Cisco Firewall :: ASA 5505 Not Allowing Incoming Traffic
Mar 15, 2012
I am trying to switch out a cisco pix 501 firewall with a cisco ASA 5505 firewall. I am not very familiar with all of the commands for the firewalls and have always relied on a standard command line script that I use when building a new one. Unfortunately, my script is not working with the 5505. What I am doing wrong with the following script? I've masked public IP info with xxx.xxx.xxx and I run it right after restoring the firewall to the factory defaults. I am able to get out to the internet if I browse directly from one of the servers, but cannot access a web page when trying to browse to it from an outside network. [code]
View 7 Replies
ADVERTISEMENT
Aug 30, 2011
I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
View 3 Replies
View Related
Oct 2, 2011
We have Cisco ASA 5505, 90.x.y.2/29 IP is assigned to outside interface. We have one internal HTTP server so that I use static (inside,outside) tcp interface [URL] to forward all incoming HTTP traffic to internal HTTP server 1. Now we need to add new physical HTTP server 2 so that I would like to forward
HTTP traffic to e.g. 90.x.y.3/29 to 172.16.0.11.
How can I do that? See scenario image (scenario.png) if needed.
View 6 Replies
View Related
Mar 6, 2013
I'm new to ASA's and PIX units. I've setup a few VPN's now but know next to nothing about logging on these units. I read the config guide for the PIX, but cannot figure out how to get a log of incoming SMTP traffic going on the console.Do I need to use a SYSLOG server? I can probably set one up on my laptop.
View 1 Replies
View Related
Dec 12, 2012
I was configure 3 interface on ASA1st - managemetn (only for management)2nd - gig0/0 is connected to internet with real IP3rd - gig0/1 is connected to local networkI was configure routed NAT to internet.But I have problem with restriction incomming traffic to inside interface (ifname is inside)but I can connect to ip address of inside interface from other ip. It is wrong and i can't understand where is my mistake.
View 2 Replies
View Related
May 15, 2012
Let me start by saying that I'm just starting to study for CCNA, so the ASA seems to be a bit above me yet. The ASA's we are using is for VPN to our corporate office and only allowing access to our Citrix environment, so no direct internet allowed. We have a person who works in the remote office who has need for a caption telephone that requires direct access to the internet. The phone only supports DHCP, and getting the ASA to do an ARP reservations is proving difficult. For now I wrote an access list to allow it's DHCP address out but it still isn't working. The access list I wrote is:
access-list 101 extended permit ip host xxx.xxx.xxx.124 any log
access-list 101 extended permit ip any any
access-group 101 out interface outside
When I do a show access-list I'm seeing that traffic is hitting the access list as the hit counter has increased. When I do a show conn I'm seeing one of the IP's that the phone should have access to, however the flags are: saA, so I'm assuming they are not getting a response. According to the manufacturer, only outbound connections are needed, no incoming ports required. All traffic is TCP.
View 8 Replies
View Related
Jul 3, 2012
We run a Cisco ASA 5510 and i need to find out how i can find the receving end on the inside of a vlan for traffic comming from outside.
ie incomming traffic on port 3937 and are NAT to eth 0/1.10
Thers a bunch of traffic on one port 33771 udp going in on 90.191.72.227 how do i trace this to the inside computer ???
lets say incomming traffic is on 90.191.72.227 and this is on eth0/0 this ip is NAT to a Vlan on the side for 10.10.0.0 with a subnet of 255.255.255.0
View 1 Replies
View Related
Mar 1, 2011
I ' m not able to configure the asa 5510 to allow the multicast traffic to pass through ASA.The multicast traffic have to pass from inside interface to outside interface.Can I configure the multicast traffic to pass through asa with a static nat ?
View 1 Replies
View Related
May 22, 2011
I have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
View 1 Replies
View Related
Dec 5, 2012
Since the power failure two days ago, my -ASA stops forwarding traffic to internal servers, for no apparent reason. Packet trace shows all OK, packet capture buffer stays empty when I try to http into the mail server. The only way to get it working is to change the Outside Ip to the one used for mail, then to change it back. It will work OK for a few hours, then stop, with nothing obvious in the logs.
