I try to change password on the ASA 5520 device and its not getting changed.
FW(config)# enable password cisco1234(config)# end
After that I perform a write memory.
But somehow I relogin again the enable password still remain as the old enable password
version : 7.2(5)2.
Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies View RelatedToday I wanted to change my passwords on my router Cisco 888e.I connect by telnet my router and access the enable mode.Then, I set my enable password to passwordxxx with the command enable password password1.After a show run, i could see in this config my new password correctly set. Then, I set my enable secret password to passwordxxx (the same) with the command enable secret password password1.I log off the enable mode.Try to log on with the command en but when I type the new or the old password, I receive a 'Access denied' message.
And I'm sure of the new one because on my command line to define it I could see this new password in clear!What are my solutions to access the enable mode again?If I reboot my router, it'll run the previous config file with the old password? I've only worked on the running config file and haven't apply these changes to the nvram.
Changed my AD password and now i cannot get into the enable side of the cisco switches on our network (we have no routers).Looking on the logs for the ACS v4.2 I can see the following -
On TACACS+ Accounting you can see the connections which have worked - it the initial tty connections -
When i look in the failed attempts i see the following Auth failed - External DB user invalid or bad password or on another occasion internal error or EAP-TLS or PEAP authentication failed due to unknown CAcertificate during SSL handshake.
resetting the disable password on an ASA5505 device
View 9 Replies View RelatedHave cisco ASA5520 on place and i want to configure it to access my webserver outside of my network throught sftp/ftp with filezila what command to add so as port/service associate to it should be able to run?
View 1 Replies View RelatedI have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies View Relatedhow do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies View Relatedwe have two ASA5520-AIP40-K8 in our office and we purchase IPS service for one only, can we also update the signature of second device before purchasing additional IPS Services for second unit
View 1 Replies View RelatedIn my organization we have 2 sites. These 2 sites have ASA 5520s, and the l2l between each ASA. The interface that is forming the VPN tunnel is on the ASA, NATed on the router. These ASAs sit behind the router, which are then connected to the ISPs. Recently, we had to change the ISP that we were creating the tunnel on, from Comcast to Sprint on our remote site. I re NATed the interface, and the l2l tunnel came back up after editing the tunnel-group, crypto maps, and reapplying the crypto map to the interface. However, our remote access VPN no longer works on the ASA that we changed the IP on. The other side was never changed, and still works fine. When I tried using debug cry isa and debug cry ip sec on the firewall, nothing shows when we attempt to connect. We are using IPsec over TCP. On the ASDM log, it says: Deny TCP (no connection) from xx.xx.xx.xx/49907 to xx.xx.xx.xx/10000 flags RST on interface WAN.
The VPN worked fine before, could it be an ACL thing? All we changed was the IP so that's what I'm inclined to believe, but on the router none of the interfaces have an ACL that's applied to them. It can't be on the ASA, because I believe we have the option to ignore the ACL enabled, but I might be incorrect about this. I'm new at ASA/VPNs in general.
I would upload the configs, but is there a pertinent output that would work, or just a general sh run?
i have a active/standby pair of asa 5520's, i can access the active asa but not the standby asa via console,
i have tried the password recovery on the standby unit but it does not work, do i need to remove the unit from the network to become a standalone unit to perform the recovery?
The customer forgot the password for the ASA SSM-20 ips module installed in ASA 5520 Fw.show module in customer FW shows it up state. I brought it to our office teat bed. here it show
ASA1# sh module
Mod Card Type Model Serial No.
--- -------------------------------------------- ------------------ -----------
0 ASA 5520 Adaptive Security Appliance ASA5520-K8 JMX1022K03A
1 ASA 5500 Series Security Services Module-20 ASA-SSM-20 JAB101003C2
Mod MAC Address Range Hw Version Fw Version Sw Version
[code]....*-
what to do with this module in my test bed.I have to take it back to the customer site to use it in their ASA itself to troubleshoot.There it the status is up and i did use all the hw-module option but no use. The version is 5.0. This module is more than 5 years old and so far no one upgrade the image. ASA 5520 running 8.2.5.
i tried using the internet on my ipod but my wifii network wasnt connected so i went to my wifi settings on my ipod and the network name and password were changed. i tried resetting my router but nothing happened and i still cant get wifi on my ipod.
