How To Enable The Password On D-link Di-624
Jun 24, 2011how to enable the password on d-link di-624
View 2 Replies
ADVERTISEMENT
AAA/Identity/Nac :: Enable Password In ACS 5.3?
Jan 28, 2013How to configure authentication of enable password using acs 5.3. I have installed acs 5.3 and created user and gave relevant passwords. Following config is done on router
aaa new-model
aaa authentication login default group tacacs+ local
aaa authen enable default group tacacs+ enable
tacacs-server host x.x.x.x key xxxxx
Now when I telnet router, i can authenticate username/pass with acs5.3 but when i try to enter enable command and give password, it gives me error in authentication. What is the process of configuring enable passwords?
Cisco :: AAA Enable Password Not Working?
Sep 12, 2011configuring AAA on 1841 router, initially it authenticates me well using my TACAS+ login. but though i have configured enable password in router, router directly puts me in privilage mod without asking enable password .
my configs for AAA as below
aaa authentication login ACS group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization exec ACS group tacacs+ local
aaa authorization commands 0 ACS group tacacs+ local
aaa authorization commands 15 ACS group tacacs+ local
aaa accounting commands 1 ACS start-stop group tacacs+
aaa accounting commands 15 ACS start-stop group tacacs+
Cisco :: Enable Password Recovery In 2950 With AAA?
Aug 3, 2012I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
Cisco WAN :: 1800 Is Not Prompting For Enable Password?
Aug 29, 2012I have a cisco 1801 router that is not prompting for enable password.After loging into router thru telnet it puts direct into privelege mode without promting for enable password.Here is the configuration:
User Access Verification
Username: adminPassword:xxxxx#sh runBuilding configuration...
Current configuration : 2132 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname xxxxxx!boot-start-markerboot-end-marker!enable password 7 022F0A5D0208063555692B!no aaa new-model!!dot11 syslog!!ip cefno ip dhcp use vrf connectedip dhcp excluded-address 192.168.0.1 192.168.0.10!ip dhcp pool LAN import all network 192.168.0.0 255.255.255.0 default-router 192.168.0.1!!!multilink bundle-name authenticated!!username admin privilege 15 password 7 112017031E1C02181Dusername user privilege 3 password 7 091D1C5A100B111B05051033!!archivelog config hidekeys!!!!!interface ATM0no ip addressno atm ilmi-keepalivepvc xxxxx
[code].....
Cisco AAA/Identity/Nac :: ACS 5.1 Is Refusing To Use Enable Password
Dec 21, 2012I have migrated my ACS data from 4.1 to 5.1 and everything is working fine to test the connection I have configured a switch to get the authentication from the new Tacacs server, using my old username and password..i got in perfectly but when the switch asked my for enable which is the same password, it refused the password.(I have unchecked the <use a different password for enable> option) I deleted my switch from the Tacacs to enter locally, I went in with no problems..i thought that the problem may be from the old configuration.so I created a new username and password to check, and the problem still exist.
View 2 Replies View RelatedCisco WAN :: 888e Enable Password Changed
Oct 23, 2012Today I wanted to change my passwords on my router Cisco 888e.I connect by telnet my router and access the enable mode.Then, I set my enable password to passwordxxx with the command enable password password1.After a show run, i could see in this config my new password correctly set. Then, I set my enable secret password to passwordxxx (the same) with the command enable secret password password1.I log off the enable mode.Try to log on with the command en but when I type the new or the old password, I receive a 'Access denied' message.
And I'm sure of the new one because on my command line to define it I could see this new password in clear!What are my solutions to access the enable mode again?If I reboot my router, it'll run the previous config file with the old password? I've only worked on the running config file and haven't apply these changes to the nvram.
Cisco WAN :: RSP720 Default Enable Password
Mar 15, 2011We are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
View 3 Replies View RelatedCisco VPN :: Resetting Enable Password On ASA5505 Device
Jul 9, 2012resetting the disable password on an ASA5505 device
View 9 Replies View RelatedCisco WAN :: 7609 - Enable Password Unable To Reset?
Mar 28, 2011Cisco 7609 Router, Enable password unable to reset.
Many times CTRL+BREAK Key combination while booting the router does not takes the console to ROMMON.
Router boots using the IOS image in the bootdisk0: (For entering into the ROMMON, removed both the external Flash disks also - no use)
2 or three time in a day it enters in to the ROMMON while pressing CTRL+BREAK.
Tried in the ROMMON (one Sup is removed) with confreg 0x2142 followed by reset/boot commands, the router is booting with the startup config.
