Cisco VPN :: 5505 - Configure ASA Server And EasyVPN Client?
Apr 28, 2011
So I have three ASA 5505 firewall. my firewalls we are in the test environment. I read on the net that when you have a situation like in my company where are headquarter and two offices, i should put in each branch office and headquarter one asa firewall and a firewalls should be configured as easyvpn.
VPN server is in headquarter and easyvpn's are in branch offices. i tried everything, but we could not configure them. maybe it's not a problem that in my test environment at my the external interfaces which have static addresses on these three firewalls, respectively serever 192.168.2.1, 192.168.2.2 and 192.168.2.3 client client. I seted firewalls by following the instructions, but does not work
[URL]...
I solved the problem with the server as a remote access VPN. client workstations that are on the 192.168.2.0/24 network can access a local LAN via VPN. But when you put the ASA 5505 firewall. clients on the LAN side of the firewall can not access the VPN. I use software products Cisco VPN Client 5.0.06, but when I create a connection and try to connect to get an error secure vpn connection terminated locally by the client. reason 412: the remote peer is no longer responding.
i have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.
The Cisco ASA has the 50 internal user license with 10 VPN peers.
We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails.
Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences?
This seems to be the issue from what I can see, just need confirmation.
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.The Cisco ASA has the 50 internal user license with 10 VPN peers.We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails. Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences? This seems to be the issue from what I can see, just need confirmation.
I need to configure our ASA5505 firewall for remote access to our network using EasyVPN software installed on a laptop. That laptop will be connected in the different places, using DSL or 3G toggle or Public Wi-Fi. For some people it's very easy, but I don't have any experience with firewalls.
I have couple of issues with my EasyVPN server and Cisco VPN Client on Win7.
1: VPN Client establishes the connection, traffic flow, destination network can be pinged. After a few minutes traffic stops passing the VPN. No ping to IP or DNS names can be made. In order to resole it. Users have to re-establish the VPN again. Occastioanl it stays and continue to work.
2: VPN Clients don't pick the same IP address from local address pool even though I specified "RECYLE" option in the IP local pool command.
Configuration:
############################################################################## TQI-WN-RT2911#sh run Building configuration... Current configuration : 7420 bytes ! ! Last configuration change at 14:49:13 UTC Fri Oct 12 2012 by admin ! NVRAM config last updated at 14:49:14 UTC Fri Oct 12 2012 by admin
I have been trying to configure Cisco1941/K9 as Easy VPN Server through CiscoCP.The tunnel comes up but I cannot pass any traffic to the secure LAN (GigEth 0/1). When the tunnel comes up, I can ping the Loopback interface and the GigEth 0/1 interface IPs.
I have a Cisco ASA 5510 and a Cisco ASA 5505. I want to configure the ASA 5510 as Easy VPN Server and 5505 as Easy VPN hardware client.Using either CLI or ASDM.
We have a number of 5505 ASAs at remote sites all of which are configured to connect to one of two head-end servers.We need to change the primary head-end IP addresses. At the moment devices are successfully connected to the secondary.If we issue vpnclient server i.j.k.l e.f.g.h then the device drops off the network and won't reconnect until it is power cycled.If we make the changes in ASDM using the GUI to remove the old primary and add in the new primary the ASDM says "No changes made".Devices are running 8.2 and 8.4 code and behaviour is the same.
how to change head-end server IP addresses without the device disconnecting and not coming back up? According to the configuration guide the ASA should cycle through the addresses every 8 seconds until it can connect - but it doesn't seem to do this as it won't connect to the good secondary head-end either!
I'd like to configure a VPN with two SR520. the first router is a SR520-FE-K9 and it's at office, the second router is a SR520-ADSL-K9 and it's at home.
Each router have a static IP and individually works well. I tried to configure, by CCA, the office router as a server and the home router as a client: at home I can't see the office network and I can't navigate.
Need step by step, using CCA to configure a secure VPN.
How can I configure an ASA 5505 NEM client to allow access to the Internet when the tunnel to the headend is down? I am planning on deploying back to back ASA 5505s in network extension mode but I do not want to block Internet access on the client side if the tunnel to the server should go down.
(Router is ISR 1921)This is doing my head in. I am not using NAT, there are no ACLs, there is no split horizon.Here is what I have. It is practically generated by CCP. When connected I cannot ping the loopback interface or the gig0/0 interface, (not to mention anything else).
version 15.0 service config service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname dcsgw1
I am using Cisco configuration professional to set up one easy vpn server on 887-K9,vpn client can dial up the server successfully but can only ping router but on other lan. Looks like there is a nat issues between lan and vpn client?
We have many new and very small remote sites that will be connecting via an ASA5505 using easy VPN. Works without an issue and we've got the configuration and process nailed down.
The challenge I was presented with today involve non-standard remote sites where I need to configure a third interface on an ASA 5505 and allow it to pass directly to the Internet and not go through the VPN. Configuration of the third interface, assignment and configuration of the ACLs / NAT(PAT) are straight forward.
The challenge I face and haven't been able to find a direct answer to is if it's possible to have the traffic bypass the easy vpn network extension process. At this time the traffic is going down the tunnel which isn't what I want.
