Cisco :: AAA Enable Password Not Working?
Sep 12, 2011
configuring AAA on 1841 router, initially it authenticates me well using my TACAS+ login. but though i have configured enable password in router, router directly puts me in privilage mod without asking enable password .
my configs for AAA as below
aaa authentication login ACS group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization exec ACS group tacacs+ local
aaa authorization commands 0 ACS group tacacs+ local
aaa authorization commands 15 ACS group tacacs+ local
aaa accounting commands 1 ACS start-stop group tacacs+
aaa accounting commands 15 ACS start-stop group tacacs+
View 8 Replies
ADVERTISEMENT
Oct 11, 2012
I have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies
View Related
Jun 24, 2011
how to enable the password on d-link di-624
View 2 Replies
View Related
Jan 28, 2013
How to configure authentication of enable password using acs 5.3. I have installed acs 5.3 and created user and gave relevant passwords. Following config is done on router
aaa new-model
aaa authentication login default group tacacs+ local
aaa authen enable default group tacacs+ enable
tacacs-server host x.x.x.x key xxxxx
Now when I telnet router, i can authenticate username/pass with acs5.3 but when i try to enter enable command and give password, it gives me error in authentication. What is the process of configuring enable passwords?
View 6 Replies
View Related
Aug 3, 2012
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
View 1 Replies
View Related
Aug 29, 2012
I have a cisco 1801 router that is not prompting for enable password.After loging into router thru telnet it puts direct into privelege mode without promting for enable password.Here is the configuration:
User Access Verification
Username: adminPassword:xxxxx#sh runBuilding configuration...
Current configuration : 2132 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname xxxxxx!boot-start-markerboot-end-marker!enable password 7 022F0A5D0208063555692B!no aaa new-model!!dot11 syslog!!ip cefno ip dhcp use vrf connectedip dhcp excluded-address 192.168.0.1 192.168.0.10!ip dhcp pool LAN import all network 192.168.0.0 255.255.255.0 default-router 192.168.0.1!!!multilink bundle-name authenticated!!username admin privilege 15 password 7 112017031E1C02181Dusername user privilege 3 password 7 091D1C5A100B111B05051033!!archivelog config hidekeys!!!!!interface ATM0no ip addressno atm ilmi-keepalivepvc xxxxx
[code].....
View 7 Replies
View Related
Dec 21, 2012
I have migrated my ACS data from 4.1 to 5.1 and everything is working fine to test the connection I have configured a switch to get the authentication from the new Tacacs server, using my old username and password..i got in perfectly but when the switch asked my for enable which is the same password, it refused the password.(I have unchecked the <use a different password for enable> option) I deleted my switch from the Tacacs to enter locally, I went in with no problems..i thought that the problem may be from the old configuration.so I created a new username and password to check, and the problem still exist.
View 2 Replies
View Related
Oct 23, 2012
Today I wanted to change my passwords on my router Cisco 888e.I connect by telnet my router and access the enable mode.Then, I set my enable password to passwordxxx with the command enable password password1.After a show run, i could see in this config my new password correctly set. Then, I set my enable secret password to passwordxxx (the same) with the command enable secret password password1.I log off the enable mode.Try to log on with the command en but when I type the new or the old password, I receive a 'Access denied' message.
And I'm sure of the new one because on my command line to define it I could see this new password in clear!What are my solutions to access the enable mode again?If I reboot my router, it'll run the previous config file with the old password? I've only worked on the running config file and haven't apply these changes to the nvram.
View 4 Replies
View Related
Mar 15, 2011
We are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
View 3 Replies
View Related
Jul 9, 2012
resetting the disable password on an ASA5505 device
View 9 Replies
View Related
Mar 28, 2011
Cisco 7609 Router, Enable password unable to reset.
Many times CTRL+BREAK Key combination while booting the router does not takes the console to ROMMON.
Router boots using the IOS image in the bootdisk0: (For entering into the ROMMON, removed both the external Flash disks also - no use)
2 or three time in a day it enters in to the ROMMON while pressing CTRL+BREAK.
Tried in the ROMMON (one Sup is removed) with confreg 0x2142 followed by reset/boot commands, the router is booting with the startup config.