View 2 Replies
View Related
Jun 13, 2012
I just got a Cisco asa 5505 with the next OS and ASDM info ASA 5505 OS 8.4(3) ASDM 6.47 I configured and enter all rules to allow incoming traffic to LAN but it's not working also, I have one host inside that is configured in a second IP and create the rule to allow traffic to it but it doesn't work too.
Problem 1 I have VNC running in port 5900 tcp and I want to connect from Internet using port 6001 and this has to forware the connection to the real VNC port. In the configuration I have a few host with the same configuration but I use different outside port to get it.
Problem 2. I have a second IP with services: SMTP, HTTP, HTTPS and port 444 all TCP forwarding to a server in the LAN.
Facts: SMTP. Every time that I do telnet to the second IP looking for the SMTP port, the firewall doesn't let the incoming connection goes through and the LOGGING screen doesn't how that connection.PORT 6001 (outside)this port is configured to work with the IP in the outside internface and it was to send the incoming connection to a host inside to the real port 5900.Can any one check my configuration if I'm missing anything? for sure I'm but I didn't find it. Bellow is the configuration, I masked the Public IPs just left the last number in the IP, also I left the LAN network to see better the configuration.
CONFIGURATION.
: Saved
:
ASA Version 8.4(3)
!
hostname saturn1
domain-name mydominio.com
enable password SOMEPASS encrypted
[code]....
View 4 Replies
View Related
Mar 4, 2013
We have a Cisco ASA 5520 and im looking for a way to monitor largest outgoing and incoming traffic per ip in real time so to know which of my internal computers are using the most of our Internet Line. Is there a way to this through ADSM ? We use version 6.3.
View 1 Replies
View Related
Apr 4, 2013
How to best troubleshoot some errors I'm seeing on the internal interfaces of my ASA 5505. This is similar to the question at [URL], but the details are different enough that I felt it justified a new discussion.
I have an ASA 5505, running version 8.2(2), 256MB RAM. From time to time (on the order of once a week) our monitoring alerts us that both Internal-Data0/0 and Internal-Data0/1 are experiencing an unusual amount of inbound packets which were discarded with errors, up to 2.3 per second as of this post. Here is what I hope relevant output from my device:
asa# show interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
Internal-Data0/1 unassigned YES unset up up
Vlan1 10.x.x.x YES CONFIG up up
Vlan2 32.32.32.32 YES CONFIG up up
[code]....
1. My understanding is that Internal-Data0/0 is an internal bus that connects to modules like the 4GE. I don't have any modules installed at all, as you can tell. Therefore, what is this bus doing?
2. For that matter, what is Internal-Data0/1 doing? What does it connect to?
3. I'm guessing that due to the input errors and overruns reported for both of these interfaces, it's a buffering issue. Since these are input errors, does this mean that traffic destined to this bus for forwarding is being dropped because the bus itself is running out of buffer memory? How would I see (and subsequently monitor) the buffer memory for these interfaces? Once I am able to see it, what sort of tools can I use to determine what is causing this?
View 3 Replies
View Related
Apr 24, 2012
I have a computer behind the ASA 5505 firewall. The computer needs to access Microsoft Activation Server. Reading some website information, I need to allow a huge list of servers that basically points to www and https traffic. Therefore, looking at this heavy requirements, I prefer to allow this computer to navigate to any https or http (www) server outside of the firewall.I have included my current asa 5505 configuration. [code]
View 3 Replies
View Related
Apr 24, 2012
I need to allow traceroute traffic through ASA running version 8.0.2.This traffic is natted. what configuration is required on ASA to allow this natted traceroute traffic.Traffic is coming from inside and going outside.Also can we capture this traceroute traffic on asa using capture feature.
View 12 Replies
View Related
Aug 20, 2012
I would like to block incoming traffic from a specific ip on a specific port
This is what I have
source: interface: wan ip address range: 5.xxx.xxx.226 - second one is empty (valid ip instead of x's) protocol: tcp
dest: interface: lan ip address range: both fields empty port range: 139 - empty field
ON and DENY box is ticked name field has some text in it
I click save and get this pop-up: Incorrect source ip address. Invalid format of the start IP address. Current Firmware Version : 2.11 The ip is obviously valid, what should I do?
