Cisco Firewall :: ASA 5505 / Lost Enable Password For Spare Device?
Jul 13, 2011Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies
ADVERTISEMENT
Cisco Firewall :: On ASA 5520 Device Enable Password Is Not Getting Changed
May 23, 2011I try to change password on the ASA 5520 device and its not getting changed.
FW(config)# enable password cisco1234(config)# end
After that I perform a write memory.
But somehow I relogin again the enable password still remain as the old enable password
version : 7.2(5)2.
Cisco Switching/Routing :: 3750 Switch - Lost Enable Password
May 2, 2013I have lost the "ENABLE" password on my 3750 switch.
View 5 Replies View RelatedCisco VPN :: Resetting Enable Password On ASA5505 Device
Jul 9, 2012resetting the disable password on an ASA5505 device
View 9 Replies View RelatedCisco Firewall :: ASA5510 Enable Password Not Working
Oct 11, 2012I have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies View RelatedCisco Firewall :: How To Enable SSH With ASA 5505 Running 8.3(2)
Aug 2, 2011I'm replacing a new ASA 5505 due to a corrupted flash. On the original unit, I had the ability to SSH into the device using TeraTerm with no problems. While configuring the new device, I entered commands to enable SSH into the unit.
View 5 Replies View RelatedCisco Firewall :: Enable SIP From Outside To Inside (ASA 5505)
May 14, 2012We recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)
[Code].....
Cisco Firewall :: ASA 5505 Lost Internet Connection?
Feb 27, 2011I changed a configuration and suddenly I lost the internet connectivity... Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif ATT security-level 0 pppoe client vpdn group ATT ip address pppoe setroute !interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone EST -5clock summer-time EDT recurringsame-security-traffic permit inter-interfaceobject-group service DM_INLINE_TCP_1 tcp port-object eq ftp port-object eq ftp-data port-object eq wwwaccess-list ATT_access_in remark Linkstation Accessaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in remark Linkstation
[code]....
Cisco Firewall :: ASA 5505 During Set Up Lost Contact With Unit
Feb 4, 2012Did setup iaw instructions. got to step 9 where it went into configure mode. last few messages
192.168.1.5 to 192.168.1.1 (BUILT IN BOUND TO TO IDENTIFY), then
192.168.1.5 START SSL HANDSHAKE FOR TLSW1 SESSIN, THEN
192.168.1.5 COMPLETED HANDSHAKE, THEN
[Code].....
now i am unable to do anything with the 5505. can not log in , can not get a ping of 192.168.1.1, can not get into the unit and do a factory reset
Cisco Firewall :: To Enable Access To Use RealVNC On ASA 5505
Feb 27, 2011I am trying to enable access to use RealVNC on our Cisco ASA 5505 without using VPN. RealVNC uses port 5900. Users should be able to vnc to 99.23.119.78 and reach our internal server 192.168.1.4. So far they are receiving connection refused.
View 5 Replies View RelatedCisco Firewall :: How To Enable DHCPD Logging In ASA 5505
Aug 11, 2011I have configured dhcpd in an ASA 5505 and every thing is working. I am testing it to give me a warning when the address pool is about to be finished or it is empty. But don't konw how to do it. if I run the "debug dhcpd packet", i get that the address pool is empty.
View 3 Replies View RelatedCisco Firewall :: To Enable Anti Spoofing ASA 5505
Apr 24, 2011What is Anti Spoofing in ASA 5505. Can I enable it on ASA 5505. If yes , port will be inside or Outside. ? or both ?
View 1 Replies View RelatedCisco Firewall :: DHCP Server Won't Enable - ASA 5505
Nov 1, 2012I get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
Cisco Firewall :: ASA 5505 Enable Live Traffic?
Mar 14, 2012I am currently troubleshooting a firewall policy on a ASA 5505. What command can enter in the CLI to enable live view of traffic been block and which traffic is been allow?In my experiences with other firewall vendors, other firewalls allow me to narrow down the source and destination, too. is there such thing on the ASA 5505?
View 6 Replies View RelatedCisco Firewall :: 5570 - How To Change Telnet And Enable VPN User Password
Jun 17, 2011how do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies View RelatedCisco Firewall :: Enable Netflow On ASA 5505 For Vlan And Interfaces
May 17, 2013How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
Cisco Firewall :: ASA 5505 - Enable Top Usage Tab On ASDM Dashboard?
