Cisco VPN :: How To Enable Xauth On Pix 506E
Feb 20, 2012
it is possible to enable Xauth on pix. I have read multiple threads about using the following cmds:
username test123password testing privilege 2
aaa-server LOCAL protocol local
crypto map mycrypto client authentication LOCAL
However the f/w wont let me add the crypto map cmd, just comes back with the following:
PIX(config)# c.rypto map mycryptomap client authenication LOCAL
Usage: [ show ] crypto { ca | dynamic-map | ipsec | isakmp | map | sa } ...
show crypto engine [verify]
[ show | clear ] crypto interface [counters]
I also tried the following, but they dont work and I am not sure if they are meant for Xauth since I was under the impression that it had to be enabled globally.
PIX(config)# vpngroup test authentication-server LOCAL
Protocol "local" is not supported for authentication of remote users of a h/w client
PIX(config)# vpngroup test user-authentication
[code]....
View 3 Replies
ADVERTISEMENT
Nov 17, 2008
I have problem auto connect Easy VPN client to Easy VPN server using saved X auth username/password. The ez vpn client is a Cisco 2691 using IOS 12.4.15T7. The config is as follows:
crypto ipsec client ezvpn EZ
connect auto
[code]....
the router keeps prompting me to manually enter username/password. connectivity will work be established after i manually enter the username/password. But this is not what i desired. I need it to connect automatically.
The Ez vpn server is a 7200 running 12.4.22T. Config as follows:
aaa new-model
aaa authentication login USERAUTHEN local
aaa authorization network GROUPAUTHOR local
[code].....
View 7 Replies
View Related
Jul 1, 2006
how to disable XAuth for Remote VPN users on the ASA 5510 running 7.2(1)?
HPMFIRE(config)# tunnel-group vpn3000 general-attributes
HPMFIRE(config-tunnel-general)# authen
HPMFIRE(config-tunnel-general)# authentication-server-group none
ERROR: The authentication-server-group none command has been deprecated.
The isakmp command in the ipsec-attributes should be used instead.
--[code]....
I couldn't find anything under isakmp to disable it.
View 2 Replies
View Related
Mar 4, 2011
How to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies
View Related
Oct 28, 2012
I seem to be having an issue with my PIX configuration. I can ping the VPN client from the the internal network, but can cannot access any resources from the vpn client. [code]
View 4 Replies
View Related
Mar 17, 2013
There is a PIX 506E and ASA5510, with different connection to service provider. Problem is Apple remote users can't access resources protected by the PIX506E. Apple users can access resources protected by ASA5510. Physically the PIX and ASA are in close proximity with no physical connections. Is it possible for Apple users to authenticate with the ASA and the traffic get routed to and get authenticated by the PIX, inorder to access resources?Due to bandwidth restrictions, a DMZ on the ASA will not be created at this time inorder to consolodate firewalls. Currently 2 x T1 is the connection between ASA and ISP; 1 T1 connects PIX to ISP.
View 1 Replies
View Related
Nov 19, 2012
I have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies
View Related
May 4, 2013
So i got a Cisco PIX 506e from a friend and want to set it up for a VPN. Though i cant download the PDM (PIX Device Manager) since i dont have a Contract or something like that. So i cant set it up.
View 1 Replies
View Related
Jul 7, 2011
I have 2 firewalls in my network: ASA 5505 and PIX 506E. Both firewalls's internal network is in the 192.168.0.0/24 subnet but their external addresses are different of course. The inside IP for ASA 5505 is 192.168.0.254/24 whereas the PIX is 192.168.0.1/24. I've successfully configured VPN on the ASA 5505. I'm able to VPN to the ASA and can ping / access hosts that have the 192.168.0.254 as their gateways.However, I'm unable to ping/access hosts behind the PIX. What do I need to do in order to allow access to the network behind the PIX after I VPN to the ASA? Also, I'm unable to ping 192.168.0.254 after I VPN to the ASA.