View 1 Replies View RelatedMy mother accidentally turned off wireless or changed the password to the 2WIRE778 that we have and I can't get wifi on my iPod. So I have a small motorola router and it's wireless so if I hook it up to the original 2WIRE that has blocked wifi do you think I can get wifi off the second router with no password troubles or would I have to buy a special router that has no password? I don't know a lot about computers. And my Meyer has a password on our computer so I can't log on. so if I just hook up the 2nd router and possibly get WiFi do I need to do anything such as setup on the computer or can I plug it in and just go?
View 1 Replies View RelatedI have DIR600 Rev. B1 for about 2 years, and it's been working without a problem.Suddenly yesterday, I could not connect to the internet from my 2 laptop & blackberry.SSID & signal reception looks normal. On checking into the router's web interface, I noticed that the network key was changed into something else.....normal character like y2tz39s.
I'm being very curious. Has it been hacked ? Is it possible?I'm using WAP/WAP2 Security Setting for wireless connection.All other settings seems intact (firewall & even the SSID). Only the password was mysteriously changed. If I consider it being hacked, I wonder why the hacker didn't mess up all other settings ?
My son decided to update our router firmware, together with this the password was changed. My computer which hosts the Internet connection works fine, all other laptops have now been connected successfully after simply changing the password. However my wifes laptop won't play ball. It is a Samsung R510, with Vista Home Premium OS. It worked fine prior to updating the firmware. I have been through the process of changing the password and have the correct security encryption in place, exactly the same process as with the other laptops.
It then says successfully connected, but shows in the bottom right of the screen, Unidentified network access local only and will not connect when the browser is opened. I have tried to diagnose but the usual windows prompt to reboot both modem and router has no effect. I have set it to private, as advised elsewhere, I have switched the firewall off and removed security software, all to no avail.
I tried the command prompt, then ipconfig/renew. An error occurred while renewing interface Wireless Connection: unable to contact your DHCP server. Request has timed out. No operation can be performed on Local Area Connection while it has media disconnected. Let me stress that no changes were made to the laptop at all, it is simply not connecting following the firmware update and password change. All other computers, and phones, 6 in total, are all working fine from simply changing the password.
I returned to work and found a note that my Outlook and Windows password had been changed during the night by the IT department. Why would they need to change my password? Are they monitoring my work somehow.
View 1 Replies View RelatedI changed my password to my wireless connection and now I can't change it in my laptops network settings
View 7 Replies View RelatedI have a Linksys E3000, have had it successfully connected for three months now. Recently I attempted to connect my xbox 360 to the wifi and had issues connecting it. So I called ATT to obtain the PPPoE username and password, which they reluctantly gave me. Entered that into the xbox and still unable to connect, so I have given up on the xbox for the time being, I'll post that issue in a different forum. Where my issue is now is since contacting ATT the WPA2 password I set up for the router no longer works. I cannot access the router setup page, and I cannot add any new wifi devices. Although, all of the previously connected wifi devices are still connected to the router despite this issue. Is there anyway to make the old password work, or do I have to reset the router and start from scratch, and God forbid contact ATT again?
View 2 Replies View RelatedRecently, I bought the E3200, and tried to configure its ports for gaming. Yet, whenever I would hit save settings, it would say my settings were saved, then return me to the settings page. But the settings would be blank. I tried downloading firmware from the website (which should say September 28), yet it still says I am running the firmware from September 1st, even after I applied the upgrade and followed through with the 50 second reboot process.
So, I guess my final question for any tech savvy person out there is "What is wrong with my router/firmware?" I am running the browser config in the most recent Firefox on the same MacBook I used to install the router, and haven't changed any settings other than the SSID and password.
I have a WUSB11 Wireless B and wonder if it accepts WPA2 security, I originally had my router set to WPA, and the wireless B worked fine, I have since changed to WPA2 and notice the Wireless B device won't connect.
