How to enable the VPN-3DES-AES and another ASA Box.Mate's license (VPN-3DES-AES Enabled) is not compatible with my license (VPN-3DES-AES Disabled). Failover will be disabled.The license on secondary is not compatible for secondary ASA for the failover. [code]
View 2 Replies
I need to enable VPN-3DES-AES on an ASA5540. Show version provided this info below.
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 200
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Disabled
[Code]....
This platform has an ASA 5540 VPN Premium license.After doing some poking around I came across a link to request a free license but when the email came it warned that the requested license was lower than one currently assigned to the serial number provided. I do not have any of the old license information since this was set up years ago and was way before my time with the company. How to enable the feature as well as maintaining my vpn premium license features.
I have a PIX 515E UR which I would like to activate the VPN-3DES-AES license. I did find a link to register the license, but after following the link and logging into my old CCO account i found that as I didn't have access to anything, so couldn't complete the procedure.Is there any way that I can get the license activated? I bought the unit from a Cisco partner quite some time ago, but never needed the 3DES license. Now I do.
View 3 Replies View RelatedI have Asa 5510 with base license and no 3des free license installed on to it.Will it be required for both the licenses to be installed on it for site to site tunnels to establish.This firewall is not taking the below commands to give and the tunnel is not getting through.tunnel-group x.x.x.x type ipsec-l2ltunnel-group x.x.x.x ipsec-attributes.
View 3 Replies View RelatedIs it required for the 3des license upgrade for the asa5510 to reboot for the further configuration of site2site tunnels.
View 1 Replies View Relatedhow can i disable the 3des encrption feature in ASA5505?
View 1 Replies View RelatedI recently applied a new activation key to an ASA5512 to add the 250 anyconnect essentials user. However, after reboot, I lost the 3DES/AES license which now reads disabled.
how to re-install the 3DES key?
I cannot find the old "Get a FREE 3DES" activation link - it says http:403 error.
I have a simple setup where I have a 2911 router with three interfaces, Inside, Outside and a second "Inside" interface which is labelled as a DMZ. The Zone Firewall applied to the "DMZ" is actually Inside (until I can work through problems). I need to be able to access a device on the DMZ via its external IP so I have designed NAT to use IP Nat Enable commands. This is now working for me fine. However, since utilising IP Nat Enable, my zone firewall now denies return TCP / UDP traffic and consequently I no longer have any internet access. Looking at the syslog messages, the reason for this is that the router is denying these return flows not because they are matching the outside-to-inside policy, but rather they are matching the outside-to-SELF policy. The router seems the detect that the internet traffic is being returned to SELF, when in reality the NAT rule should pick this up and forward it to inside. I can understand why this is happening, because I am NATting all private / inside traffic behind the external IP of the router, which is assigned to the Gi0/0 interface. [code]
View 1 Replies View Relatedif y need to enable VPN IPSec through the firewall. y just need to need to allow the port 4500?
View 2 Replies View RelatedMay I know how to configure for remote accessing ASA 5525 via ssh?I have issued the following commands
ssh 10.60.0.0 255.255.0.0 outside
ssh 10.60.0.0 255.255.0.0 dmz
ssh 10.60.0.0 255.255.0.0 inside
ssh timeout 5
but I am not able to access ASA via ssh. Do I need to add any other command
my windows is no longer connecting to the internet.i I ran a diagnostic and it said to check firewall settings for the http port(80), https prt(443) and the ftp port(21). I haven't change anything in my settings and dont know why all of sudden i hvae to check firewall settings.
View 1 Replies View RelatedI am trying to enable Ftp traffic through our firewall at work. We have a Cisco 5505 ASA and we cannot access any Ftp servers outside our network. We are running 8.3(2). Any have commands I can run to allow us to connect to ftp sites?
View 6 Replies View RelatedI have a pair of brand new 5520s I am in the middle of commission. After carving out all the DMZs etc I needed I realized that I really neede another physical NIC, not just another VLAN off a configured nic. [code]I am running 8.3(2). How can I turn these "Not used" interfaces into useable ones?
View 2 Replies View RelatedI'm replacing a new ASA 5505 due to a corrupted flash. On the original unit, I had the ability to SSH into the device using TeraTerm with no problems. While configuring the new device, I entered commands to enable SSH into the unit.