Feb 3, 2011Today I upgraded my Cisco ASA 5505 ASDM from version 6.34 to 6.41 cause of some problems on old version with NetFlow. But now when I switch to dashboard i can not see "Top Usage" tab. That was quite usefull for me. It simply disappeared.
Can i somehow configure which tabs are displayed on dashboard ? I really need that one and I do not want to downgrade :/
Cisco Firewall :: ASA 5505 Making A Device Inaccessible Via Vpn
Apr 21, 2013Within a workgroup environment we have four large drives, statically assigned and all accessbile via VPN. Our FW is a Cisco ASA-5505. Where within the ASA-5505 GUI can one of these drives be made inaccessible via VPN ?
View 0 Replies View RelatedCisco Firewall :: Planning To Integrate ASA 5505 Device
Mar 21, 2011I planning to integrate cisco asa5505 device in runing enviornment for filter ip traffic.Internet ----router----ciscoasa----lan.Ip series is public(25.263.25.0/24) througout of network (no privateIP)now how do I set asa in such case and filter traffic from comming into lan and going out to internet.
View 5 Replies View RelatedCisco Firewall :: 5510 - Multiple ASA Configs For Cold Spare
Oct 2, 2012I have a few sites all running Cisco ASA 5510s. They all share the same asa (8.4(4)1) and asdm (6.4.9) version, but their configs differ significantly. I have a cold spare sitting in my office in the event we have a physical failure. Is there a quick and simple way I can load up multiple configs and then boot up the cold spare to then run the config from Site_A or Site_B? Just looking for a quick solution rather than doing a full restore should something fail spectacularly. Nice to say upon bootup, using confreg perhaps, to boot Site_A config rather than Site_C.
View 1 Replies View RelatedCisco Firewall :: ASA 5505 Portforwarding To Device With Different Default Gateway
Feb 27, 2012A customer got a new VoIP PBX, and now I have to forward port 443 on the ASA to the PBX for remote administration purposes. The LAN-interface of the PBX is in the same subnet as the ASA but has an external VoIP-router as default gateway and not our ASA. Is it even possible to forward the port to the PBX when there is no route of any sort to our ASA on it?
View 2 Replies View RelatedCisco Firewall :: ASA 5505 - Losing Configuration When Device Powered Off
Feb 28, 2011i did a reset on my asa by stopping the boot process because i could not remember what my enable password was, i had no problems with the reset the asa came backup as it should and i started configuring the device again. My problem is when the device is powered off and back on i lose all configuration that were made, i save the changes with "write me" before the restart and they are still being over wrote.
View 4 Replies View RelatedCisco Firewall :: ASA 5505 Connection Limit And TIME_WAIT Freezing Device
Sep 30, 2011My little ASA 5505 is working great The device appears to be artificially crippled and limited to 10,000 connections. This isn't a "CPU limit" it's just some fake limit in the device as far as I can tell.
The problem we have is that we are only using around 500-600 connections and CPU usage is only like 25%, and yet the connection count is pegged at 10,000 and locks us out of our network.
I am pretty sure this is because there are a lot of "dead" TIME_WAIT connections hanging around not being used. In our application we only have the couple hundred connections but they do move around a bit every now and then.
Is there anyway to get the device to ignore the "dead" connections and not count them towards the artificial limit on the device given that it's pretty clear the CPU / etc., is not utilized sufficiently. These aren't real connections, we only have a couple 100 established, they do just move around a bit however.
We are really only using 500-700 connections according to our servers, the others are just sitting in TIME_WAIT doing nothing.
Cisco Firewall :: Asterisk / FreePBX Phone System Located Behind ASA 5505 Device
Feb 27, 2011We have an Asterisk/FreePBX phone system located behind an ASA 5505 device where we are having problems with sip inspection.
We connect to three different phone providers, and things works as expected for 2 of the 3 providers,but for the last one (Draytel) we are having problems with sip inspection.
The key difference about the VoIP provider where we are having problems is that they are using differetn servers for the voice (RTP) traffic than the server we are registered with to establish SIP sessions.
sip inspection is configured with the default out of the box options.The problems we see are this:
1. For ingoing calls sip inspection does not open the required pinhole to allow the traffic to flow through. As a result we can not hear the voice of the calling party, but voice from our side is passed through ok.As a workaround we have added and ACE allowing traffic in the used UDP (RTP) range from this VoIP providers ip addresses to pass through the ASA, and with that in place incoming calls work.
