I'm new to ASA's and PIX units. I've setup a few VPN's now but know next to nothing about logging on these units. I read the config guide for the PIX, but cannot figure out how to get a log of incoming SMTP traffic going on the console.Do I need to use a SYSLOG server? I can probably set one up on my laptop.
View 1 RepliesMost examples of NAT translation using an ASA 8.4 are based on servers within a DMZ. In my case it's not because the mailserver also functions as an data and Active Directory server for my local domain. If tried to config the ASA for a while now and throw it in the corner for a couple of months out of frustration. Now I got some time left during christmas break I decided to start again.My purpose is to NAT SMTP / POP traffic from the internet, trough the ASA to my (inside) server. This is what I got so far. With this config I'm unable to telnet the inside server (192.168.1.10) from a remote location.
ASA Version 8.4(3)!hostname ciscoasaenable password cE8UUNd encryptedpasswd 2KFQ.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 95.*.*.218 255.255.255.248!ftp mode passiveobject network obj_anysubnet 0.0.0.0 0.0.0.0object network server1_smtphost 192.168.1.10object network server1_pop3host 192.168.1.10access-list outside_access_in extended
[code]....
I can ping 192.168.1.10 from the ASA CLI. I can Ping DNS 4.2.2.2 from the CLI (internet access). I can Telnet the server from the inside LAN, using: telnet 192.168.1.10 25.But I can't Telnet from an outside location using: Telnet 95.*.*.218 25 Because my server is on the Inside interface (diffenrent subnet) do I need an additional route?
A recently added outbound rule has left my SMTP communications broken. I have since removed the rule, and had Cisco do some damage control, but it's still dropping some of the SMTP traffic. I get a number of NDR messages each day like the one below:Your message did not reach some or all of the intended recipients. Subject: RE: Christopher, Curt Sent: 8/19/2011 9:38 AM The following recipient(s) could not be reached:
[URL]
on 8/21/2011 9:49 AM
Could not deliver the message in the time limit specified. Please retry or contact your administrator.
<630.SM.Local #4.4.7>
Your message did not reach some or all of the intended recipients. Subject: RE: Christopher Curd Sent: 8/19/2011 9:38 AM The following recipient(s) could not be reached: JWillar@email.com on 8/21/2011 9:49 AM Could not deliver the message in the time limit specified. Please retry or contact your administrator. <630.SM.Local #4.4.7>
I've attached an image of my configuration (ASDM GUI). The part of the image highlighted in green are the SMTP rules. The part highlighted in yellow is another rule that I added about a month ago to block a SYN attack. This rule may be part of the problem because of the order it is in the list. Not sure, though.
I have had two Cisco techs Putty into my ASA to check things out. I think they've done all they can. I wonder at this point if it be wise to just reload the last good running-config I have prior to the Outbound rule being added.
Up until recently one of my sites was able to get to a postilion subnet. Then we started receiving "host unreachable" e-mails. Posting told us SMTP traffic was not getting let in. I've compared the current config to a config that was saved before the issue popped up and found really no noticeable difference.
I tried a packet tracer trace with no luck: SiteB- Firewall# packet-tracer input outside tcp 11.2.2.36 12345 65.19.0.0 25.
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
[code]...
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
Attached is a sanitized config. I'm not entirely convinced it's a firewall issue, but I need to some successful testing to prove otherwise.
I am trying to switch out a cisco pix 501 firewall with a cisco ASA 5505 firewall. I am not very familiar with all of the commands for the firewalls and have always relied on a standard command line script that I use when building a new one. Unfortunately, my script is not working with the 5505. What I am doing wrong with the following script? I've masked public IP info with xxx.xxx.xxx and I run it right after restoring the firewall to the factory defaults. I am able to get out to the internet if I browse directly from one of the servers, but cannot access a web page when trying to browse to it from an outside network. [code]
View 7 Replies View RelatedI was configure 3 interface on ASA1st - managemetn (only for management)2nd - gig0/0 is connected to internet with real IP3rd - gig0/1 is connected to local networkI was configure routed NAT to internet.But I have problem with restriction incomming traffic to inside interface (ifname is inside)but I can connect to ip address of inside interface from other ip. It is wrong and i can't understand where is my mistake.
View 2 Replies View Related\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
View 11 Replies View RelatedWe are using several Cisco ASA 5505 with the 8.05 OS on it. The problem is that the SMTP traffic of my ISP(Telenet) isn't passtrough the ASA, I'm using outlook 2010. Before there was also a problem with our local exchange server but I solved this by disabling ESMTP checking in the policies, but it didn't worked for my local ISP.
