I have question about license for ASA 5505. I have to put public access point behind ASA into DMZ. Do I need to hava the unlimited license? Does Securipty Plus license include unlimited users option and 50 VLAN or I will need different type of license.
View 2 RepliesI have a branch office set up with a cable modem and an ASA 5505 as an easyvpn hardware client with network extension mode enabled, and connects to a PIX515E at the headend.I'm working on a separate issue for why the Internet connection drops periodically at the site, but my main problem is as follows.In this location, I have an 1142 LAP. It can boot up, and join the WLC just fine. Performance seems a little slow when it's working, but it works. The real issue is, if the VPN connection drops and reestablishes for any reason, the wireless clients all cease being able to communicate. All wired clients seem to bounce back without a problem.
The access point still shows to be joined to the controller, the access point never goes down, just wireless clients can't access anything any more. If I reload the access point, clients reassociate and continue on their merry way. For now, I am experimenting to keep the connection from dropping, but I'd really like to get it where I don't have to babysit this thing all day and night, and it can rejoin and function normally by itself after an outage.We are changing to this configuration from wireless bridging due to interference and reliability issues - however, I never experienced any similar issues with this particular access point before, so it's not the access point itself.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I can't access our ASA 5505 via SSH from the outside. I've configured this through the ASDM to allow SSH (Device Management > Management Access > ASDM/HTTPS/Telnet/SSH). I added a rule that allows SSH on the outside interface from 0.0.0.0 0.0.0.0. When I try to ssh in with putty, it says "server unexpectedly closed network connection" When I watch the logs on the ASA, it shows a Built inbound TCP connection on port 22, but then immediately a Teardown TCP connection. It doesn't show it's being blocked by any rule. Is there something I'm missing on enabling SSH?
View 13 Replies View RelatedI am not able to get to the internet from my DMZ ip address.
Here is my config.
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2(code)
I have a web server behind my 5505 that I'd like to access from the outside of the 5505 (still within my home network though). Its running on port 3000. I made the changes but I have been unable to access my server from the outside.
I do have an Airport Extreme in from of the 5505 and the 5505 is getting its address via dhcp from the airport. So I'm trying to hit 192.168.2.57:3000 from my wireless airport network.
[code]...
if log on to the firewall with the enable_15 account remotely via a Cisco IPSec VPN client? Similarly, how do you restrict access to the ADSM to the local LAN for the enable_15 account? Is there a way to tell when a user last logged on via an IPSec VPN?
View 4 Replies View RelatedWe have a Cisco ASA 5505. As of yesterday we could no longer access our web server (the web server is hosted off-site). Pinging the DNS address and direct IP (from the firewall and a PC) both return no response. Pinging the IP from the T1 router responds properly, meaning the router can access the web server, but the firewall cannot. Accessing the web server has never been a problem, and no configuration changes have been made to the network/firewall. Other locations can access the web server just fine.
View 1 Replies View RelatedNo connection via IE of any flavour
Chrome shows Error 113 (net::ERR_SSL_VERSION_OR_CIPHER_MISMATCH): Unknown error
I have 30 machines here, none of which have a serial port.
ASA Version 9.1(1)
!
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
[Code]....
I need to move the email traffic to a backup circuit. Below is my config. I have tried for email access but to no avail.
asa5505# sho run
: Saved
:
ASA Version 8.2(2)
!
hostname asa5505
[code]........
Cisco ASA 5505
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
I have and vpn tunnel between a pix network (192.168.200.0/24) and an asa network (192.168.100.0/24); it's been running fine for awhile now but this morning i've come in an i can not access anything on the pix network, (mail, file & web servers). Each attempt to access results in a SYN timeout.
6 Nov 30 2012 14:24:01 302014 192.168.200.9 192.168.100.115 Teardown TCP connection 6014 for outside:192.168.200.9/135 to inside:192.168.100.115/51240 duration 0:00:30 bytes 0 SYN Timeout
I'm currently facing a problem with a ASA5505. I've set it up from factory defaults... From the CLI, I can ping an the outside interface, the GW and an outside IP (ex:8.8.8.8).So I believe that there's no connectivity issue and the configuration is correct.
However, for a reason that I don't know, users can't have access to web pages.The product license allow me to have 50 host connected. Currently I've only got one host connected...
When I enable syslog, I can see the following messages :Deny traffic for protocol 17 src inside: 192.168.1.20/64429 dot ouside:8.8.4.4/53, licensed host limit of 0 exceeded.Where this limitation can come from ?
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedI am trying to enable access to use RealVNC on our Cisco ASA 5505 without using VPN. RealVNC uses port 5900. Users should be able to vnc to 99.23.119.78 and reach our internal server 192.168.1.4. So far they are receiving connection refused.
View 5 Replies View RelatedI have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
Relevant config of the remote ASA:
interface Vlan1
nameif inside
security-level 100
[Code].....
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.
I have config ASA 5505 and it is conencted to layer 3 switch that connects to cable Modem.
ASA is config with DHCP option and PC is able to get the IP from ASA. But from PC i am unable to access the internet. From ASA itself i am able to ping the Websites fine.
ASA has config with DHCP for inside and also it is doing NAT.
When i connect the ASA directly to Cable modem then pc is able to access the internet.
I've have an ASA 5505 with a inside network vlan1 (192.168.0.0/24) - i've configured an IPsec VPN profile and a VPN network of 192.168.0.50/24. I can through my VPN tunnel access inside hosts on vlan1 - but not ASDM on the ASA (192.168.0.1). Under management i've added the VPN network of 192.168.50.0/24 to have access to ASDM, but still does not work.
View 1 Replies View RelatedI would like to restrict Internet traffic (HTTP & HTTPS) for Inside Users with an ASA 5505. I would like to setup a proxy-like system where a User/Password must be entered before the User can actually browse the web.
I know that this can be done with an additional RADIUS/TACACS+ Server. Is this also possible without any external AAA Server, so with User/PW stored on the ASA locally only?
I am running into a issue that I cannot seem to figure out. I have a asa 5505 with the Security Plus license. I setup a native vlan where all of my network devices sit on. ie my Wireless Access point has an ip of 192.168.3.2, my switch .3. I have no issues managing these devices from any vlan I am on (permitting firewall access rules). When I try to access my ASA via ASDM/SSH. I have to use the gateway of the vlan I am on. For instance. If I am on vlan 10 I have to use 192.168.10.1 for access, if I am on vlan 20 I type 20.1...etc...etc If I type in 192.168.3.1 I get an error in the ASDM logs that states TCP reset by appliance. This is for any gateway I type except for the gateway of the vlan that I am connected to. I am posting a sanitized config. How can I configure the ASA to permit access via any gateway.
View 3 Replies View Related