I fear I'll have to build classic site-to-site VPN configurations which isn't a huge issue though it breaks all maintenance/operations methods, processes and I'll have to spend time training the support team how to detect the differences.
I've two sites, the branch with an ASA 5505 and on the corporate office i've an ASA 5510.I need to make a easy vpn tunnel between this to sites and I've made some configuration, but for now, the ikev1 isn't working.
ASA 5505 running 8.2 with ASDM 6.2. VPN Client Version 5.0.05.0290
I've installed both the anyconnect and ipsec VPN clients and successfully connected for remote VPN server access; however, the client shows no packets being returned. Thinking that I misconfigured, I reset to the factory default and began again. Now I only have the ipsec vpn configured and I have exactly the same symptoms. I followed the directions for configuring the ipsec vpn in Document 68795 and rechecked my configuration and I don't see what I've done wrong. Given that I can connect to the internet from the inside network, and I can connect to the VPN from outside the network (and the ASDM Monitor shows an active connection with nothing sent to the client) I have to believe it is either a route or an access rule preventing communication but I can't quite figure out where (and I've tried static routes back to the ISP and a wide variety of access rules before flushing everything to start over).
I am configuring remote access vpn on ASA5505.Everything is working fine so far, except when the client got connected, it still used the local DNS server provided by the ISP. How do I force the client to use the DNS server configured on ASA?
I want to configure my Cisco asa 5505 as a dns server, so that when i configure any of my network systems ip address and use my firewall as a default gateway and dns ip, the system should be able to browse internet.
I have a branch office set up with a cable modem and an ASA 5505 as an easyvpn hardware client with network extension mode enabled, and connects to a PIX515E at the headend.I'm working on a separate issue for why the Internet connection drops periodically at the site, but my main problem is as follows.In this location, I have an 1142 LAP. It can boot up, and join the WLC just fine. Performance seems a little slow when it's working, but it works. The real issue is, if the VPN connection drops and reestablishes for any reason, the wireless clients all cease being able to communicate. All wired clients seem to bounce back without a problem.
The access point still shows to be joined to the controller, the access point never goes down, just wireless clients can't access anything any more. If I reload the access point, clients reassociate and continue on their merry way. For now, I am experimenting to keep the connection from dropping, but I'd really like to get it where I don't have to babysit this thing all day and night, and it can rejoin and function normally by itself after an outage.We are changing to this configuration from wireless bridging due to interference and reliability issues - however, I never experienced any similar issues with this particular access point before, so it's not the access point itself.
I am installing 2 ASA 5505s at home offices with dynamic IPs. The EasyVPN server is a ASA585x. I am using the 5505s in NEM mode. I configured a unique DHCP scope on each 5505. I have a dynamic crpto map on the server. I configured unique tunnel groups, group policies and usernames for each site on the server. This seems to work fine. Is it normal to configure unique tunnel groups, group policies and usernames for each remote site?
When ASA 5505 was installed we selected Easy VPN Remote. Now we want to disable it. In ASDM we navigate to Configuration > Remote Access VPN > Easy VPN Remote and try to clear the Enable Easy VPN Remote checkbox but it will not uncheck.
How to configure cisco 3560 to force the client only can get ip by dhcp-relay server ?
The company i am working in has 5 vlans which have been set an lay-3 switch(3560), uses the dhcp-relay server .(in svi configuration: ip helper-address X.X.X.X) well , that works ok~
Now , I got my problem: I need to force the client only can get ip by dhcp-relay server, that means if anyone set static IP manunally , he can't really access to anywhere (to provent anyone set static IP with malignancy )
I know if a h3c router , how to set this configuration n svi configuration : dhcp relay security address-check enable ) the how to configure on a cisco 3560 ?
I don't seem to be able to connect to my cisco 831 router with easy vpn server configured using my Blackberry Playbook. Looking at the console of the router i can see the debugging but am not sure what it all means.
Currently I have an ASA setup as a Firewall with 1 outside interface and 2 inside interfaces. Initially, the Guest interface was setup to receive DHCP from the ASA and everything was working. I'm adding router and a server for the guest interface and what I'm trying to accomplish now is the following: ASA 5505 > Airport Extreme with a public static IP (69.xx.xx.6), handling DHCP and NAT > Mac Server as DNS Server.Right now, when I connect to my Airport Extreme with any computer, I don't have internet. I don't understand what's wrong. My DNS Server has a reserved IP address: 192.168.226.2 and it's pointing to itself and forwarding the ISP DNS servers, the Airport Extreme is handling the DNS Server IP and the ISP DNS Server IP but I can't connect to the internet from the server. [code]
We've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
I am using 3945E Router as Easy VPN Server, with 15.1 IOS. On router I have bunch on usernames for VPN authentication, I want to restrict Router management access for them(ssh,telnet, http and so on).
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
We have an ASA 5505 in our environment and currently two IPSec L2L VPN tunnels are established. But we are planning to connect using Easy VPN(Network Extension Mode) to another site as Client. Is it possible to configure Easy VPN configurations by keeping the currently active IPSec L2L VPN(Site-to-Site) tunnels?
Following is the warning that we get when tried to configure Easy VPN Client.NOCMEFW1(config)# vpnclient enable
We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142) Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