View 4 Replies View RelatedI am new to the ASA series and I am at a complete loss as to why I cannot configure this router to forward SMTP and RDP traffic to an internal host.
The packet trace tool in ASDM shows complete end-to-end connectivity for RDP but it still fails to connect from outside. This is my config file, what I need to change in order to make it work?
We run a Cisco ASA 5510 and i need to find out how i can find the receving end on the inside of a vlan for traffic comming from outside.
ie incomming traffic on port 3937 and are NAT to eth 0/1.10
Thers a bunch of traffic on one port 33771 udp going in on 90.191.72.227 how do i trace this to the inside computer ???
lets say incomming traffic is on 90.191.72.227 and this is on eth0/0 this ip is NAT to a Vlan on the side for 10.10.0.0 with a subnet of 255.255.255.0
Ive got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
theres a route to the inside net:
inside 172.16.0.0 255.255.0.0 172.16.163.1
and theres a translation:
static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
Since the power failure two days ago, my -ASA stops forwarding traffic to internal servers, for no apparent reason. Packet trace shows all OK, packet capture buffer stays empty when I try to http into the mail server. The only way to get it working is to change the Outside Ip to the one used for mail, then to change it back. It will work OK for a few hours, then stop, with nothing obvious in the logs.
View 2 Replies View RelatedWe have a Cisco ASA 5520 and im looking for a way to monitor largest outgoing and incoming traffic per ip in real time so to know which of my internal computers are using the most of our Internet Line. Is there a way to this through ADSM ? We use version 6.3.
View 1 Replies View RelatedI need to redo the configuration on the new one?
View 11 Replies View RelatedI use a mail filtering service that delivers mail to me via SMTP on standard port 25 on one of my 5 static external IP's. I wish to restrict this to their IP's only (they have two) and I am unsure on how to do so? As it stands now, anything on the net can talk to my mailserver and my logs are filling quickly with failed attempts as a result. Here's my setup and what I am trying to accomplish:
mail filtering service -> my public ip:25 -> internal mailserver at 10.0.10.2:25, deny everything inbound except traffic from the mail filtering service, I am thinking an ACL would fit the bill here, but unsure of how to implement. Router is an 1811 with version 15.1(4)M3 IOS. WAN is on fa0, lan is on fa1.
I would like to block incoming traffic from a specific ip on a specific port
This is what I have
source: interface: wan ip address range: 5.xxx.xxx.226 - second one is empty (valid ip instead of x's) protocol: tcp
dest: interface: lan ip address range: both fields empty port range: 139 - empty field
ON and DENY box is ticked name field has some text in it
I click save and get this pop-up: Incorrect source ip address. Invalid format of the start IP address. Current Firmware Version : 2.11 The ip is obviously valid, what should I do?
We have a customer using a 2911 router with 3 x DSL WAN links.
The customer runs a building with shared office space which people rent.
Customers in the building are experiencing a problem where they cant email other tenants i.e...
One tenants exchange server tries to make a connection to another tenants server by going out to the internet and back in via the same interface.I believe this might be called "Hair Pinning"
We have the next Settings in our SW. We crate an ACL and aplied to a SVI for Incomming Traffic, I understand that is not necesasry to allow the returning traffic in ACL, but we can't access to rdp for example when we add the ACL, if we remove it, the acces is ok, buet when we add again the access is deny, even we have a log entry, and the ACL i just for Incomming traffic. There is no another ACL.
See attached file
[code]...
I have a licensing server. Other computers need to turn on a program, they send a message to the licensing server, and it responds that they have permission to run.Until today the licensing server was plugged into its own ethernet wall socket and configured with a static IP address. Today I put a router into that wall socket and now the server's plugged into the router.The router (WRT-54G) was set to the static IP - and now the internet on its network works. I set all ports to be forwarded to the server's internal IP address - and now my programs can detect and ping it. But now the server won't send back permissions to use licensed software, or even reply with a list of the software which it can license.
View 1 Replies View RelatedWe have a switch gc2960. It has ports configured on vlan 27 and vlan 29.It is connected to switch ch3550. It has presence of vlan 27 vlan 29 and also vlan 18 and several other vlans.Our internet firewall is connected to ch3550. It is a fortinet product, so this is not indicated on the diagram.