View 8 Replies View RelatedIn my laptop WLAN is showing disabled from Device Manager & no Wireless is showing in the Network Adaptar under Device manager.
View 5 Replies View Relatedconfiguring AAA on 1841 router, initially it authenticates me well using my TACAS+ login. but though i have configured enable password in router, router directly puts me in privilage mod without asking enable password .
my configs for AAA as below
aaa authentication login ACS group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization exec ACS group tacacs+ local
aaa authorization commands 0 ACS group tacacs+ local
aaa authorization commands 15 ACS group tacacs+ local
aaa accounting commands 1 ACS start-stop group tacacs+
aaa accounting commands 15 ACS start-stop group tacacs+
how to enable the password on d-link di-624
View 2 Replies View RelatedHow to configure authentication of enable password using acs 5.3. I have installed acs 5.3 and created user and gave relevant passwords. Following config is done on router
aaa new-model
aaa authentication login default group tacacs+ local
aaa authen enable default group tacacs+ enable
tacacs-server host x.x.x.x key xxxxx
Now when I telnet router, i can authenticate username/pass with acs5.3 but when i try to enter enable command and give password, it gives me error in authentication. What is the process of configuring enable passwords?
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
I have a cisco 1801 router that is not prompting for enable password.After loging into router thru telnet it puts direct into privelege mode without promting for enable password.Here is the configuration:
User Access Verification
Username: adminPassword:xxxxx#sh runBuilding configuration...
Current configuration : 2132 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname xxxxxx!boot-start-markerboot-end-marker!enable password 7 022F0A5D0208063555692B!no aaa new-model!!dot11 syslog!!ip cefno ip dhcp use vrf connectedip dhcp excluded-address 192.168.0.1 192.168.0.10!ip dhcp pool LAN import all network 192.168.0.0 255.255.255.0 default-router 192.168.0.1!!!multilink bundle-name authenticated!!username admin privilege 15 password 7 112017031E1C02181Dusername user privilege 3 password 7 091D1C5A100B111B05051033!!archivelog config hidekeys!!!!!interface ATM0no ip addressno atm ilmi-keepalivepvc xxxxx
[code].....
I have migrated my ACS data from 4.1 to 5.1 and everything is working fine to test the connection I have configured a switch to get the authentication from the new Tacacs server, using my old username and password..i got in perfectly but when the switch asked my for enable which is the same password, it refused the password.(I have unchecked the <use a different password for enable> option) I deleted my switch from the Tacacs to enter locally, I went in with no problems..i thought that the problem may be from the old configuration.so I created a new username and password to check, and the problem still exist.
View 2 Replies View RelatedWe are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
View 3 Replies View RelatedI have an e1200 Linksys router hooked up and working well, a wired connection to my first computer a wireless connection to my second (laptop) in the basemen and to my HDTV. My question is what Linksys device would I need to enable me to get a wireless connection in the basement to then hardwire connections to my Blue-Ray player and my HK AVR-3650.
View 2 Replies View RelatedCisco 7609 Router, Enable password unable to reset.
Many times CTRL+BREAK Key combination while booting the router does not takes the console to ROMMON.
Router boots using the IOS image in the bootdisk0: (For entering into the ROMMON, removed both the external Flash disks also - no use)
2 or three time in a day it enters in to the ROMMON while pressing CTRL+BREAK.
Tried in the ROMMON (one Sup is removed) with confreg 0x2142 followed by reset/boot commands, the router is booting with the startup config.
I have been experimenting with acs 4.2 and a cisco asa 5510. I have managed to authenticate the ASA users with my tacacs server. The user "test" is authenticated with the tacacs server, and can log in. But the enable password is wrong, because i dont know where to place it in the tacacs server.
Now my question is, where do i set my enable password when authenticatig with tacacs+. And for this i mean in the acs 4.2, i know how to do it on the asa.
Since I changed the password on my wireless router{linksys}, my desktop is fine but both laptops cannot find network connection. when I ipconfig/all I get "media disconnected" and no ip address.
View 1 Replies View Related