I need to move the email traffic to a backup circuit. Below is my config. I have tried for email access but to no avail.
asa5505# sho run
: Saved
:
ASA Version 8.2(2)
!
hostname asa5505
[code]........
i cannot send emails to outside, i have an access rule on interface inside permit source: inside destination: any servic: tcp/smtp and when i make paket tracer it shows me that the packet is dropped but i cant see through which rule!!
ASA version: 8.4(3)
ASDM version 6.4(7)
We are using several Cisco ASA 5505 with the 8.05 OS on it. The problem is that the SMTP traffic of my ISP(Telenet) isn't passtrough the ASA, I'm using outlook 2010. Before there was also a problem with our local exchange server but I solved this by disabling ESMTP checking in the policies, but it didn't worked for my local ISP.
View 4 Replies View RelatedUsing an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
This is my first post in CSC. I have two issues with ASA 5505. I have configured ASA to use Easy vpn (ASA as RA server). Users are able to connect to vpn with out any issue and there is no diconnections with VPN. But when the users are trying to RDP to server it connects and disconnect as soon as login. some time it connect for 2 mins then it fades out for some time then it reconnects again. I guess I have give correct access-lists. Please find the Running configuration in the below.
2). we have a Email server in DMZ zone and it users are able to connect to the email server and they can see the emails. But when they try to send any emails it just stuck in the email server queue and does not deliver to the destination.
ASA Version 7.2(3)
!
!
interface Vlan1
nameif inside
security-level 100
ip address intinside 255.255.255.0
[code]....
We had a problem with SMTP inspection dropping some regular emails (Cisco 2901 IOS 15.0). The original configuration.
View 2 Replies View RelatedWe had a problem with SMTP inspection dropping some regular emails (Cisco 2901 IOS 15.0).Incoming mails are going thru Spam and Virus Blocker so that bypassing SMTP inspection is not security issue in this case.
View 1 Replies View RelatedIOS Firewall (ZBF) Limit SMTP connections from same IP
we are running a Postfix MTA behind a IOS Firewall (ZBF) on a CISCO1921. Sometimes we get more than 2000 smtp login attemps like
postfix/smtpd[123456]: connect from (...) (...) postfix/smtpd[123456]: lost connection after AUTH from (...)
in one second. May be bruteforce or DoS ... nevertheless - we like to protect the Postfix MTA from this stuff.
Can we inspect the smtp and limit connections in a time period from the the same IP? Something like "not more than 10 smtp connections during 60 seconds from the same ip" .
I have an ASA 5500 Firewall. I need to figure out how to log all events using Port 25 to determine if there are any rogue devices on our network. I was trying to figure out how to do this via the Real-Time Monitoring (filter) but have had no success.
View 1 Replies View RelatedI am trying to configure my ASA5505 to allow SMTP relay and the ACLStatic I created is not working.
View 1 Replies View RelatedMost examples of NAT translation using an ASA 8.4 are based on servers within a DMZ. In my case it's not because the mailserver also functions as an data and Active Directory server for my local domain. If tried to config the ASA for a while now and throw it in the corner for a couple of months out of frustration. Now I got some time left during christmas break I decided to start again.My purpose is to NAT SMTP / POP traffic from the internet, trough the ASA to my (inside) server. This is what I got so far. With this config I'm unable to telnet the inside server (192.168.1.10) from a remote location.
ASA Version 8.4(3)!hostname ciscoasaenable password cE8UUNd encryptedpasswd 2KFQ.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 95.*.*.218 255.255.255.248!ftp mode passiveobject network obj_anysubnet 0.0.0.0 0.0.0.0object network server1_smtphost 192.168.1.10object network server1_pop3host 192.168.1.10access-list outside_access_in extended
[code]....
I can ping 192.168.1.10 from the ASA CLI. I can Ping DNS 4.2.2.2 from the CLI (internet access). I can Telnet the server from the inside LAN, using: telnet 192.168.1.10 25.But I can't Telnet from an outside location using: Telnet 95.*.*.218 25 Because my server is on the Inside interface (diffenrent subnet) do I need an additional route?
I have a ASA 5510 (ver 8.4) and I have been all over the support sites looking for what I am doing wrong. I have a sanitized cut n paste of the OBJECT, NAT, ACCESS-LIST and Packet Tracer output and it keeps failing on the NAT with a rpf-check. Once i get the SMTP flowing I have to open up HTTP and HTTPS to one of the servers also.
Here it is:
RVGW# sh run object
object network WiFi
subnet 172.17.100.0 255.255.255.0
[Code]......
Below is the interesting part of my config. I have static NAT configured and working inbound for the Exchange Server and the Barracuda, however outbound traffic from those hosts comes out as the interface IP. Thoughts? I've tried a number of things (outside, inside), etc.