View 5 Replies
View Related
Apr 29, 2012
I need to replace an ageing PIX 506e with an ASA 5505.The current setup looks like this: The PIX is used for site-to-site VPN connection via the WAN 2 link. The WAN 1 link is used for general Internet connectivity.I don't have access to the Draytek Router as it is supported by a 3rd party, but I believe it uses static routing to direct the relevant traffic to/from the PIX.
When I replace the PIX with the ASA, the inside i/f connection experiences dropouts - but no errors show in the logs.The only significant difference I can see in the config is that the ASA utilises VLans for the inside & outside interface configs - I used the PIX-to-ASA Migration tool to make the initial configuration on the ASA.In tests, if I only connect the inside i/f of the ASA, pings from the LAN are stable. Once I connect the outside i/f, pings timeout approx 80% of the time.
View 2 Replies
View Related
Jan 10, 2011
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
View 4 Replies
View Related
Mar 5, 2011
I am trying to add a username to the local database for remote VPN connection but always i get this error when I add,Encrypted password is of incorrect lengthUsername addition failed.
View 1 Replies
View Related
Apr 2, 2012
I am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
It is a PIX 506e firewall with PIX v6.3.
View 1 Replies
View Related
Mar 11, 2013
I just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
View 4 Replies
View Related
Mar 22, 2011
What is the easiest way to restore my config? I backed it up yesterday with my tftp server. Today I made some changes and messed some things up and need to restore the config from yesterday.
View 1 Replies
View Related
Feb 26, 2013
I'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
View 3 Replies
View Related
Apr 7, 2010
I trying to do password reset on a 506e that I got with the current password unknown. I've gone to the Cisco URL for the reset: [code]
I am using the correct bin file as I checked with my pix version. Also I CANNOT ping the firewall from a PCor system on the network, but CAN ping everthing from the PIX.I've tried using interface 1 but no go. Also I've checked the TFTP software (Solarwinds) is running fine and I've unblocked it in XP's firewall.
View 2 Replies
View Related
Feb 5, 2011
So I have a Cisco PIX 506e that I've modified a bit, but am quite happy w/ when it comes to performance and configuration (I can actually set up the VPN server w/o too much thought.) I also have a Mikrotik Routerboard 750, I'm no longer using it as my router due to a few config issues I had plus the fact I had to hard code my internet gateway's arp address into the device due to some issues.
What I am wanting to do, which I'm sure is possible and easily accomplished (I just don't have the time right now to try it) is set the routerboard up behind my pix and have it function as an ipv6 router, while the pix handles my ipv4 duties. I've already set up the routerboard w/ an ipv6 tunnel broker when I had it running as my router, I am just curious if it will work in a similar fashion when configured behind an ipv4 device.
View 2 Replies
View Related
Feb 27, 2012
I have a problem with PIX 506E that meets the version 6.1, and in an simple computer network equipment seems to behave in strange ways because some web sites do not open or very open slow thereby its operation impracticable. On the other hand other web sites open normally.
Querying the web site of the Cisco, I found several documents discussing the same problem but in a later version ( 7.0 ), not in this version 6.1.
I've tried removing the pix from the network , not the error occurred, again insert pix however tested only with a machine, without the rest of the network and the problem persists
View 13 Replies
View Related
Sep 20, 2012
I like to set up a pix and router for this network for a small buss, but I need to know what type of cable do I need to set this connection to work straight through or a cross over cable? also I need a subgestion if a nat would work better on the pix or leave it on the router?
View 4 Replies
View Related
Dec 14, 2011
i'm looking to change my pix 506e for an rv042,is it a bad move or a good move ? is the rv042 much better than the 506e? i want to change to an rv042 because it's easier to manage! 506e is currently doing this :
-firewall for a web hosting company (7 servers)
-2 vpn tunnel
-one-to-one nat.
performance side : is the rv042 much better than the 506e? should i pick up an rv082 or an rv016 ? are they much better than the rv042 ?