When the two switches were connected on vlan 29 access ports, pc's on vlan 29 on gc2960 worked as expected. vlan 27 clients of course did not work.When we switched the connecting ports to trunk ports, some weird stuff happened. Clients on gc2960 on vlan 29 could ping and resolve dns, but not browse the intenet. The same was true for clients on gc2960 vlan 27. We verified that packets from the web were coming in through the firewall. What we were thinking, is that they somehow were not being tagged to vlan 29 even though we were trunking.
When we set native vlan 29 on the trunk, then clients on gc2960 vlan 29 operated as expected. However, clients on gc2960 vlan 27 are still having this problem, we can ping and resolve dns but not browse.Consider the other switch ch2960-jstreet which has presence of vlan 18 and vlan 27. It is also connected on trunk to ch3550. We are not using native vlan on this trunk, and traffic works as expected.Is the lack of presence of vlan 18 a factor as to why gc2960 is not receiving the tagged packets correctly? Should the interface vlan18 on gc2960 have an ip address on the vlan 18 network?
We have Cisco ASA 5505, 90.x.y.2/29 IP is assigned to outside interface. We have one internal HTTP server so that I use static (inside,outside) tcp interface [URL] to forward all incoming HTTP traffic to internal HTTP server 1. Now we need to add new physical HTTP server 2 so that I would like to forward
HTTP traffic to e.g. 90.x.y.3/29 to 172.16.0.11.
How can I do that? See scenario image (scenario.png) if needed.
I need to block incoming traffic with Dlink DIR 600. I know how to create the rule source (WAN) to destination (LAN) to deny all protocols. But what IP will I put in WAN? IP address of my Internet? Or how can I enter the ALL IP range in source...format for the IP (it's not 0.0.0.0).
I want to do this because in the DIR log section I'm being PING Flooded. I already un-check "Enable WAN Ping Response" but still receiving the message.
We had a problem with SMTP inspection dropping some regular emails (Cisco 2901 IOS 15.0). The original configuration.
View 2 Replies View RelatedWe had a problem with SMTP inspection dropping some regular emails (Cisco 2901 IOS 15.0).Incoming mails are going thru Spam and Virus Blocker so that bypassing SMTP inspection is not security issue in this case.
View 1 Replies View RelatedIOS Firewall (ZBF) Limit SMTP connections from same IP
we are running a Postfix MTA behind a IOS Firewall (ZBF) on a CISCO1921. Sometimes we get more than 2000 smtp login attemps like
postfix/smtpd[123456]: connect from (...) (...) postfix/smtpd[123456]: lost connection after AUTH from (...)
in one second. May be bruteforce or DoS ... nevertheless - we like to protect the Postfix MTA from this stuff.
Can we inspect the smtp and limit connections in a time period from the the same IP? Something like "not more than 10 smtp connections during 60 seconds from the same ip" .
I have an ASA 5500 Firewall. I need to figure out how to log all events using Port 25 to determine if there are any rogue devices on our network. I was trying to figure out how to do this via the Real-Time Monitoring (filter) but have had no success.
View 1 Replies View RelatedI am trying to configure my ASA5505 to allow SMTP relay and the ACLStatic I created is not working.
View 1 Replies View RelatedI have a ASA 5510 (ver 8.4) and I have been all over the support sites looking for what I am doing wrong. I have a sanitized cut n paste of the OBJECT, NAT, ACCESS-LIST and Packet Tracer output and it keeps failing on the NAT with a rpf-check. Once i get the SMTP flowing I have to open up HTTP and HTTPS to one of the servers also.
Here it is:
RVGW# sh run object
object network WiFi
subnet 172.17.100.0 255.255.255.0
[Code]......
Below is the interesting part of my config. I have static NAT configured and working inbound for the Exchange Server and the Barracuda, however outbound traffic from those hosts comes out as the interface IP. Thoughts? I've tried a number of things (outside, inside), etc.
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network DSN-EXCH01
host 10.250.231.51
object network MAIL-IN
host 10.250.231.50(code)
I need to move the email traffic to a backup circuit. Below is my config. I have tried for email access but to no avail.
asa5505# sho run
: Saved
:
ASA Version 8.2(2)
!
hostname asa5505
[code]........
I have an Pix 515E firewall with Pix724-33.bin IOS. I just want to know that does this IOS support SNMPV3 or I will have to upgarde it with some other version.
View 1 Replies View RelatedI am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....