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network DSN-EXCH01
host 10.250.231.51
object network MAIL-IN
host 10.250.231.50(code)
I'm new to ASA's and PIX units. I've setup a few VPN's now but know next to nothing about logging on these units. I read the config guide for the PIX, but cannot figure out how to get a log of incoming SMTP traffic going on the console.Do I need to use a SYSLOG server? I can probably set one up on my laptop.
View 1 Replies View RelatedI'm trying to configure a simple ACL to block smtp traffic from leaving my LAN -- basically prevent internal users from setting up internet email accounts in their email clients and sending through that smtp server. i want my Exchange server only to send smtp traffic. here's what i have:
-access-list 102 extended permit tcp host 10.10.1.29 eq smtp any eq smtp <===10.10.1.29 is Exchange
-access-list 102 extended deny tcp any eq smtp any eq smtp
-access-list 102 extended permit ip any any
-access-group 102 in interface inside
after i apply this ACL to the ASA, i am still able to send from my internet email address setup in Outlook using my "foreign" smtp server.
I have an issue with my mail server(SME Server) which is behind a Cisco ASA 5500(firewall) problem is that if one leaves my network they can receive but can not send email via my SMTP also internal people can only send if they use the IP address of the server rather than the domain [URL]
here is my layout
ISP - ASA 5510 - LAN (includes mailserver)
We have hosted spam filter service with 3rd party vendor. My vendor is switching to different spamming services and I need to add ip address lets say 44.33.454.32 to the list of allowed system that can connect to my smtp service. I am going over my firewall 5510 configs and I think I need add the entry like this: “access-list outside-to-inside extended permit tcp object-group obj-44.33.454.32 interface outside eq smtp”. [code]
View 2 Replies View RelatedWe have an ASA5510 with the IPS ASA-SSM-10 module installed. All is working well except event notification. When sending a test email from the SSM IPS, we get the error "could not connect to SMTP host". The Exchange SMTP host does allow traffic from the IPS and ASA. I can ping to the SMTP host by IP and name. What am I missing here?
View 3 Replies View RelatedJust doing some basic testing before we replace our ancient PIX 515E with a new 5512. I have a mini lab set up following the diagram below, although I am unable to telnet through to the mail server's netcat listener on port 25 TCP. I can ping all the way outbound from 192.168.101.1 to 10.0.0.2, and the 10.0.0.2 machine shows it is translated properly to 200.225.117.1.
NAT and access rules are as follows:
object network mail
host 192.168.101.1
description Mail relay
access-list inbound extended permit ip any host 200.225.117.1
[code]....
EDIT: Somehow the new global access rule is involved. When adding a permit any any in there I can get to the mail server no problem. When I remove it but leave in my permit ip any any on the outside interface, I am denied?
We have a 5510 (8.2) with the following 4 interfaces (security-levels) inside (95), outside(0), dmz(25), and test (95). The dmz network is 10.10.10.0/24 and the outside interface is 40.133.84.69.We have run into a situation where a dmz hosted iRedMail server running postfix (10.10.10.51) is relaying mail which in some cases points back to us at 40.133.84.69 and into our Exchange server. In these cases in the dmz server's mail logs we see postfix timeout trying to connect to smtp at 40.133.84.69. When I try to telnet from 10.10.10.51 to the outside interface on port 25 it times out.We've tried different ways to allow the outside adapter to permit smtp (or any service!) from 10.10.10.51 but we're left scratching out heads.
View 1 Replies View Relatedhow to go about setting up the ASA to block any SMTP traffic outbound except for our Exchange Server. This is in relationship to a SpamBot issue that blacklisted us. I have an ASA 5510 running version 6.2(5) / 8.2(2) with three ports. DMZ, Inside and the Outside interface. Up till today, I only needed to block outside traffic to our internal network which I used the ASDM to configure a rule on the outside interface for an incoming rule. I am assuming I need to create an outgoing rule on the outside interface; however, just to make sure I understand the terminology/traffic flow, I created the rule with my computer as the source (192.168.0.131) with ALL destination and the service as HTTP. My logic, which seems to fail here, is that any traffic from my computer going outbound would be blocked; however I am still able to browse... That said, if I were to change the source as the Exchange server and the Service Type to SMTP, it would not actually block traffic and therefore not solve our problem. I even gone as far as permitting traffic from my computer, expanding the hit counter and I see no hits. So I am no doubt doing this wrong. What I do know, is when I first created the rule, a second rule was automatically created (Implicit rule) that deny all sources and blocked all HTTP traffic until I changed it to Permit?