View 5 Replies View RelatedWe would like to enable our HelpDesk and Network team the ability to connect to Laptops using our ASA 5510 VPN device using Secure VNC application. Not sure if this is possible or how to enable this option.
View 5 Replies View RelatedWe recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)
[Code].....
I have just erased an ASA and upgraded the firmware and then added an IP. How can I enable the ASDM as I can't get on it, here is the config:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
dns-guard
[code]....
how do i enable port forwarding on the CLI for ASA 5510. outside subnet is 192.168.1.0/27. when i try to ping another IP with that range i can't access.
View 37 Replies View RelatedI am trying to enable access to use RealVNC on our Cisco ASA 5505 without using VPN. RealVNC uses port 5900. Users should be able to vnc to 99.23.119.78 and reach our internal server 192.168.1.4. So far they are receiving connection refused.
View 5 Replies View RelatedI've done this in the past for specific host entries with no problem, but I can't figure out how to do this for an entire subnet. I need something along the lines of the following:
access-list OKC2DAL extended permit ip 192.168.1.0 255.255.255.0 192.168.107.0 255.255.255.0
static (inside,outside) 192.168.99.0 access-list OKC2DAL netmask 255.255.255.0
I see netmask as an option, but the ASA states "invalid option netmask." The ASA is running 8.2(2). OKC-PIX(config)# static (inside,outside) 192.168.99.0 access-l OKC2DAL ?
configure mode commands/options:
<0-65535> The maximum number of simultaneous tcp connections the local IP
hosts are to allow, default is 0 which means unlimited
connections. Idle connections are closed after the time
specified by the timeout conn command
[code].....
I have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies View RelatedI have configured dhcpd in an ASA 5505 and every thing is working. I am testing it to give me a warning when the address pool is about to be finished or it is empty. But don't konw how to do it. if I run the "debug dhcpd packet", i get that the address pool is empty.
View 3 Replies View RelatedWhat is Anti Spoofing in ASA 5505. Can I enable it on ASA 5505. If yes , port will be inside or Outside. ? or both ?
View 1 Replies View RelatedI get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
how to enable inspect http on ASA 5510, so that URL information populate in the syslogs?
View 2 Replies View RelatedWe are runing PIX 535 with software version 8.02. In ASDM, I see anti-spoofing is diable in all interfaces. If I enable it, is there any negative effect? Can I enable it in DMZ, inside, and outside interfaces?
View 2 Replies View RelatedI am currently troubleshooting a firewall policy on a ASA 5505. What command can enter in the CLI to enable live view of traffic been block and which traffic is been allow?In my experiences with other firewall vendors, other firewalls allow me to narrow down the source and destination, too. is there such thing on the ASA 5505?
View 6 Replies View Relatedmy 1841 router can't resolve dns after enable ios firewall, I try to ping google.com from router's console fail, but dns resolution is fine from lan side.
my partial config---------------------------------
!
ip name-server 8.8.8.8
[Code].....
Where on my router interface I could go to enable both the SPI Firewall, and the Wireless MAC Filtering? I have the D-link DIR-815.
View 1 Replies View RelatedI have ASA5505 as my main router (192.168.15.1) and it currently it also serves as DHCP server. I have a WNDR3700 (192.168.15.2) which work as an access point and it provide wireless access for wireless devices. I have few dhcp clients where i can't setup static IP, and i want to restrict them to use static IP through MAC reservation.
1. Make ASA5505 to do the MAC reservation f, which will be easy setup for me. But as per my search its not possible.
2. Disable dhcp on ASA and enable dhcp on my WNDR3700. i tired this and dhcp clients are getting IP from wndr3700, but the problem is dhcp clients gateway defaults to 192.168.15.2 (as well as dns) and therefore no internet connection.
How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
Today I upgraded my Cisco ASA 5505 ASDM from version 6.34 to 6.41 cause of some problems on old version with NetFlow. But now when I switch to dashboard i can not see "Top Usage" tab. That was quite usefull for me. It simply disappeared.
Can i somehow configure which tabs are displayed on dashboard ? I really need that one and I do not want to downgrade :/
I try to change password on the ASA 5520 device and its not getting changed.
FW(config)# enable password cisco1234(config)# end
After that I perform a write memory.
But somehow I relogin again the enable password still remain as the old enable password
version : 7.2(5)2.
