I am currently troubleshooting a firewall policy on a ASA 5505. What command can enter in the CLI to enable live view of traffic been block and which traffic is been allow?In my experiences with other firewall vendors, other firewalls allow me to narrow down the source and destination, too. is there such thing on the ASA 5505?
View 6 RepliesI am trying to enable Ftp traffic through our firewall at work. We have a Cisco 5505 ASA and we cannot access any Ftp servers outside our network. We are running 8.3(2). Any have commands I can run to allow us to connect to ftp sites?
View 6 Replies View RelatedI'm replacing a new ASA 5505 due to a corrupted flash. On the original unit, I had the ability to SSH into the device using TeraTerm with no problems. While configuring the new device, I entered commands to enable SSH into the unit.
View 5 Replies View RelatedWe recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)
[Code].....
I am trying to enable access to use RealVNC on our Cisco ASA 5505 without using VPN. RealVNC uses port 5900. Users should be able to vnc to 99.23.119.78 and reach our internal server 192.168.1.4. So far they are receiving connection refused.
View 5 Replies View RelatedI have configured dhcpd in an ASA 5505 and every thing is working. I am testing it to give me a warning when the address pool is about to be finished or it is empty. But don't konw how to do it. if I run the "debug dhcpd packet", i get that the address pool is empty.
View 3 Replies View RelatedWhat is Anti Spoofing in ASA 5505. Can I enable it on ASA 5505. If yes , port will be inside or Outside. ? or both ?
View 1 Replies View RelatedI get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
Today I upgraded my Cisco ASA 5505 ASDM from version 6.34 to 6.41 cause of some problems on old version with NetFlow. But now when I switch to dashboard i can not see "Top Usage" tab. That was quite usefull for me. It simply disappeared.
Can i somehow configure which tabs are displayed on dashboard ? I really need that one and I do not want to downgrade :/
Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies View RelatedI am able to ftp from my Head Office to my test machine at the remote location but I can't get the other way around to work. Error message from the Syslog deny tcp src 192.168.50.5/1825 dst 208.124.202.44/21 by access-group "dmz_access_in".I try a couple of ways to fix it but no luck.A partial config of my ASA 5505. [code]
View 4 Replies View RelatedWe have a BT Infinity broadband circuit which terminates at a vdsl modem, I've plugged an ASA 5505 into the back of this modem and gone through the ADSM quick setup wizard (yes I'm that much of a beginner!) The config that's been generated is pasted below, the symptomns I'm seeing are;
The ASA is setup with PPPOE on the internet connection, I assume this is correct as if I do a show IP on the ASA I'm getting an IP address that has been assigned, if I change the password to the wrong one then I get no IP (as expected).
If I ping from the ASA to an internet connection I'm getting "no route" error messages, if I try a "ping outside x.x.x.x" then I get no repsonses.
The ASA can ping it's external IP, the client machines can ping it's internal, however nothing appears to be able to get out.
ASA Version 8.4(1)
!
hostname xxxxxx
enable password xxxxxx encrypted
[Code].....
We have 110mbps internet service. When we have the 5505 behind the cable modem, our speed drops to 55mbps or so. If we remove the 5505, we see the full 100mbps. I assume the 5505 can handle the speed; if so, what other things should I be looking at?As an aside, we used to have 50mbps wich worked fine, then the ISP upgraded to 60mbps and the through put dropped to 30mbps (It always seems to be half)
View 2 Replies View RelatedMy understanding is for insight to outside we need global and NAT, and for outside to inside we need static and ACL? Traffic goes to high to low, I'm just start working with 5505 recently.
View 2 Replies View RelatedI have VPN up and running between two sites. Both sites have Cisco ASA 5505. I can ping across the devices from both networks. But I cannot remote into the servers on the other network.
View 8 Replies View RelatedI have a Cisco ASA 5505 that I have configured. The outside interface is vlan 2 and the inside interface is vlan 1. Port 0 of the ASA is configured to be in vlan 2 and is connected to the ISP provided subnet. Port 1 is connected to my private LAN subnet. I have an additional router connected to Port 2 for guest connectivity. Port 2 is configured to be a member of VLAN 2 so that it can access the ISP provided subnet. From the device connected to port 2 I can ping the vlan 2 interface address of the ASA and from the ASA I can ping the Default gateway of the ISP provided subnet. For some reason the router on port 2 cannot ping the default gateway of the ISP provided subnet. If the vlan were working the same as a vlan in a switch, I would expect to be able to do this. why it is not working or what I can do to get it working?
View 4 Replies View RelatedI'm trying to allow SSH traffic from the Internet to my DMZ. I gave my remote guy my ip and he can see the ASA 5505 but not get into the DMZ. The outside is 70.165.19.137. The DMZ server is 192.168.60.2. I have the inside talking to the DMZ fine. [code]
View 9 Replies View RelatedI am fairly new to configuring ASA's. I have an ASA 5505 with one outside interface and three inside interfaces (inside1, inside2, and management). I need inside1 and inside2 to be able to talk to eachother but cannot work out how to make this happen. They are both configured to the same security level and the 'Enable traffic between interfaces with same security level' box is ticked. I have also tried adding appropriate NAT and Access rules. The packet tracer suggests the rules are correct for allowing traffic flow between interfaces but obviosly this may not be the case.
