Cisco Firewall :: Enable Netflow On ASA 5505 For Vlan And Interfaces
May 17, 2013
How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
View 9 Replies
ADVERTISEMENT
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
View Related
May 12, 2011
I have a pair of brand new 5520s I am in the middle of commission. After carving out all the DMZs etc I needed I realized that I really neede another physical NIC, not just another VLAN off a configured nic. [code]I am running 8.3(2). How can I turn these "Not used" interfaces into useable ones?
View 2 Replies
View Related
Feb 20, 2013
Today I run into a problem with enabling ICMP traffice between two inside interfaces on ASA5510 (version 8.2). I tried to ping from 192.168.1.2 to 192.168.2.2 Failed. But I can visit outside websites or ping from any of the two addresses above to 8.8.8.8 So I checked the configuration shown as follow
<omitted>
interface ethernet0/1
nameif inside
[Code]....
View 3 Replies
View Related
Aug 22, 2011
5505 ASA, 8.2(1) ,We can not get it to report Netflow to the collection agent at 192.168.1.34. Here is the commands I've entered:
asa# show run | i flow
access-list netflow-export extended permit ip any any
flow-export destination inside 192.168.1.34 2055
flow-export template timeout-rate 1
flow-export delay flow-create 60
class-map netflow-export-class
match access-list netflow-export
flow-export event-type all destination 192.168.1.34
policy-map netflow-export-policy
class netflow-export-class
flow-export event-type all destination 192.168.1.34
View 6 Replies
View Related
Jul 14, 2012
I have ASA 5585 with SSP20. I want to enable same security level subinterfaces (routed mode) to communicate with each other.
I have put below command at global level but somehow it is not happening.
hostname(config)# same-security-traffic permit inter-interface
Do I also need to check for NATing or some other things apart from above command?
View 2 Replies
View Related
Nov 13, 2011
Unable to create VLAN interfaces in ASA 5510
View 1 Replies
View Related
Mar 20, 2012
Got new ASA5550, code 8.2.2 in flash, can't configure "nameif" or "ip address" on the interfaces: [code] These are all the options that I get! Another weird thing I noticed is "<system>" string in "show ver" top line: [code]
View 2 Replies
View Related
Mar 18, 2012
I would like to run some NetFlow monitoring on a few sub interfaces on a router. This is a 7301, with an NPE-G1.What I want to know is, does Cisco have a page anywhere (because I can't find one) that lists typical additional CPU and memory loads one can expect when enabling NetFlow on an (sub)-interface; perhaps for a given speed (Mbps) and/or number of flows?I don't want to enable NetFlow and then bring the device to a grinding halt, how can I know what sort of overhead to expect?
View 2 Replies
View Related
Jun 13, 2012
I am fairly new to configuring ASA's. I have an ASA 5505 with one outside interface and three inside interfaces (inside1, inside2, and management). I need inside1 and inside2 to be able to talk to eachother but cannot work out how to make this happen. They are both configured to the same security level and the 'Enable traffic between interfaces with same security level' box is ticked. I have also tried adding appropriate NAT and Access rules. The packet tracer suggests the rules are correct for allowing traffic flow between interfaces but obviosly this may not be the case.
View 14 Replies
View Related
Aug 18, 2011
It is my understanding that ACLs can only be bound to logical interfaces using the access-group command. However, is it possible to somehow apply ACLs simply based on the ASA's local Ethernet interface? For instance, consider the following:
Device A with IP 192.168.1.1/24 is connected to Ethernet0/0 on the ASA. Device B with IP 192.168.1.2/24 is connected to Ethernet0/1 on the ASA.
Since both devices are in the same subnet and presumably the same VLAN, is it possible to manipulate the traffic to and from physical Ethernet interfaces using ACLs in this manner?
My predicament is fairly simple:
Internet --- ASA --- ROUTER
|
DMZ
In addition to NAT, VPN, and various other tricks, my ASA is also routing traffic from my internal LAN and the Internet to servers in the DMZ configured on the ASA. Due to a combination of Internet and DMZ traffic, my relatively slow ASA is struggling to route and thus becoming a bottleneck. My router is comparatively modest in terms of functionality when compared to the ASA but it is fast. My ideal solution would be to somehow harness the ASA's filtering capabilities for my DMZ but use the router to get traffic to and from my internal LAN into the DMZ without using the ASA to route it.