Cisco Firewall :: ASA5510 Enable Password Not Working
Oct 11, 2012I have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS V4.2 Changed AD Password Now Can't Get Into Enable Side
Dec 29, 2011Changed my AD password and now i cannot get into the enable side of the cisco switches on our network (we have no routers).Looking on the logs for the ACS v4.2 I can see the following -
On TACACS+ Accounting you can see the connections which have worked - it the initial tty connections -
When i look in the failed attempts i see the following Auth failed - External DB user invalid or bad password or on another occasion internal error or EAP-TLS or PEAP authentication failed due to unknown CAcertificate during SSL handshake.
Cisco AAA/Identity/Nac :: 5510 - How To Enable Password When Using Tacacs+
Jul 10, 2012I have been experimenting with acs 4.2 and a cisco asa 5510. I have managed to authenticate the ASA users with my tacacs server. The user "test" is authenticated with the tacacs server, and can log in. But the enable password is wrong, because i dont know where to place it in the tacacs server.
Now my question is, where do i set my enable password when authenticatig with tacacs+. And for this i mean in the acs 4.2, i know how to do it on the asa.
Cisco :: Enable Password Fails In AAA Authentication Method List?
Jul 15, 2011I've got a weird problem that I can't figure out. I've de-authorized the switch in the RADIUS server to force an ERROR status to test the backup entries in the AAA authentication method list. However, after I do that and try to log in (through ssh), it just prompts me for my username's password and not the enable password. Here's the debug output:
1d02h: RADIUS: Marking server xxx.xxx.xxx.xxx:1812,1813 dead
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No valid server found. Trying any viable server
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No response for id 10
[code]...
Cisco Firewall :: On ASA 5520 Device Enable Password Is Not Getting Changed
May 23, 2011I try to change password on the ASA 5520 device and its not getting changed.
FW(config)# enable password cisco1234(config)# end
After that I perform a write memory.
But somehow I relogin again the enable password still remain as the old enable password
version : 7.2(5)2.
Cisco AAA/Identity/Nac :: How To Setup Enable Mode Password On ASA 5510
Jan 24, 2013how do I setup an enable password for an ASA 5510? At the moment its setup to authenticate using RADIUS (which I'd like to keep doing) but I need to setup an enable mode password.
View 3 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 Migration Utility TACACS+ Enable Password
Jul 26, 2012I am trying to migrate an ACS 4.1.1(24) using the migraton tool to ACS 5.2. The tool is working OK. It migrates the users, groups, NDG, etc. and the reports are showing no errors.
The problem is with the Enable password of the users. The users in the ACS 4 have the TACACS+ Enable Password configured, but after the migration it appears empty in the ACS 5.
Linksys Wired Router :: BEFSR41v3 Enable UPnP / Password Not Accepted
Jun 30, 2007I have a BEFSR41v3 and am trying to enable UPnP on the router. However, after I activate UPnP in my browser and the webpage reloads (after the common status screen that says you have to wait 5 seconds and you will be redirected). I am prompted for a password. But for some reason, it will not accept any password that I enter. In order to even get to the settings to UPnP in the first place, you must enter the correct password to access the settings. So I believe I am using the correct password, so why is it not accepting the correct password? I have had to reset my router to factory default settings (by pressing and holding the reset button for 30 seconds) multiple times because of this. But each time after enabling UPnP it will not accept the default password of admin nor will it accept any password that I assign it afterwards. I have noticed however that the "Filter Internal NAT Redirection" which should be set to enabled by default has been set to disabled even after I have reset the router. I have activated UPnP on the router before without trouble but have had to reset the router to factory default settings afterwards because of other reasons.
View 9 Replies View RelatedCisco Firewall :: ASA 5505 / Lost Enable Password For Spare Device?
Jul 13, 2011Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies View RelatedCisco Wireless :: AIR-AP1142N-A-K9 Set To Factory Default But Enable Password Not Reset
Jan 17, 2012I was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
Cisco Firewall :: 5570 - How To Change Telnet And Enable VPN User Password
Jun 17, 2011how do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies View RelatedCisco AAA/Identity/Nac :: 3845 - Enable Secret Password Missing In Configuration
Jun 23, 2011Recently I came across a router (Cisco 3845, IOS 12.4) configured for TACACS, one local username and an enable password. Going through the configuration I noticed the router didn't have an enable secret password which I thought was strange. The TACACS config is below, comments regarding the TACACS config and the consequences of not having an enable secret or if there is a need for one.
aaa authentication login default group tacacs+ aaa authentication login no_tacacs enable aaa authorization exec default group tacacs+ aaa authorization commands 1 default group tacacs+ aaa authorization commands 15 default group tacacs+ aaa accounting exec default start-stop group tacacs+ aaa accounting commands 1 default start-stop group tacacs+ aaa accounting commands 15 default start-stop group tacacs+ aaa accounting network default start-stop group tacacs+
Cisco Switching/Routing :: 3750 Switch - Lost Enable Password
May 2, 2013I have lost the "ENABLE" password on my 3750 switch.