View 2 Replies
View Related
Sep 20, 2012
So I was doing some testing with my BB Playbook where I wanted to see what outside connections it tried to make during startup and whatnot. I have a pix 506e running 6.3(5). I created an simple 'deny ip any any' access list on the inside interface so that the Playbook doesn't actually make any connections, but I set up a 'capture' on the inside interface accepting 'ip any any' to see what kind of traffic I could see heading outbound from the Playbook. Well, it started off showing attempts to query DNS (and failed, naturally), but then after a couple of minutes, it tried to connect to a couple of IPs over port 443 and actually got a response!!! For the life of me, I can't figure out how this can happen. NO traffic should be allowed outbound due to my explicit 'deny' rule, but for some reason some traffic on port 443 made it past the firewall and got a response back. There are no other rules in the access list except the 'deny' rule. My PIX configuration is quite simple and I cannot see anything that would allow the Playbook traffic to circumvent the access list.
I've come to think that either RIM has found away around Cisco access-lists, or there is a bug in the Pix OS. I know it's an old appliance/OS, but still. I wouldn't think it could be THAT easy to bypass the firewall.
View 4 Replies
View Related
Nov 23, 2011
How to enable GUI for a Cisco 1841?
View 4 Replies
View Related
Nov 23, 2011
How to enable GUI for a Cisco 1841?
View 1 Replies
View Related
Sep 12, 2011
configuring AAA on 1841 router, initially it authenticates me well using my TACAS+ login. but though i have configured enable password in router, router directly puts me in privilage mod without asking enable password .
my configs for AAA as below
aaa authentication login ACS group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization exec ACS group tacacs+ local
aaa authorization commands 0 ACS group tacacs+ local
aaa authorization commands 15 ACS group tacacs+ local
aaa accounting commands 1 ACS start-stop group tacacs+
aaa accounting commands 15 ACS start-stop group tacacs+
View 8 Replies
View Related
Apr 16, 2011
Im using WCS v7.0, I want wcs to send me an email when an AP goes down. Is it possible to do it on wcs? If so, how?
View 1 Replies
View Related
Sep 25, 2012
I have a Cisco 5508 controller and am considering using LAG. Can I enable LAG but only use 2-4 of the 8 available ports on the 5508? I am asking because currently I don't have enough ports on my 3750G switch to accomidate all 8 ports on the 5508.
View 2 Replies
View Related
Mar 31, 2013
I was trying to upgrade IOS on my 3500XL series switch (24 port) Before doing this I connected my switch and deleted all the configs and flash. When I reconnect my switch this is the error message I am getting.
View 7 Replies
View Related
Feb 18, 2012
i wanna ask a question regarding automatic startup on lms 4.1, i have installed my LMS 4.1 on esxi 4.x . but recently my server sometimes down because the electricity problem. and when my friend push the power button to start the server, the LMS is not automatically active. is it possible to make it automatically active soon after my server power up ?
View 3 Replies
View Related
Nov 17, 2012
I have several PIX 501's and one of them is extremely slow accessing network resources and does not have Internet access. I would like to use split tunnel and have them access the Internet throught their DSL connection and any traffic for network resources sent over the VPN. How can I improve the speed and set up split tunnel via the command line? I dont have the PDM software so I guess I will need to do all the configuration via the command line. Below is the configuration:
PIX Version 6.3(1)interface ethernet0 autointerface ethernet1 100fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password k4HlcGX2lC1ypFOm encryptedpasswd y5Nu/Nt1/5dK8Iuf encryptedhostname
[Code].....
View 1 Replies
View Related
Jan 3, 2012
I just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies
View Related
Mar 23, 2011
How to enable the VPN-3DES-AES and another ASA Box.Mate's license (VPN-3DES-AES Enabled) is not compatible with my license (VPN-3DES-AES Disabled). Failover will be disabled.The license on secondary is not compatible for secondary ASA for the failover. [code]
View 2 Replies
View Related
May 20, 2009
I am trying to enable IP SLA on a Cisco 4948 switch (running 'cat4500-ipbasek9-mz.122-46.SG.bin') to test CiscoWorks IPM using this swtich as a source device. But I can't run the command "ip sla monitor" on this switch. It just has "ip sla responder". Is it possible to configura IP SLA on this source switch? Or can I do it only on routers?
View 6 Replies
View Related