Additionally, it is worth noting that my DMZ is fairly restrictive so using protected or isolated ports would not quite work for me.
View 1 Replies
View Related
Nov 9, 2011
I trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
View 1 Replies
View Related
Sep 23, 2011
I have an ASA 5505 running 8.2(1), that is configured with three interfaces as follows:
Inside (security 100) 10.0.0.0 /24
Inside 2 (security 100) 192.168.0.0 /24
Outside (security 0) internet
Inside is connected to my internal network, inside 2 is connected to the network of a sister organization, outside is outside.
I'd like to be able to route between from inside to inside 2, and have NAT translate me to inside2's address.
I have inter-interface traffic configured, and when I use a NAT exemption, I can route fine. But the resources on network 2 must see my request as coming from the inside2 interface IP.
View 2 Replies
View Related
Mar 6, 2011
My customer is running an ASA5505 with 8.3 code.
The have a somewhat flaky proxy between their inside LAN and the firewall. I'd like to have a configuration as follows:
LAN > Proxy > VLAN 1 (eth0/2) on ASA
and
LAN > VLAN 1 (eth0/3) on ASA
So that in the event of Proxy failure (let's just say it loses power) the eth0/3 interface will kick in.
This appears to be easily configured according to the documentation:
"The following example creates two redundant interfaces:
hostname(config)# interface redundant 1
hostname(config-if)# member-interface gigabitethernet 0/0
hostname(config-if)# member-interface gigabitethernet 0/1
hostname(config-if)# interface redundant 2
hostname(config-if)# member-interface gigabitethernet 0/2
hostname(config-if)# member-interface gigabitethernet 0/3"
But these commands don't seem to be available on a 5505.
View 7 Replies
View Related
Aug 2, 2011
I'm replacing a new ASA 5505 due to a corrupted flash. On the original unit, I had the ability to SSH into the device using TeraTerm with no problems. While configuring the new device, I entered commands to enable SSH into the unit.
View 5 Replies
View Related
May 14, 2012
We recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)
[Code].....
View 2 Replies
View Related
Jan 21, 2013
Below is the show ver of 6509 switch , how to enable netflow
sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI7, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 18-Jul-11 05:50 by prod_rel_team
[code]....
View 2 Replies
View Related
Sep 3, 2008
How to enable Netflow on the ASA5540
View 10 Replies
View Related
Aug 17, 2011
Cisco 2951 w/ HWIC-4ESW
IOS 15.0(1)M5
#sh ip flow int
Vlan533
ip flow ingress
ip flow egress
#
The SVI sends the flow data just fine, however I also continue to receive flow data from most other interfaces.
I have attached a screenshot of one of our netflow collectors indicating that many of the interfaces are sending flow data even though not configured to do so. We have two different netflow collectors, from different vendors and both confirm the same interfaces sending flow data.
Normally I wouldn't care and ignore it, however one of them uses a license limit by interface and is a bit problematic.
View 2 Replies
View Related
Nov 29, 2012
I've got an issue with SNMP and netflow tools. They are displaying different data for the same (sub)interfaces.I've got metroethernet link which connects root A (Cisco 7606, 12.2(18)SXF8) and root B (Cisco 2811, 12.3(11)TS). MPLS is configured on the link (behind root B there is no more MPLS). I'm attaching root configurations (I've ommited parts of config).Interfaces are:
Root A - gi2/6.2144
Root B - fa0/1
I've configured SNMP and netflow on both devices. I'm using two SNMP tools (CA Spectrum and eHealth) and two netflow tools (CA NetQoS Reporter Analyzer and Fluke Networks NetFlow Tracker) to collect the data. SNMP tools show the same info for defined (sub)interface.Netflow tools also show the same info for defined (sub)interface. I'm attaching reports from one SNMP tool and one netflow tool for the same time period.
1. Looking at SNMP tool, it can be seen quite amount of that data in both in and out direction.
2. Looking at netflow tool, it can be seen quite amount of that data in out direction, while in direction shows small amount of data.