View 1 Replies
View Related
Dec 5, 2012
I am able to ftp from my Head Office to my test machine at the remote location but I can't get the other way around to work. Error message from the Syslog deny tcp src 192.168.50.5/1825 dst 208.124.202.44/21 by access-group "dmz_access_in".I try a couple of ways to fix it but no luck.A partial config of my ASA 5505. [code]
View 4 Replies
View Related
Jul 24, 2011
We have a BT Infinity broadband circuit which terminates at a vdsl modem, I've plugged an ASA 5505 into the back of this modem and gone through the ADSM quick setup wizard (yes I'm that much of a beginner!) The config that's been generated is pasted below, the symptomns I'm seeing are;
The ASA is setup with PPPOE on the internet connection, I assume this is correct as if I do a show IP on the ASA I'm getting an IP address that has been assigned, if I change the password to the wrong one then I get no IP (as expected).
If I ping from the ASA to an internet connection I'm getting "no route" error messages, if I try a "ping outside x.x.x.x" then I get no repsonses.
The ASA can ping it's external IP, the client machines can ping it's internal, however nothing appears to be able to get out.
ASA Version 8.4(1)
!
hostname xxxxxx
enable password xxxxxx encrypted
[Code].....
View 15 Replies
View Related
Jul 10, 2011
We have the next Settings in our SW. We crate an ACL and aplied to a SVI for Incomming Traffic, I understand that is not necesasry to allow the returning traffic in ACL, but we can't access to rdp for example when we add the ACL, if we remove it, the acces is ok, buet when we add again the access is deny, even we have a log entry, and the ACL i just for Incomming traffic. There is no another ACL.
See attached file
[code]...
View 1 Replies
View Related
Feb 6, 2012
I have a licensing server. Other computers need to turn on a program, they send a message to the licensing server, and it responds that they have permission to run.Until today the licensing server was plugged into its own ethernet wall socket and configured with a static IP address. Today I put a router into that wall socket and now the server's plugged into the router.The router (WRT-54G) was set to the static IP - and now the internet on its network works. I set all ports to be forwarded to the server's internal IP address - and now my programs can detect and ping it. But now the server won't send back permissions to use licensed software, or even reply with a list of the software which it can license.
View 1 Replies
View Related
Apr 11, 2012
We have 110mbps internet service. When we have the 5505 behind the cable modem, our speed drops to 55mbps or so. If we remove the 5505, we see the full 100mbps. I assume the 5505 can handle the speed; if so, what other things should I be looking at?As an aside, we used to have 50mbps wich worked fine, then the ISP upgraded to 60mbps and the through put dropped to 30mbps (It always seems to be half)
View 2 Replies
View Related
Jun 25, 2012
My understanding is for insight to outside we need global and NAT, and for outside to inside we need static and ACL? Traffic goes to high to low, I'm just start working with 5505 recently.
View 2 Replies
View Related
Oct 27, 2011
I have VPN up and running between two sites. Both sites have Cisco ASA 5505. I can ping across the devices from both networks. But I cannot remote into the servers on the other network.
View 8 Replies
View Related
Aug 15, 2011
I have a Cisco ASA 5505 that I have configured. The outside interface is vlan 2 and the inside interface is vlan 1. Port 0 of the ASA is configured to be in vlan 2 and is connected to the ISP provided subnet. Port 1 is connected to my private LAN subnet. I have an additional router connected to Port 2 for guest connectivity. Port 2 is configured to be a member of VLAN 2 so that it can access the ISP provided subnet. From the device connected to port 2 I can ping the vlan 2 interface address of the ASA and from the ASA I can ping the Default gateway of the ISP provided subnet. For some reason the router on port 2 cannot ping the default gateway of the ISP provided subnet. If the vlan were working the same as a vlan in a switch, I would expect to be able to do this. why it is not working or what I can do to get it working?
View 4 Replies
View Related
May 24, 2011
I'm trying to allow SSH traffic from the Internet to my DMZ. I gave my remote guy my ip and he can see the ASA 5505 but not get into the DMZ. The outside is 70.165.19.137. The DMZ server is 192.168.60.2. I have the inside talking to the DMZ fine. [code]
View 9 Replies
View Related
Mar 10, 2013
I have a nac guest server 3315 appliance with 4 NICs. I want to connect each NIC to 4 different networks without allowing traffic between them. So RADIUS interface will be different from sponsor/admin interface to the NGS. how to achieve this. I have created and assigned a static IP address using system-config-network, but when i do ifconfig i dont see the remaining 3 NICs and the web interface doesnt seem to have provision to create this interfaces.
