Cisco WAN :: SR520 - Configure VPN With (server And Client) Using CCA
Mar 15, 2012
I'd like to configure a VPN with two SR520. the first router is a SR520-FE-K9 and it's at office, the second router is a SR520-ADSL-K9 and it's at home.
Each router have a static IP and individually works well. I tried to configure, by CCA, the office router as a server and the home router as a client: at home I can't see the office network and I can't navigate.
Need step by step, using CCA to configure a secure VPN.
I´m trying to configure SR520 Cisco router as PPPoE server. The point is, when configuration is done and PPPoE client is directly connected to the interface, SR520 doesn´t respond to incoming PADI. PADI is not shown in PPPoE debugs (debug pppoe events, packets and errors).On the other hand, I get the PADI capturing packets with wireshark (so PADI is being sent) and the same configuration on other router works fine.
I am having a tough time getting my VPN client to reach any devices on my office network. I have a Cisco SR520 configured with IPSec to terminate Cisco VPN client sessions. The client is able to connect successfully. I get a username/password challenge, and then I get assigned a pool IP address on the client computer. So the VPN connection looks good at that point but I cannot reach any devices in the office network.
Config below:
Building configuration... Current configuration : 8066 bytes ! ! Last configuration change at 06:14:35 PDT Wed Apr 13 2011 by admin ! NVRAM config last updated at 06:17:11 PDT Wed Apr 13 2011 by admin ! version 12.4
So I have three ASA 5505 firewall. my firewalls we are in the test environment. I read on the net that when you have a situation like in my company where are headquarter and two offices, i should put in each branch office and headquarter one asa firewall and a firewalls should be configured as easyvpn.
VPN server is in headquarter and easyvpn's are in branch offices. i tried everything, but we could not configure them. maybe it's not a problem that in my test environment at my the external interfaces which have static addresses on these three firewalls, respectively serever 192.168.2.1, 192.168.2.2 and 192.168.2.3 client client. I seted firewalls by following the instructions, but does not work
[URL]...
I solved the problem with the server as a remote access VPN. client workstations that are on the 192.168.2.0/24 network can access a local LAN via VPN. But when you put the ASA 5505 firewall. clients on the LAN side of the firewall can not access the VPN. I use software products Cisco VPN Client 5.0.06, but when I create a connection and try to connect to get an error secure vpn connection terminated locally by the client. reason 412: the remote peer is no longer responding.
Im trying to configure a SR520 with the CCA, but every time I try and apply the changes to the router i get the following error.
"java.lang.nullPointerException"
Using CCA 3.0(1) and Java Version 1.6.0_16 from Sun Microsystems Inc?I assume this is an issue with Java, as like with the SDM you had to use an Old Vertion.
How to configure cisco 3560 to force the client only can get ip by dhcp-relay server ?
The company i am working in has 5 vlans which have been set an lay-3 switch(3560), uses the dhcp-relay server .(in svi configuration: ip helper-address X.X.X.X) well , that works ok~
Now , I got my problem: I need to force the client only can get ip by dhcp-relay server, that means if anyone set static IP manunally , he can't really access to anywhere (to provent anyone set static IP with malignancy )
I know if a h3c router , how to set this configuration n svi configuration : dhcp relay security address-check enable ) the how to configure on a cisco 3560 ?
My operations manager says "Could you go on-site and configure a new clients new internet connection?" I make the arrangements and go on-site. As I'm working with the providers tech he says "Do you have a sub-interface confgured for a dot1q VLAN id of 1057?", I say "What?". Anyway my firewall is not capable of dot1q VLAN, so he says "Do you have a Cisco router that can provide the trunking?", I say "Yes, I tink so but not with me". The question is can I use an SR520 between my firewall and the provider demarc to route the VLAN he is talking about? My initial discovery says yes but I am not quite sure of the details on how to achieve this on the SR520.