View 2 Replies
View Related
Dec 29, 2011
Changed my AD password and now i cannot get into the enable side of the cisco switches on our network (we have no routers).Looking on the logs for the ACS v4.2 I can see the following -
On TACACS+ Accounting you can see the connections which have worked - it the initial tty connections -
When i look in the failed attempts i see the following Auth failed - External DB user invalid or bad password or on another occasion internal error or EAP-TLS or PEAP authentication failed due to unknown CAcertificate during SSL handshake.
View 1 Replies
View Related
Jul 10, 2012
I have been experimenting with acs 4.2 and a cisco asa 5510. I have managed to authenticate the ASA users with my tacacs server. The user "test" is authenticated with the tacacs server, and can log in. But the enable password is wrong, because i dont know where to place it in the tacacs server.
Now my question is, where do i set my enable password when authenticatig with tacacs+. And for this i mean in the acs 4.2, i know how to do it on the asa.
View 4 Replies
View Related
Jul 15, 2011
I've got a weird problem that I can't figure out. I've de-authorized the switch in the RADIUS server to force an ERROR status to test the backup entries in the AAA authentication method list. However, after I do that and try to log in (through ssh), it just prompts me for my username's password and not the enable password. Here's the debug output:
1d02h: RADIUS: Marking server xxx.xxx.xxx.xxx:1812,1813 dead
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No valid server found. Trying any viable server
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No response for id 10
[code]...
View 14 Replies
View Related
May 23, 2011
I try to change password on the ASA 5520 device and its not getting changed.
FW(config)# enable password cisco1234(config)# end
After that I perform a write memory.
But somehow I relogin again the enable password still remain as the old enable password
version : 7.2(5)2.
View 5 Replies
View Related
Jan 24, 2013
how do I setup an enable password for an ASA 5510? At the moment its setup to authenticate using RADIUS (which I'd like to keep doing) but I need to setup an enable mode password.
View 3 Replies
View Related
Jul 26, 2012
I am trying to migrate an ACS 4.1.1(24) using the migraton tool to ACS 5.2. The tool is working OK. It migrates the users, groups, NDG, etc. and the reports are showing no errors.
The problem is with the Enable password of the users. The users in the ACS 4 have the TACACS+ Enable Password configured, but after the migration it appears empty in the ACS 5.
View 3 Replies
View Related
Jul 13, 2011
Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies
View Related
Jan 17, 2012
I was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
View 12 Replies
View Related
Jun 17, 2011
how do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies
View Related
Jun 23, 2011
Recently I came across a router (Cisco 3845, IOS 12.4) configured for TACACS, one local username and an enable password. Going through the configuration I noticed the router didn't have an enable secret password which I thought was strange. The TACACS config is below, comments regarding the TACACS config and the consequences of not having an enable secret or if there is a need for one.
aaa authentication login default group tacacs+ aaa authentication login no_tacacs enable aaa authorization exec default group tacacs+ aaa authorization commands 1 default group tacacs+ aaa authorization commands 15 default group tacacs+ aaa accounting exec default start-stop group tacacs+ aaa accounting commands 1 default start-stop group tacacs+ aaa accounting commands 15 default start-stop group tacacs+ aaa accounting network default start-stop group tacacs+
View 7 Replies
View Related
May 2, 2013
I have lost the "ENABLE" password on my 3750 switch.
View 5 Replies
View Related
Jun 30, 2007
I have a BEFSR41v3 and am trying to enable UPnP on the router. However, after I activate UPnP in my browser and the webpage reloads (after the common status screen that says you have to wait 5 seconds and you will be redirected). I am prompted for a password. But for some reason, it will not accept any password that I enter. In order to even get to the settings to UPnP in the first place, you must enter the correct password to access the settings. So I believe I am using the correct password, so why is it not accepting the correct password? I have had to reset my router to factory default settings (by pressing and holding the reset button for 30 seconds) multiple times because of this. But each time after enabling UPnP it will not accept the default password of admin nor will it accept any password that I assign it afterwards. I have noticed however that the "Filter Internal NAT Redirection" which should be set to enabled by default has been set to disabled even after I have reset the router. I have activated UPnP on the router before without trouble but have had to reset the router to factory default settings afterwards because of other reasons.
