Cisco VPN :: Wireless Access Point Behind ASA 5505 EasyVPN
Jan 23, 2013
I have a branch office set up with a cable modem and an ASA 5505 as an easyvpn hardware client with network extension mode enabled, and connects to a PIX515E at the headend.I'm working on a separate issue for why the Internet connection drops periodically at the site, but my main problem is as follows.In this location, I have an 1142 LAP. It can boot up, and join the WLC just fine. Performance seems a little slow when it's working, but it works. The real issue is, if the VPN connection drops and reestablishes for any reason, the wireless clients all cease being able to communicate. All wired clients seem to bounce back without a problem.
The access point still shows to be joined to the controller, the access point never goes down, just wireless clients can't access anything any more. If I reload the access point, clients reassociate and continue on their merry way. For now, I am experimenting to keep the connection from dropping, but I'd really like to get it where I don't have to babysit this thing all day and night, and it can rejoin and function normally by itself after an outage.We are changing to this configuration from wireless bridging due to interference and reliability issues - however, I never experienced any similar issues with this particular access point before, so it's not the access point itself.
View 4 Replies
ADVERTISEMENT
Feb 23, 2011
We have many new and very small remote sites that will be connecting via an ASA5505 using easy VPN. Works without an issue and we've got the configuration and process nailed down.
The challenge I was presented with today involve non-standard remote sites where I need to configure a third interface on an ASA 5505 and allow it to pass directly to the Internet and not go through the VPN. Configuration of the third interface, assignment and configuration of the ACLs / NAT(PAT) are straight forward.
The challenge I face and haven't been able to find a direct answer to is if it's possible to have the traffic bypass the easy vpn network extension process. At this time the traffic is going down the tunnel which isn't what I want.
I fear I'll have to build classic site-to-site VPN configurations which isn't a huge issue though it breaks all maintenance/operations methods, processes and I'll have to spend time training the support team how to detect the differences.
View 2 Replies
View Related
Oct 18, 2012
I've two sites, the branch with an ASA 5505 and on the corporate office i've an ASA 5510.I need to make a easy vpn tunnel between this to sites and I've made some configuration, but for now, the ikev1 isn't working.
View 1 Replies
View Related
Jul 11, 2011
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.
The Cisco ASA has the 50 internal user license with 10 VPN peers.
We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails.
Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences?
This seems to be the issue from what I can see, just need confirmation.
View 1 Replies
View Related
Mar 8, 2012
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.The Cisco ASA has the 50 internal user license with 10 VPN peers.We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails. Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences? This seems to be the issue from what I can see, just need confirmation.
View 3 Replies
View Related
Oct 10, 2012
I am installing 2 ASA 5505s at home offices with dynamic IPs. The EasyVPN server is a ASA585x. I am using the 5505s in NEM mode. I configured a unique DHCP scope on each 5505. I have a dynamic crpto map on the server. I configured unique tunnel groups, group policies and usernames for each site on the server. This seems to work fine. Is it normal to configure unique tunnel groups, group policies and usernames for each remote site?
View 2 Replies
View Related
Mar 2, 2011
When ASA 5505 was installed we selected Easy VPN Remote. Now we want to disable it. In ASDM we navigate to Configuration > Remote Access VPN > Easy VPN Remote and try to clear the Enable Easy VPN Remote checkbox but it will not uncheck.
View 2 Replies
View Related
Apr 28, 2011
So I have three ASA 5505 firewall. my firewalls we are in the test environment. I read on the net that when you have a situation like in my company where are headquarter and two offices, i should put in each branch office and headquarter one asa firewall and a firewalls should be configured as easyvpn.
VPN server is in headquarter and easyvpn's are in branch offices. i tried everything, but we could not configure them. maybe it's not a problem that in my test environment at my the external interfaces which have static addresses on these three firewalls, respectively serever 192.168.2.1, 192.168.2.2 and 192.168.2.3 client client. I seted firewalls by following the instructions, but does not work
[URL]...
I solved the problem with the server as a remote access VPN. client workstations that are on the 192.168.2.0/24 network can access a local LAN via VPN. But when you put the ASA 5505 firewall. clients on the LAN side of the firewall can not access the VPN. I use software products Cisco VPN Client 5.0.06, but when I create a connection and try to connect to get an error secure vpn connection terminated locally by the client. reason 412: the remote peer is no longer responding.
View 2 Replies
View Related
Jan 19, 2012
We have a number of 5505 ASAs at remote sites all of which are configured to connect to one of two head-end servers.We need to change the primary head-end IP addresses. At the moment devices are successfully connected to the secondary.If we issue vpnclient server i.j.k.l e.f.g.h then the device drops off the network and won't reconnect until it is power cycled.If we make the changes in ASDM using the GUI to remove the old primary and add in the new primary the ASDM says "No changes made".Devices are running 8.2 and 8.4 code and behaviour is the same.
how to change head-end server IP addresses without the device disconnecting and not coming back up? According to the configuration guide the ASA should cycle through the addresses every 8 seconds until it can connect - but it doesn't seem to do this as it won't connect to the good secondary head-end either!
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Jan 11, 2013
I have question about license for ASA 5505. I have to put public access point behind ASA into DMZ. Do I need to hava the unlimited license? Does Securipty Plus license include unlimited users option and 50 VLAN or I will need different type of license.
View 2 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Mar 20, 2012
i have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
View 5 Replies
View Related
Oct 26, 2010
I am using Cisco configuration professional to set up one easy vpn server on 887-K9,vpn client can dial up the server successfully but can only ping router but on other lan. Looks like there is a nat issues between lan and vpn client?
View 5 Replies
View Related
Aug 11, 2011
I using cisco 837 for incoming remote access VPN connections with are working very well but I recently created one outgoing easy vpn connection and I have issue since that time. As soon as easy VPN is up and established successfully I lost remote VPN access to internal subnet.
Where is :
Internal subnet: 192.168.172.0/24
remote VPN pool 192.168.24.2-6
Take a look at config attached and point me at missconfiguration
View 4 Replies
View Related
Jun 3, 2012
We have an ASA 5505 in our environment and currently two IPSec L2L VPN tunnels are established. But we are planning to connect using Easy VPN(Network Extension Mode) to another site as Client. Is it possible to configure Easy VPN configurations by keeping the currently active IPSec L2L VPN(Site-to-Site) tunnels?
Following is the warning that we get when tried to configure Easy VPN Client.NOCMEFW1(config)# vpnclient enable
* Remove "nat (inside) 0 S2S-VPN"
* Detach crypto map attached to interface outside
* Remove user-defined tunnel-groups
* Remove manually configured ISA policies
CONFIG CONFLICT: Configuration that would prevent successful Cisco EasyVPN Remote operation has been detected, and is listed above. P
View 6 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Jun 4, 2013
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
View 11 Replies
View Related
Dec 23, 2012
have netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies
View Related
Feb 8, 2013
having the same issue at work with an EnGenius EAP350 wireless access point. can't even get into the access point configuration login page. i've tried to connect both via ethernet cable direct and wirelessly, at the default ip address of 192.168.1.1, what else can i do to get into the configuration?
View 1 Replies
View Related
