources available to me by LAN. I am nowhere near aware as to why.
View 4 Replies
View Related
Oct 23, 2011
I upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies
View Related
Apr 16, 2012
How can view the scheduled archiving job in lms 3.1 ?
View 1 Replies
View Related