View 9 Replies
View Related
Aug 10, 2011
I have a customer with a 861 ISR.I want to block all the privilege 0 users from access the enable command
If i telnet into the device, as a priv=0, enable does not work
If i telnet into the device, as a priv=15, enable does work
If i telnet into the device, as a priv=0, enable does not work
If i telnet into the device, as a priv=15, enable does not work
I have issued the command:privilege exec level 15 enable Should block everyone except 15's from accessing the enable command SSH and TELNET are on the same vty:
line con 0
login authentication local_authen
no modem enable
line aux 0
line vty 0 3
[code]....
Basically TELNET is following the rules ( priv=0 not allowed to access enable ) but SSH is not following the rules ( both priv=15 and priv=0 cannot access the command ) is there a way from blocking somes users from login in completely?
View 9 Replies
View Related
Nov 27, 2011
I have a 4404 running firmware 7.0 and something happened (don't think it was a hack), but all of a sudden I can't login to the box via web or ssh or even telnet.
In trying the recovery procedure, I get a lot of messages scrolling through and cannot do the Restore-Password command on the CLI.
I'm attaching the whole capture, but here's a truncated capture from the procedure:
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
[Code].....
So as you can see, my prompt to enter the command is taken up by this fp_main message and it uses up the first and only time I can enter this in. I'm trying everything I can to not have to go back to factory defaults.
View 24 Replies
View Related
Nov 29, 2011
I am in the process of moving in my new house and the landlord set up a Belkin router and gave us the password. I connected to the wifi with no problems on my iphone, but when I try to connect from my PC is says the security key is invalid. I hooked up directly to the router, went to the IP and tried logging in with the password to no avail. I don't get what the problem is? The password works fine from my phone, but not from the computer.
View 10 Replies
View Related
Aug 25, 2011
I have configured under Administration password policies about password lenght, items to be putted as number, letters and so on.on the second tab is the password expire for users and I configured to expire after 90 days.
I even tried creating a new user and changing a password from an existing user using Apache TOMCAT WAR,I have checked CLOCK of ACS appliance and setted up NTP on our internal NTP servers
even I create a new user or I change the password via Admin GUI or I change the user password via Apache TOMCAT WAR, I have the user being disabled in a few of minutes, half an hour.,As last, with CISCO AnyConnect is possible to warn the user about the password being expireing and if so, the change could be driven via AnyConnect or is absolutely needed a User Hand Task on the Apache TOMCAT portal I setted up with the ACS WAR application?
View 6 Replies
View Related
Nov 29, 2011
i have set mywifi router but when i put the same password in my nokia E63 it says invalid for wpa?
View 1 Replies
View Related
May 15, 2012
Recently purchased a new computer and need to remap to our network drive. the password to the drive is not working so i need to change it.
View 1 Replies
View Related
Mar 5, 2012
my password isn't working for wireless router hookup.
View 1 Replies
View Related
Apr 24, 2011
I have a Lynksys WRT54G wireless router. It works just fine until I try to put a password on it. I go through the basic steps, it talkes all my information and tells me everything is good. I try to sign on the internet and it tells me my password is invalid....and YES Im sure its the right password I entered. I went to http://192.168.1.1/wireless.htm and did all the necessary instructions, and still, it doesn't work. I can change my network name and it works. As long as I leave it unprotected, everything works fine, but when I add the password, it tells me its invalid. I even used 123456 so as to make sure it was the right one.
View 5 Replies
View Related
Aug 17, 2011
I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.
I also have a Cisco Aironet AP1242AG that is doing the same thing.
View 7 Replies
View Related
Oct 30, 2011
We were unable to login to a 3825 with a known good password, so we used Cisco's Password Recovery Procedure for that device. We were successful in resetting the password, and had access to the CLI. However, when we logged out of the router, then attempted to log back in, the 'Invalid Password' prompt again came up.We have to use password recovery each and every time we need to access the CLI. Might this be an NVRAM problem?
Show version for this device is: C3825-advsecurityk9-m 12.4(3a).
View 2 Replies
View Related
