I was wondering if I picked up a used (End of Life) pix-515e, would would I need to do to be able to upgrade it to that latest version of IOS made for that product? Is it still possible to even get access to that version? Will cisco allow downloads for that devices IOS?
View 4 RepliesHow can I configure the Cisco 515E (version 6.3(4)) to be used with ADSL modem. Currently the compuerters are directly connected to the ADSL modem to get the priviate IP addresses and we would like to add the Cisco firewall after the ADSL modem.
ADSL Modem ---> Firewall --> Switch--> Computers
I need to redo the configuration on the new one?
View 11 Replies View RelatedPix 515e 6.3.4..A web server on our DMZ is exposed for external access.There is an "A" record (webserver.yyy) on a public DNS for this public IP.This works fine for external users. url..Now I have been asked to allowed our LAN user to access the same link and I CANNOT CREATE AN INTERNAL DNS RECORD TO TAKE CARE OF THIS, which means when our internal users access that link, the request goes out of OUTSIDE interface with a NAT overloaded address(111.111.111.2) that is in the same subnet as the URL is trying to resolve. Once it knows the IP address thru DNS resolution tries to comes back in thru the same Interface(OUTSIDE) to hit the web server in the DMZ and is not able to.
1- Where does the request from an internal user to hit url is dropped?
2- what can be done to allow this type of connectivity in the PIX 515e device?
I have a tunnel between a PIX 515E version 7.2(2)and a Cisco 3800 version 12.3(11r). There is a mismatch somewere in the configs but I cannot find it. I have included the configs and the syslog errors.
View 5 Replies View RelatedI have a PIX-515E version 8.0(2).I have two remote sites connected to this PIX via IPSec tunnels.Each remote site can reach the local networks behind the PIX but I can not reach remoteSiteA from remoteSiteB.So,
10.30.8.254 SiteA <----- IPSec -----> PIX1 <----------------> SiteX 10.0.8.1
10.138.34.21 SiteB <----- IPSec -----> PIX1 <----------------> SiteX 10.0.8.1
SiteA can ping SiteX
SiteB can ping SiteX
SiteA can't ping SiteB
SiteB can't ping SiteA
If i do show crypto isakmp ipsec sa I can see appropriate subnets:
Crypto map tag: CRYPTO-MAP, seq num: 4, local addr: 203.166.1.1
access-list ACLVPN-TO_SITEA permit ip 10.138.34.16 255.255.255.240 host 10.30.8.254
local ident (addr/mask/prot/port): (10.138.34.16/255.255.255.240/0/0)
remote ident (addr/mask/prot/port): (10.30.8.254/255.255.255.255/0/0)
current_peer: 104.86.2.4
[code]....
Some log messages that seem to point to the problem...
Apr 18 2013 13:27:35: %PIX-4-402116: IPSEC: Received an ESP packet (SPI= 0xD51BB13A, sequence number= 0x21A) from 104.86.2.4 (user= 104.86.2.4) to 203.166.1.1. The decapsulated inner packet doesn't match the negotiated policy in the SA. The packet specifies its destination as 10.138.34.21, its source as 10.30.8.254, and its protocol as 6. The SA specifies its local proxy as 10.0.8.0/255.255.255.0/0/0 and its remote_proxy as 10.30.8.254/255.255.255.255/0/0
My question is really do I need to do anything funky to allow the traffic to pass between the two tunnels?
I've have an ASA 5505 with a inside network vlan1 (192.168.0.0/24) - i've configured an IPsec VPN profile and a VPN network of 192.168.0.50/24. I can through my VPN tunnel access inside hosts on vlan1 - but not ASDM on the ASA (192.168.0.1). Under management i've added the VPN network of 192.168.50.0/24 to have access to ASDM, but still does not work.
View 1 Replies View RelatedI am not able to access asdm via my browser. All is setup correctly that I can see. Here is my config
ASA Version 8.6(1)2
!
hostname DFB-ASA
enable password YWZBogZjbyvTSYf1 encrypted
passwd YWZBogZjbyvTSYf1 encrypted
names
!
interface GigabitEthernet0/0
[code]....
provide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View RelatedI am trying to remove a line in a particular access-list configured in a FWSM module using this command "no access-list <acl> line 19 x x x x" but it doesn't work. See below:
FWSM/xxx03(config)# no access-list ?
configure mode commands/options:
alert-interval Specify the alert interval for generating syslog message
106001 which alerts that the system has reached a deny
[code]...
How can I remove a line from the access-list without clearing the entire access-list?
i am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedI have an Pix 515E firewall with Pix724-33.bin IOS. I just want to know that does this IOS support SNMPV3 or I will have to upgarde it with some other version.
View 1 Replies View RelatedIve got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
theres a route to the inside net:
inside 172.16.0.0 255.255.0.0 172.16.163.1
and theres a translation:
static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....
I have Pix firewall 515e on inside interface its has configured with IP 192.168.0.254.And Global Nating is configured.
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.255.0 0 0
I want i configured Global nating only for only specific IP address E.g 192.168.0.0-192.168.0.30 and 192.168.0.200-192.168.0.254?How i do this?