View 2 Replies View RelatedA recently added outbound rule has left my SMTP communications broken. I have since removed the rule, and had Cisco do some damage control, but it's still dropping some of the SMTP traffic. I get a number of NDR messages each day like the one below:Your message did not reach some or all of the intended recipients. Subject: RE: Christopher, Curt Sent: 8/19/2011 9:38 AM The following recipient(s) could not be reached:
[URL]
on 8/21/2011 9:49 AM
Could not deliver the message in the time limit specified. Please retry or contact your administrator.
<630.SM.Local #4.4.7>
Your message did not reach some or all of the intended recipients. Subject: RE: Christopher Curd Sent: 8/19/2011 9:38 AM The following recipient(s) could not be reached: JWillar@email.com on 8/21/2011 9:49 AM Could not deliver the message in the time limit specified. Please retry or contact your administrator. <630.SM.Local #4.4.7>
I've attached an image of my configuration (ASDM GUI). The part of the image highlighted in green are the SMTP rules. The part highlighted in yellow is another rule that I added about a month ago to block a SYN attack. This rule may be part of the problem because of the order it is in the list. Not sure, though.
I have had two Cisco techs Putty into my ASA to check things out. I think they've done all they can. I wonder at this point if it be wise to just reload the last good running-config I have prior to the Outbound rule being added.
Up until recently one of my sites was able to get to a postilion subnet. Then we started receiving "host unreachable" e-mails. Posting told us SMTP traffic was not getting let in. I've compared the current config to a config that was saved before the issue popped up and found really no noticeable difference.
I tried a packet tracer trace with no luck: SiteB- Firewall# packet-tracer input outside tcp 11.2.2.36 12345 65.19.0.0 25.
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
[code]...
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
Attached is a sanitized config. I'm not entirely convinced it's a firewall issue, but I need to some successful testing to prove otherwise.
I 've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).Some Users received in there mailbox a system administor error message :Object : Impossible to deliver : testYour message could not be deliver to one or more of its recipients: 421 SMTP connection went away!When they try to re sent it some times later, message is sent whithout problem.
View 3 Replies View RelatedI am new to the ASA series and I am at a complete loss as to why I cannot configure this router to forward SMTP and RDP traffic to an internal host.
The packet trace tool in ASDM shows complete end-to-end connectivity for RDP but it still fails to connect from outside. This is my config file, what I need to change in order to make it work?
I have an ASA 5510, one public IP address on my outside interface, an internal email server and a private network.I would like...
1: Users on my private network to be able to access the internet (PAT them to external outside address)
2: Email to be delivered to my MX (my single public IP address translated back to my internal email server.
i.e. can I share my single public IP address to serve translation in both directions (private users surfing the Internet (in-to-out) and an outside to inside NAT for email) ?
Email (MX) = 1.2.3.4
Public (outside) address = 1.2.3.4
Email server internal = 10.1.2.3
Internal private subnet for users = 10.0.0.0/8
I can't access our ASA 5505 via SSH from the outside. I've configured this through the ASDM to allow SSH (Device Management > Management Access > ASDM/HTTPS/Telnet/SSH). I added a rule that allows SSH on the outside interface from 0.0.0.0 0.0.0.0. When I try to ssh in with putty, it says "server unexpectedly closed network connection" When I watch the logs on the ASA, it shows a Built inbound TCP connection on port 22, but then immediately a Teardown TCP connection. It doesn't show it's being blocked by any rule. Is there something I'm missing on enabling SSH?
View 13 Replies View RelatedI am not able to get to the internet from my DMZ ip address.
Here is my config.
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2(code)
I have a web server behind my 5505 that I'd like to access from the outside of the 5505 (still within my home network though). Its running on port 3000. I made the changes but I have been unable to access my server from the outside.
I do have an Airport Extreme in from of the 5505 and the 5505 is getting its address via dhcp from the airport. So I'm trying to hit 192.168.2.57:3000 from my wireless airport network.
[code]...
if log on to the firewall with the enable_15 account remotely via a Cisco IPSec VPN client? Similarly, how do you restrict access to the ADSM to the local LAN for the enable_15 account? Is there a way to tell when a user last logged on via an IPSec VPN?
View 4 Replies View RelatedIn Cisco ASA 5510 , outlook port only permit ( pop3 995/smtp :587) with TLS encryption. How we can do it thru ASDM .
View 1 Replies View RelatedI have question about license for ASA 5505. I have to put public access point behind ASA into DMZ. Do I need to hava the unlimited license? Does Securipty Plus license include unlimited users option and 50 VLAN or I will need different type of license.
View 2 Replies View RelatedWe have a Cisco ASA 5505. As of yesterday we could no longer access our web server (the web server is hosted off-site). Pinging the DNS address and direct IP (from the firewall and a PC) both return no response. Pinging the IP from the T1 router responds properly, meaning the router can access the web server, but the firewall cannot. Accessing the web server has never been a problem, and no configuration changes have been made to the network/firewall. Other locations can access the web server just fine.
View 1 Replies View Related