I'm aware that Cisco has difficulties with SNMP counters on subinterfaces. I'm also aware that MPLS netflow has its own difficulties.Root B netflow configuration is quite simple as it has just 2 interfaces to configure netflow on (Fa0/0 and Fa0/1). So I would guess SNMP and netflow data should match, but they don't. When you look at SNMP tool reports for roots A and B, it can be seen that traffic volume is practically mirrored.
View 3 Replies
View Related
Feb 27, 2011
I am trying to enable access to use RealVNC on our Cisco ASA 5505 without using VPN. RealVNC uses port 5900. Users should be able to vnc to 99.23.119.78 and reach our internal server 192.168.1.4. So far they are receiving connection refused.
View 5 Replies
View Related
Aug 11, 2011
I have configured dhcpd in an ASA 5505 and every thing is working. I am testing it to give me a warning when the address pool is about to be finished or it is empty. But don't konw how to do it. if I run the "debug dhcpd packet", i get that the address pool is empty.
View 3 Replies
View Related
Apr 24, 2011
What is Anti Spoofing in ASA 5505. Can I enable it on ASA 5505. If yes , port will be inside or Outside. ? or both ?
View 1 Replies
View Related
Nov 1, 2012
I get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
View 14 Replies
View Related
Mar 14, 2012
I am currently troubleshooting a firewall policy on a ASA 5505. What command can enter in the CLI to enable live view of traffic been block and which traffic is been allow?In my experiences with other firewall vendors, other firewalls allow me to narrow down the source and destination, too. is there such thing on the ASA 5505?
View 6 Replies
View Related
Mar 17, 2013
I have a 370 with C3KX-NM-10G module & i want to enable NetFlow on it did the specified configs
Step 1 Flexible NetFlow Flow Recordsflow record miketestmatch datalink source-vlan-idmatch datalink dot1q prioritymatch datalink mac source-addressmatch datalink mac destination-addressmatch ipv4 versionmatch ipv4 tosmatch ipv4 ttlmatch ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch transport source-portmatch transport destination-portmatch interface input physical snmpcollect interface output snmpcollect counter flowscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime last flow record miketestegressmatch datalink destination-vlan-id match datalink dot1q priority match datalink mac source-address match datalink mac destination-address match ipv4 version match ipv4 tos match ipv4 ttl match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port match interface output physical snmp collect interface input snmp collect counter flows collect counter bytes collect counter packets collect timestamp sys-uptime first collect timestamp sys-uptime last Step 2 Flexible NetFlow Flow ExporterFlow exporter export-to-samplicatorDestination 10.1.1.8source Vlan1Transport udp 2055option interface-table timeout 60 Step 3 Flexible NetFlow Flow Monitors# Tie the Flow Monitor to the Flow Recordflow monitor mikektestrecord miketestexporter export-to-samplicatorcache timeout active 60flow monitor mikektestegressrecord miketestegressexporter export-to-samplicatorcache timeout active 60
& Applied it to g1/1/1 but without any luck , if netflow works on the
TenGigabitEthernet1/1/1 &
TenGigabitEthernet1/1/2
Only i have four switches stacked and nothing plugged to the
C3KX-NM-10G module
View 1 Replies
View Related
May 8, 2013
I have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
View 4 Replies
View Related
Feb 3, 2011
Today I upgraded my Cisco ASA 5505 ASDM from version 6.34 to 6.41 cause of some problems on old version with NetFlow. But now when I switch to dashboard i can not see "Top Usage" tab. That was quite usefull for me. It simply disappeared.
Can i somehow configure which tabs are displayed on dashboard ? I really need that one and I do not want to downgrade :/
View 7 Replies
View Related
Nov 3, 2011
To enable netflow export on ASR1001, do i need the firewall feaure license or not ?Docs are not really clear, NBAR requires FW license, but i am unsure about Netflow?
View 1 Replies
View Related
Jul 13, 2011
Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies
View Related
Dec 17, 2011
I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....
View 2 Replies
View Related
May 3, 2011
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies
View Related
Nov 22, 2012
I have a machine with two ethernet cards and internet connection, on which Ubuntu 12.04 is installed.Both ethernet cards can take ip adress automatically say,
eth0:47.168.137.14 and eth1:47.168.137.15
I can ping eth0 but can not ping eth1.
Is there a special setting for gettting both ethernet interface active and reachable at the same time.
View 1 Replies
View Related