I have the following network.2 WAN links termination on my PIX 515e and all internal users connected to third interface.
Problem I am facing is that I have assign manual IP to users with some have full access to Internet while others have limited.
The users are changing their IP address while others are offline and I want to restrict them.
The only way I can think off is by binding IP to MAC as e.g ( Active wall software). But can it be done on PIX 515e and if so how?
I have erased the Cisco image from my PIX 515E, and while i tried to load a new image its asking for activation key. I tried its old key. but no use.
View 1 Replies View RelatedI have a PIX 515 Ewhich does authentication for SSH via RADIUS protocol and fails over to the local database if radius server goes offline. But when the radius server comes back online, authentication still takes place through LOCAL and not the radius server. Following are the commands:
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
[Code].....
\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
View 11 Replies View RelatedI have a Pix 515E running PixOS version 8.0.4 with two interfaces, inside and outside.On the inside interface, I have a Redhat Enterprise Linux 5.4 64 bits machine as an NFS server version 4 (NFSv4).On the outside interface, I have three (3) Redhat Enterprise Linux 5.4 64 bits as NFS clients.I am looking for the exact UDP and TCP ports to be added to the ACL in order to accomplish
View 1 Replies View RelatedI need ot upgrade a Cisco PIX 515 E to A Cisco ASA (not sure what type and modle yet!). the PIX currently has about 80 lines of ACLs and no VPNs. So only inside and outside interfaces and 80 lines of ACLs to be transferred over to the ASA.I was wondering if the ACLs can be transferred over to ASA as is?is there anything that I need ot watch for?
View 1 Replies View RelatedI have an issue in the Cisco PIx 515e series. The IOS is 6.1(2).I have set sepecific access-list to allow incoming traffic to inside interface. But still the TCP 3-way handshaking is dropped here. [code]
View 6 Replies View RelatedWhat would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.
View 1 Replies View RelatedWe just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedI'm trying to use port redirection to allow outside access to a internal web server. As far as I can see, everything is configured properly. The Open Port Checker tool from yougotsingle.com says that the port (80) is open. However when I goto access it the connection times out. The external address is static from my ISP, and I will call it xxx.xxx.xxx.xxx. The server is at 10.1.1.20, and is functioning properly over the LAN.
View 7 Replies View RelatedI have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedI've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
show run
: Saved
:
[Code]....
I have the following Pix 515E Firewall, that has been working good for a few years. But suddenly, the Pix stop booting up. The only thing that is happening is the power and network traffic led flashes and the active led is off. So my question is that is this symptom a hardware or software problem and is it fixable with either new parts; or is my firewall dead. I suspect that it is a hardware problem since the active led doesn't light up. I cann't even enter the ROM Moniter mode.
View 7 Replies View RelatedWhat would be the command to clear the df-bit on a PIX-515e running 6.3? I have tried the following:
conf t crypto ipsec df-bit clear-df inside and it doesn't take it.
I am facing high CPU util on my pix 515 E which is in failover mode.During peak hours the util is see rising to 60% where as in off peak hours it is normally12%.
During normal operation the average utilisation was observed to be 30% but suddenly from 2/3 days it is constantly 60% doule the value as earlier. Have gone through the logs and traffic but not able to tarce anything particular
below is the o/p of some command taken for analysis
IOS version 8.0(4)
sh cpu usage
CPU utilization for 5 seconds = 51%; 1 minute: 61%; 5 minutes: 58%
sh cpu usage
[Code]......
I need to create a DMZ zone in my network. One server need to be put in DMZ. I have a PIX 515E 6.3.3. It has free port to create DMZ.
1) Put a new switch for DMZ zone
2) Connect it to the DMZ port
3) Create a NAT for inside to DMZ with same IP as inside
4) Create ACL for permiting traffic to DMZ and apply it to outside interface
5) Create ACl for permitting traffic from DMZ to inside
6) Routing for DMZ in PIX
Looking at migrating from the following:
PIX-515EPIX Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)51
to
ASA5515Cisco Adaptive Security Appliance Software Version 8.6(1)Device Manager Version 6.6(1)
Is this migration directly supported, or do I need to downgrade first?
I´ve a problem with my "old" PIX515e device. I wanted to flash this device to a new firmware level but forgot to disable the "lost enable" password before. So I started to make the firmware upgrade on my device, ended up with "flashfs" is busy and I should start the enabled modus and "copy flash tftp" to activate the new flash version. Unfortunalty I cannot do this because I´ve lost my password. When I´m trying to boot this device up now, it will end with a error message...
Unable to locate boot image configuration
Booting first image in flash
No bootable image in flash. Please download an image from a network server in the monitor mode
Failed to find an image to boot
As mentioned, when I will load a new flash image over monitor mode, i cannot activate that image because of flashfs is busy.The password reset bin files will not work too. I tried that too but this one will recongnize no active installed flash.Is there any way to reanimate my PIX515e? In newer devices there are possibilites to work with changing config register but I´ve found nothing about that for a PIX515e.