View 5 Replies View RelatedEnable Security On Dir 615 D-link?
Sep 4, 2011I have D-Link wireless N Home Router.How do i enable security on DIR-615
View 1 Replies View RelatedD-link Dir-655 :: Disable / Enable Wifi To Script Possible?
May 3, 2012I want know if it's possible with a script enable disable wifi, without every time login to router.
View 1 Replies View RelatedD-Link DAP-1522 :: How To Enable 5Ghz Band
Oct 13, 2011I installed my 1522 today with a Direct TV receiver and made a connection using AP mode.
How do I know what band is being used and how to switch between the bads.
D-Link DIR-825 :: How To Enable SPI Firewall And Wireless MAC Filtering
Jan 23, 2013Where on my router interface I could go to enable both the SPI Firewall, and the Wireless MAC Filtering? I have the D-link DIR-815.
View 1 Replies View RelatedD-Link DIR-600 :: Doesn't Allow To Enable Wireless MAC Filtering
May 20, 2011DIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)
View 1 Replies View RelatedD-Link WBR-1310 Enable Wired Network Adapter?
Feb 1, 2013New pc that i built, everything works properly but the internet connection...Windows said i needed the drivers for my router, so i tryed installing them but it said Enable Wired Network Adapter and said to retry after. I don't know what it's talking about. Router is D-Link WBR-1310.
View 4 Replies View RelatedD-Link DAP-1522 :: How To Enable JTAG Mode On DAP-1160
Jan 24, 2011I have a dead DAP-1160 (RTL8186). I would try the JTAG recovery, so I compiled
-) includes-0.4.2
-) readline-5.2
-) jtag-0.6-cvs-20051228
under ubuntu 10.10.I have the cable DLC5 Xilinx.The problem is: I do not know how to enable the JTAG mode on the DAP-1160.I understand that I must set a pin on the 147 on the RTL8186. but I have no idea where is on the DAP-160 PCB.
D-Link DIR-655 :: Enable Mac Address Filtering Only For The Wireless Side?
Sep 3, 2011It shows this option "Filter wireless clients: Apply MAC Filtering to devices that connect to the network via Wi-Fi. This is the normal usage of MAC Filtering. Filter wired clients: "However I don't see that option on the actual page. How can i enable Mac address filtering only for the wireless side?
View 7 Replies View RelatedD-Link DIR-825 :: High Ping Spikes When Enable DNS Relay Is Ticked
Apr 30, 2013I was having very high ping spikes (up to 2000ms) in my online gaming. I even had high spikes (up to 80ms) just pinging my router. It happened with every computer on the network. After several weeks, I narrowed it down to one thing: Enable DNS Relay. I unticked that, and instantly the spikes went away. However, my brother's Blackberry Playbook has been acting up now that DNS Relay is disabled. Basically, every day, the internet on that thing screeches to a halt, forcing him to reconnect to the network. It's basically a minor inconvenience, but it's one I want to correct. If I turn on DNS Relay again, the ping spikes will return. Interestingly, I switched ISPs during this time. I'm on cable now. I used to be on DSL with a different router, yet I had the exact same problem. The blackberry is probably integral to this problem. So I'd like to know if there's anything I can do to make DNS Relay work properly, allowing his stupid Blackberry to work, while maintaining the integrity of the network.
View 5 Replies View RelatedTP-Link Dual-Band Wireless :: TL-WDR4300 Unable To Enable Ftp Over Internet
Feb 15, 2013Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : : 3.13.17 Build 120426 Rel.29216n
ISP : Sky
I am trying to setup my ftp site.My internet address appears as FTP Server Configuration
Server Status: Started
Internet Access: EnableDisable
Service Port: (The default is 21, do not change unless necessary.)
Internet Address: 192.168.0.3
How does my ftp site get active, it keeps the 192.168.0.3 address.I have enabled and saved hoping this will allow it, but no joy.