View 3 Replies
View Related
Apr 11, 2012
We have a switch gc2960. It has ports configured on vlan 27 and vlan 29.It is connected to switch ch3550. It has presence of vlan 27 vlan 29 and also vlan 18 and several other vlans.Our internet firewall is connected to ch3550. It is a fortinet product, so this is not indicated on the diagram.
When the two switches were connected on vlan 29 access ports, pc's on vlan 29 on gc2960 worked as expected. vlan 27 clients of course did not work.When we switched the connecting ports to trunk ports, some weird stuff happened. Clients on gc2960 on vlan 29 could ping and resolve dns, but not browse the intenet. The same was true for clients on gc2960 vlan 27. We verified that packets from the web were coming in through the firewall. What we were thinking, is that they somehow were not being tagged to vlan 29 even though we were trunking.
When we set native vlan 29 on the trunk, then clients on gc2960 vlan 29 operated as expected. However, clients on gc2960 vlan 27 are still having this problem, we can ping and resolve dns but not browse.Consider the other switch ch2960-jstreet which has presence of vlan 18 and vlan 27. It is also connected on trunk to ch3550. We are not using native vlan on this trunk, and traffic works as expected.Is the lack of presence of vlan 18 a factor as to why gc2960 is not receiving the tagged packets correctly? Should the interface vlan18 on gc2960 have an ip address on the vlan 18 network?
View 5 Replies
View Related
Jun 23, 2011
I need to block incoming traffic with Dlink DIR 600. I know how to create the rule source (WAN) to destination (LAN) to deny all protocols. But what IP will I put in WAN? IP address of my Internet? Or how can I enter the ALL IP range in source...format for the IP (it's not 0.0.0.0).
I want to do this because in the DIR log section I'm being PING Flooded. I already un-check "Enable WAN Ping Response" but still receiving the message.
View 4 Replies
View Related
Jun 13, 2012
I am fairly new to configuring ASA's. I have an ASA 5505 with one outside interface and three inside interfaces (inside1, inside2, and management). I need inside1 and inside2 to be able to talk to eachother but cannot work out how to make this happen. They are both configured to the same security level and the 'Enable traffic between interfaces with same security level' box is ticked. I have also tried adding appropriate NAT and Access rules. The packet tracer suggests the rules are correct for allowing traffic flow between interfaces but obviosly this may not be the case.
View 14 Replies
View Related
Jun 4, 2013
We have 10MB dedicated Internet BW and want to run VC device and due to heavy traffic and BW high utilization at peak hours, VC performance is not sufficient. We would like to reserve 2MB for VC device. How much possible to fix up this configuration in ASA5505 version disk0:/asa724-k8.bin [URL]
View 5 Replies
View Related
Jul 31, 2012
I have a Cisco 5505 with a 12Mbps feed. I want to reserve 2Mbps for RTP traffic. I followed the QoS guide here: url... The goal would be that any traffic destined for port 5000 through 5100 UDP or TCP from any IP to any IP on any interface.should always have 2Mbps available to it.
View 5 Replies
View Related
Oct 19, 2011
Is there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?
View 4 Replies
View Related
Oct 23, 2011
I've setup my Cisco ASA 5505 in transparent mode. I have a Cisco 1841 connecting to the ISP (DHCP client) and F0/0 for inside. The 1841 is the DHCP server. I have my ASA 5505 behind the 1841 in transparent mode (Vlan 1 for Outside and Vlan 1 for inside). The router config is good as when you connect a computer straight to the inside interface I get DHCP and can go to internet, no problems what so ever. But When you're trying to go through ASA isn't not working. if I add a ip any any statement to the access list it will work but having an "ip any any" in a access list is like having no firewall at all.
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(4)
!
firewall transparent
hostname ciscoasa
enable password zmQ6OnxvsOOEDNAy encrypted
[code]....
View 4 Replies
View Related