I'd like just notify the missing "no ip name-server" command in sr520 series router. However is possible to enter the command "ip name-server" the only way to delete it is to copy a modified config from tftp or other source to the startup config. This behavior is normal?
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
I did some searching and the answers said it was supposedly possible but no info on how to do it. I am wondering if it is possible to configure a Cisco ASA 5505/10/20 to be a client to an existing (in this case) cisco client vpn. The reasons why are complicated (and imo irrelevant) but basically I need to be able to make a small network that can be on this vpn rather than individual machines.The client vpn is a basic IPSec over UDP Cisco VPN to an ASA5505.So how would I configure another ASA to connect to this like its a client?
I have a small CCENT/CCNA lab with a few switches and routers which I would like to connect to my D-link home router so that it can access the outside world. I have an 877W which I believe is supposed to be able to connect to a wifi network as a client.
I have seen reference to configuring a bridge but this is something outside of my current understanding. The idea is to have the 877W with it's wireless interface connected to my wireless network and the Lab connected to the 877's intergrated switch, using the 877 as a basic router connecting the two networks. I've scoured Google and put together a configuration using what I could find in forum posts and Cisco documentation. The D-link is set up for auto WPA/WPA2 Personal (TKIP or AES). I'm using an ASCII key with an update interval of 0. I've never had a problem with other devices trying to connecting to it.
At the moment the 877W seems to connect to the D-link but then lose it's association, from what I can see it looks like the 877 is trying to rotate the key? Once this happens my laptop loses it's wireless connection and I need to reboot the D-link to get it back. Interestingly the Windows 7 network icon shows three computers with a link between each as the network icon when this happens. It's as if the 877W acts as a Rogue access point and steals my client's connection. On one attempt the debug output showed the 877 geting an IP address from the D-link's DHCP so it does seem to connect initially.
Is there a way to configure a disclaimer that will pop up on the client machine that they will need to accept to be allowed access to the wireless network?
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
I'm trying to configure my Linksys E2000 to be an ethernet attached wireless device to use on computers instead of dongles, etc. I don't want it to route, just act like a Wireless card.
I need to configure our ASA5505 firewall for remote access to our network using EasyVPN software installed on a laptop. That laptop will be connected in the different places, using DSL or 3G toggle or Public Wi-Fi. For some people it's very easy, but I don't have any experience with firewalls.
i am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...
Connect my linksys WRT54GL router to the proxpn vpn privacy service as a client? (or any other vpn privacy service for that matter) I already have an internet connection up and live with a cisco router so I would need to connect the linksys to the cisco and use the linksys as a vpn gateway kind of thing, so that any computer connected to the linksys will automatically be in the vpn tunnel without needing any cleint software installed on it. The vpn service I use is proxpn but they won't support the settings of individual routers (understandable). The only setting they give for a PPTP connection is here
How can I configure an ASA 5505 NEM client to allow access to the Internet when the tunnel to the headend is down? I am planning on deploying back to back ASA 5505s in network extension mode but I do not want to block Internet access on the client side if the tunnel to the server should go down.
I know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
I insert data from two clients.(1 window server 2003,2 XP clients ) the two client print paper and the printer is shared printer. At the same time two clients print paper and the printer stop working. So I restart my two clients and server. After restart the clients cannot ping to server.
Can I have two asa firewall between dhcp client and dhcp server. if yes what solution i have to have to get dhcp leases. should i have to configure dhcp relay on both the asa.
I am trying to connect some thin clients to a domain based windows 2003 server. This the first time mi trying to do this. If the computer is set to workgroup there is no problem. The problem comes up when its a domain based server.I keep getting the message that the user is logged in. The host computer connecting to the server has the user name "thinclient" and I use the name "user" to log in from the thin client. But it says "thinclient" already in use and disconnect my connection between the host and the server.
I am installing Window Server 2008 with file Services, and I am making my clients to save files to their documents folder but those files are being saved straight in the Server. I was wondering if It is better to save files direct to the server or save files in each client?
