Cisco Firewall :: Import PIX 515E 6.3(5) Config Into New PIX 515E 8.0?
Aug 22, 2011I need to redo the configuration on the new one?
View 11 Replies
ADVERTISEMENT
Cisco :: Pix 515e - Config VPN User Gateway
Apr 25, 2012I have pix 515e locate in office w/ IPSec VPN service ,that just for out of Office to access email
I wanna know how to config the VPN user thru the office Internet to access the web
Such I'm in china to access Facebook while I connected the VPN
Cisco Firewall :: PIX 515e MAC To IP?
Oct 6, 2012I have the following network.2 WAN links termination on my PIX 515e and all internal users connected to third interface.
Problem I am facing is that I have assign manual IP to users with some have full access to Internet while others have limited.
The users are changing their IP address while others are offline and I want to restrict them.
The only way I can think off is by binding IP to MAC as e.g ( Active wall software). But can it be done on PIX 515e and if so how?
Cisco Firewall :: To Get Activation Key For PIX 515E
May 13, 2012I have erased the Cisco image from my PIX 515E, and while i tried to load a new image its asking for activation key. I tried its old key. but no use.
View 1 Replies View RelatedCisco Firewall :: SSH Authentication In PIX 515E?
Sep 5, 2012I have a PIX 515 Ewhich does authentication for SSH via RADIUS protocol and fails over to the local database if radius server goes offline. But when the radius server comes back online, authentication still takes place through LOCAL and not the radius server. Following are the commands:
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
[Code].....
Cisco Firewall :: PIX 515E Cannot Get Traffic Out
Dec 15, 2011\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
View 11 Replies View RelatedCisco Firewall :: NFS Protocol Across Pix 515E
Dec 30, 2011I have a Pix 515E running PixOS version 8.0.4 with two interfaces, inside and outside.On the inside interface, I have a Redhat Enterprise Linux 5.4 64 bits machine as an NFS server version 4 (NFSv4).On the outside interface, I have three (3) Redhat Enterprise Linux 5.4 64 bits as NFS clients.I am looking for the exact UDP and TCP ports to be added to the ACL in order to accomplish
View 1 Replies View RelatedCisco Firewall :: Upgrading Pix 515E To ASA
May 15, 2012I need ot upgrade a Cisco PIX 515 E to A Cisco ASA (not sure what type and modle yet!). the PIX currently has about 80 lines of ACLs and no VPNs. So only inside and outside interfaces and 80 lines of ACLs to be transferred over to the ASA.I was wondering if the ACLs can be transferred over to ASA as is?is there anything that I need ot watch for?
View 1 Replies View RelatedCisco Firewall :: TCP Tear-down In Pix 515e
Jun 30, 2011I have an issue in the Cisco PIx 515e series. The IOS is 6.1(2).I have set sepecific access-list to allow incoming traffic to inside interface. But still the TCP 3-way handshaking is dropped here. [code]
View 6 Replies View RelatedCisco Firewall :: How To Allow Protocol 97 In PIX 515E
Oct 22, 2012What would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.
View 1 Replies View RelatedCisco Firewall :: Pix 515E Could Configure The Device
Oct 2, 2012We just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedCisco Firewall :: PIX 515E Port Redirection?
Nov 30, 2011I'm trying to use port redirection to allow outside access to a internal web server. As far as I can see, everything is configured properly. The Open Port Checker tool from yougotsingle.com says that the port (80) is open. However when I goto access it the connection times out. The external address is static from my ISP, and I will call it xxx.xxx.xxx.xxx. The server is at 10.1.1.20, and is functioning properly over the LAN.
View 7 Replies View RelatedCisco Firewall :: How To Reset PIX 515E Password
Mar 29, 2011I have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedCisco Firewall :: ASDM 524 Not Working On PIX 515e 7.2.4(30)
May 21, 2012I've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
show run
: Saved
:
[Code]....
Cisco Firewall :: PIX 515E Stop Booting Up?