View 14 Replies View RelatedWe have 10MB dedicated Internet BW and want to run VC device and due to heavy traffic and BW high utilization at peak hours, VC performance is not sufficient. We would like to reserve 2MB for VC device. How much possible to fix up this configuration in ASA5505 version disk0:/asa724-k8.bin [URL]
View 5 Replies View RelatedI have a Cisco 5505 with a 12Mbps feed. I want to reserve 2Mbps for RTP traffic. I followed the QoS guide here: url... The goal would be that any traffic destined for port 5000 through 5100 UDP or TCP from any IP to any IP on any interface.should always have 2Mbps available to it.
View 5 Replies View RelatedIs there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?
View 4 Replies View RelatedI am trying to switch out a cisco pix 501 firewall with a cisco ASA 5505 firewall. I am not very familiar with all of the commands for the firewalls and have always relied on a standard command line script that I use when building a new one. Unfortunately, my script is not working with the 5505. What I am doing wrong with the following script? I've masked public IP info with xxx.xxx.xxx and I run it right after restoring the firewall to the factory defaults. I am able to get out to the internet if I browse directly from one of the servers, but cannot access a web page when trying to browse to it from an outside network. [code]
View 7 Replies View RelatedI've setup my Cisco ASA 5505 in transparent mode. I have a Cisco 1841 connecting to the ISP (DHCP client) and F0/0 for inside. The 1841 is the DHCP server. I have my ASA 5505 behind the 1841 in transparent mode (Vlan 1 for Outside and Vlan 1 for inside). The router config is good as when you connect a computer straight to the inside interface I get DHCP and can go to internet, no problems what so ever. But When you're trying to go through ASA isn't not working. if I add a ip any any statement to the access list it will work but having an "ip any any" in a access list is like having no firewall at all.
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(4)
!
firewall transparent
hostname ciscoasa
enable password zmQ6OnxvsOOEDNAy encrypted
[code]....
I've got an ASA 5505 with the Security Plus license that I'm trying to configure.
So far I have setup NATing on two VLANs, one called 16jda (VLAN 16 - 10.16.2.0/24) and one called 16jdc (VLAN 11 - 10.105.11.0/24).
From each subnet I am able to connect to the internet, but I need these subnets to also be able to talk to each other.
I have each VLAN interface at security level 100 and enabled "same-security-traffic permit inter-interface", and I have setup static NAT mappings between the two subnets, but they still can't communicate.
When I try to ping there is no reply and the only log message is: 6 Aug 21 2012 09:00:54 302020 10.16.2.10 23336 10.105.11.6 0 Built inbound ICMP connection for faddr 10.16.2.10/23336 gaddr 10.105.11.6/0 laddr 10.105.11.6/0
I trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
I have ASA 5505 with base license. I like to install proxy server in my network.I configured below commands to forward my traffic to proxy server from my ASA.
If there is any configuration that i need to configure.And if possible send me the configuration guide to setup SQUID server. ( Actually it was set up by the 3rd party vendor)
I have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
I need to prioritize voice traffic through the ASA
priority-queue outside
tx-ring-limit 200
queue-limit 2000
Do the above values look correct? and why is the priority queue applied to the outside interface and not the inside? (or both). Also is this the part that ensures that the regular traffic does not choke the voice traffic?
class-map voip-class
match dscp ef
policy-map outsidemap
class voip-class
priority
service-policy outsidemap interface outside
Will the global policy remain which this interface policy taking priority?
I am in search of a new routers. I don't have any special task to do. Just the flow of maximum 2mb/sec data and some times video conference. However I need the Voip solution as well. I just got excited on the cisco ASA 5505 product. Can this fulfill my requirements. Can this work as the router 1841. Does this support DMVPN, SSL VPN and dynamic routing. Can I upgrade the IOS for dynamic routing purpose. Do you recommend to purchase this produe act or not instead of router ? What are the limitations of this product. If I purchase this I can use this as an router as well as strong security solution. How many ports are available for traffic flow in ASA 5505. Are all routed mode or some of them switch port.
View 1 Replies View RelatedWe have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....
I have an ASA 5505 and I setup a port with a PC connected to monitor the LAN interface. I see all the traffic from the LAN going out and traffic coming back in no problem. What I do not see the the AOL Instant Messenger traffic at all. I have WireShark on the PC and I filter for AIM traffic and I see nothing.
View 5 Replies View RelatedI have an ASA 5505 current f/w & the security plus license (to get the 3 nameif interfaces). Can I split traffic between two ISPs, (VPN traffic to one destination on a T-1 on one VLAN, and all other traffic using DSL to another VLAN) and using a different nat policy on both? I know load balacing isn't supported, only failover. I was just wondering if there was a way to make this work.
View 3 Replies View Related