2. Outgoing calls doesn't work because sip inspection doesn't kick in, and as a result of this we forward internal ip addresses in the SIP / SDP body to the VoIP provider. I'm not sure whether this is a consequence of sip inspection not kicking in for this provider, or a result of having added the ACE for an ip ragnge that covers the ip address we register with.
As stated above sip inspection does work as expected for two other providers where all traffic goes through a single server.We actually have had this working with ASA firmware 7.2(4), but as that version intermittently had a problem where sip inspection would stop working (fixable by power off/on or a clear command), then we decided to upgrade.
Cisco Firewall :: Can Remember Password To Login To ASA 5505
May 27, 2011I got an ASA 5505 recently and i'm new to using firewalls but have forgotten the username and password that was set on it for login using SSH (putty). Is there a way i can stiil login to it or even reset the password so i can login using Putty?
View 1 Replies View RelatedCisco Firewall :: Configure ASA 5505 With Username And Password
Nov 1, 2012I am trying to configure an ASA 5505 with a username and password. I set all the pass words: [code]
When I reload the device it prompts me for the username, then the password and it fails and just asks for the username again. I have even tried to delete the username / password combo but it still prompts me for it. When I do password recovery the confreg is 0x00000001.
Cisco Firewall :: ASA 5505 - Download Configuration Before Resetting Password?
Mar 24, 2013I am new with ASA devices I have a ASA 5505, the former IT manager does not remember the password of it. I am just wondering do I lose the configuration on it if I reset the password?if yes, how can I download the configuration before resetting the password. and how can I upload the downloaded configuration
View 2 Replies View RelatedCisco Firewall :: ASA 5505 - ASDM Logon / Reset Username And Password
Sep 6, 2012I completed the PIX 515 to ASA 5505 migration today with no problems - ok one problem with the logon for ASDM. I'm trying no username and password - then using username and password from the 515 Pix with no success. How to reset the username and password for the ASDM GUI website.
View 3 Replies View RelatedCisco Wireless :: WAP4410N-G5 - All Settings Lost After Enable / Disable
Oct 3, 2011I received WAP4410N-G5 AP with 2.0.2.1 firmware and set up it very easily. Never experienced a single signal drop in a few days.
After updating firmware to 2.0.4.2 version I am completly unable to make any changes! If I press on "Enable" or "Disable" all settings will be lost after I apply them and neither "Enabled" nor "Disabled" is selected.
Had to revert back to 2.0.2.1. Is my AP faulty?
Cisco Firewall :: ASA5555-X - Spare Ports Into Access Ports?
May 14, 2013Is there a way to associate spare firewall ports with another port that is being used..For example...int gi 0/2 is being used currently for my web dmz. Its ip is 192.168.10.1..Is there a way for me to associate gi 0/3 with the same layer 2 as gi 0/2 ?
In my webdmz I use 2 ACE 4710 proxys in FT mode. I used a layer 2 switch to connect firewall and proxys together.
I would like to eliminate this switch if possible..and connect both 4710's (layer 2) direct to firewall.If I could make gi0/2 - 4 part of the same vlan, then I would be good to go.
How To Enable WLAN In Device Manager
Feb 10, 2011In my laptop WLAN is showing disabled from Device Manager & no Wireless is showing in the Network Adaptar under Device manager.
View 5 Replies View RelatedLost Password For Net Name?
Sep 28, 2012had to install new router(d link) on PC and since then cant get wi fi on my laptop or i pad. keeps asking for password for net name , which i have forgotten.
View 1 Replies View RelatedCisco WAN :: 877 - No Password Recovery / IOS Lost
Oct 2, 2011I have a couple of 877s which have "no service password recovery" set and something has happened to the flash or the IOS has been lost for one reason or another.
When trying to boot the routers, they all display similar to this, which then repeats:
[code]....
Or words to the effect of there being no IOS at all, unable to boot, but the result is the same, it just loops and there's nothing I can do to break the sequence!
I've tried taking the flash from a working 877 and replacing the card but this doesn't work and unfortunately, putting the once working strataflash card back in the working 877, it gets the same problem!