Sep 18, 2011I have the following Pix 515E Firewall, that has been working good for a few years. But suddenly, the Pix stop booting up. The only thing that is happening is the power and network traffic led flashes and the active led is off. So my question is that is this symptom a hardware or software problem and is it fixable with either new parts; or is my firewall dead. I suspect that it is a hardware problem since the active led doesn't light up. I cann't even enter the ROM Moniter mode.
View 7 Replies View RelatedCisco Firewall :: Clearing DF-bit On PIX-515e Running 6.3
Feb 16, 2012What would be the command to clear the df-bit on a PIX-515e running 6.3? I have tried the following:
conf t crypto ipsec df-bit clear-df inside and it doesn't take it.
Cisco Firewall :: High Cpu Utilization On Pix 515E?
Aug 9, 2012I am facing high CPU util on my pix 515 E which is in failover mode.During peak hours the util is see rising to 60% where as in off peak hours it is normally12%.
During normal operation the average utilisation was observed to be 30% but suddenly from 2/3 days it is constantly 60% doule the value as earlier. Have gone through the logs and traffic but not able to tarce anything particular
below is the o/p of some command taken for analysis
IOS version 8.0(4)
sh cpu usage
CPU utilization for 5 seconds = 51%; 1 minute: 61%; 5 minutes: 58%
sh cpu usage
[Code]......
Cisco Firewall :: PIX 515E 6.3.3 - DMZ Creation Doubts
Jul 26, 2011I need to create a DMZ zone in my network. One server need to be put in DMZ. I have a PIX 515E 6.3.3. It has free port to create DMZ.
1) Put a new switch for DMZ zone
2) Connect it to the DMZ port
3) Create a NAT for inside to DMZ with same IP as inside
4) Create ACL for permiting traffic to DMZ and apply it to outside interface
5) Create ACl for permitting traffic from DMZ to inside
6) Routing for DMZ in PIX
Cisco Firewall :: PIX 515E To ASA5515 Migration?
Aug 26, 2012Looking at migrating from the following:
PIX-515EPIX Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)51
to
ASA5515Cisco Adaptive Security Appliance Software Version 8.6(1)Device Manager Version 6.6(1)
Is this migration directly supported, or do I need to downgrade first?
Cisco Firewall :: Pix-515E Possible To Even Get Access To That Version
Jul 1, 2011I was wondering if I picked up a used (End of Life) pix-515e, would would I need to do to be able to upgrade it to that latest version of IOS made for that product? Is it still possible to even get access to that version? Will cisco allow downloads for that devices IOS?
View 4 Replies View RelatedCisco Firewall :: Upgrade Firmware On PIX 515e?
Jun 23, 2011I´ve a problem with my "old" PIX515e device. I wanted to flash this device to a new firmware level but forgot to disable the "lost enable" password before. So I started to make the firmware upgrade on my device, ended up with "flashfs" is busy and I should start the enabled modus and "copy flash tftp" to activate the new flash version. Unfortunalty I cannot do this because I´ve lost my password. When I´m trying to boot this device up now, it will end with a error message...
Unable to locate boot image configuration
Booting first image in flash
No bootable image in flash. Please download an image from a network server in the monitor mode
Failed to find an image to boot
As mentioned, when I will load a new flash image over monitor mode, i cannot activate that image because of flashfs is busy.The password reset bin files will not work too. I tried that too but this one will recongnize no active installed flash.Is there any way to reanimate my PIX515e? In newer devices there are possibilites to work with changing config register but I´ve found nothing about that for a PIX515e.
Cisco Firewall :: Upgrade / Replace 515E With ASA
May 15, 2012I need to upgrade/ replace a Cisco 515 E firewall with a Cisco ASA. Not sure what model yet! The pix has about 80 lines of ACLs and I side and outside interfaces with No VPNs.. I was wondering of those lines of ACLs can be transferred over to ASA as is or there are things I need to watch for ?
View 21 Replies View RelatedCisco Firewall :: Pix 515e Basic CLi Configuration
Oct 12, 2011I dint have any experience in Using cisco pix firewall. i got this for home lab practice.the pix can be accessed and configured by web based and CLI mode right. basic configuariton tto configure pix 515e in cli mode.
as of now im using console( hyper terminal) to access the pix. in cli based commands i need the following
1. how to assign ip address to inside ethernet and outside ethernet
2. how to enable telnet and after enabling it , can i connect my pc directly to the pix inside ethernet and do telnetting or if at all possible with (https enabled)web based config. any of these are ohk.
went at browsing to find these all i could find is web based configs. i need cli commands.
Cisco Firewall :: PIX 515e Port Forwarding
Apr 2, 2012I'm having issues both with port forwarding and VPN with my PIX. I've tried different ways to set up port forwarding for remote desktop, but I still haven't had any luck.
With the VPN, I can secure a connection into the PIX, but I cannot access the internet or ping any of my devices on the remote network.
hostname PIX-515E-1
domain-name #####
enable password ##### encrypted
passwd ##### encrypted
names(code)
Cisco Firewall :: Pix 515E Free Memory Very Low
Mar 29, 2013My Pix seems to have a memory leak ?
Result of the command: "sh memory"
Free memory: 6088072 bytes ( 9%)
Used memory: 61020792 bytes (91%)
------------- ----------------
Total memory: 67108864 bytes (100%)
This is 30mins after a restart. Seem like it gets worse and worse until i cant even connect to the ASDM.
I have Tried turning off loggin as well as some connection timeout commands.
Cisco Firewall :: PIX 515e Reason To Upgrade To ASA Cluster
Feb 24, 2011Just looking for some good reasons why I should upgrade a Cisco PIX 515e cluster to an ASA Cluster to present to the business.
View 1 Replies View RelatedCisco Firewall :: PIX 515E Discovering Isakmp Key For Those Vpn Tunnels
May 10, 2011We have a PIX firewall 515E running version 6.3(4) and there are few site to site VPN's installed on it. We want to find out the isakmp key for those VPN tunnels. On ASA, We can run the command "more system..." and it displays the key, but it seems it doesn't work on the PIX 515E.
View 1 Replies View RelatedCisco Firewall :: Changing PIX 515E Failover Interface IPs?
Mar 6, 2011I am looking to change my Failover Int IPs on my PIX 515E Bundle, Cisco PIX Firewall Version 6.3(5)123 with the least impact on the network.
For example:
interface ethernet5 "state"
IP address 172.18.0.245, subnet mask 255.255.255.252
ip address state 172.18.0.245 255.255.255.252
failover ip address state 172.18.0.246
I want to change these lines to .....
interface ethernet5 "state"
IP address 172.18.0.185, subnet mask 255.255.255.252
ip address state 172.18.0.185 255.255.255.252
failover ip address state 172.18.0.186
Cisco Firewall :: How To Log Incoming Traffic (SMTP) On PIX 515E
Mar 6, 2013I'm new to ASA's and PIX units. I've setup a few VPN's now but know next to nothing about logging on these units. I read the config guide for the PIX, but cannot figure out how to get a log of incoming SMTP traffic going on the console.Do I need to use a SYSLOG server? I can probably set one up on my laptop.
View 1 Replies View RelatedCisco Firewall :: PIX 515E Unable To Ping Outside From Inside
Dec 1, 2012I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0
Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.
Cisco Firewall :: Pix 515E To Wipe Clean And Get Rid Of Failover
Apr 16, 2012Is there a way to wipe a 515e clean and get ride of the Failover Only license and just have a basic licesne loaded? I got this off of ebay and I guess I missed where it said Failover Only, and I would really like to use it.
View 2 Replies View RelatedCisco Firewall :: Way On Pix 515E To Have One Internet Provider Be Preferred Over Other
Jul 6, 2011in a week or two we are going to put in a secondary internet connection. Is there a way on a pix 515E to have one internet provider be preferred over the other and if the primary fails then the secondary will take over?
View 3 Replies View RelatedCisco Firewall :: PIX 515E Reset To Factory Default?
Jul 3, 2011Im connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
View 11 Replies View Related
