Cisco Switching/Routing :: 3750 Switch - Lost Enable Password
May 2, 2013I have lost the "ENABLE" password on my 3750 switch.
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Enable / Disable OID's In Catalyst 3750-X Switch
Feb 19, 2013In my ongoing project i need to monitor cisco 3750-X port status (uplink/downlink) i.e. whenever there is some problem at a specific port. I need to monitor it through an OPC server and right now what i am doing is as follows: i am using Kepserver and i have added SNMP driver in it for that purpose i am not a networking expert but what i have learnt till now is that SNMP agent (that resides in switch) delivers the status of MIBs to SNMP manager ( which in my case is kepserver (opc server)) for the above purpose i am adding IF-MIB to monitor OID 1.3.6.1.2.1.2.2.1.8 (which shows port statuses) but when i add that in OPC server then it indicated that this OID is not available in the Switch ( it might be disabled) so i need to ask if there is any way to enable OID's in a switch,
View 0 Replies View RelatedCisco Switching/Routing :: Set Username / Password On 3750 Switch?
Nov 24, 2012I want to configure " Username & Password" on Cisco 3750 switch. I need to configure as "username xxxxxx privilege 15 password 5 xxxxxxx "
Is it possible to create password with level 5 ? I want to know about level 5 "password" & level 7 "password" ?
when i tried I am not able to configure with " password 5"
Cisco Switching/Routing :: How To Recover Password On 3750 Switch
Nov 25, 2008Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 19-Jul-07 19:15 by nachen
Image text-base: 0x00003000, data-base: 0x01280000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEE4, RELEASE SOFTWARE (fc1)
Cisco Switching/Routing :: 3750 - Username And Password On New Switch?
Jun 17, 2012In a new Cisco 3750, if the username and password is not configured seperately, what will be the default username & password. I have only configured enable password. when we access it remotely via telnet it prompts for username/password.
View 3 Replies View RelatedCisco Firewall :: ASA 5505 / Lost Enable Password For Spare Device?
Jul 13, 2011Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies View RelatedCisco Switching/Routing :: How To Enable NetFlow On 3750
Mar 17, 2013I have a 370 with C3KX-NM-10G module & i want to enable NetFlow on it did the specified configs
Step 1 Flexible NetFlow Flow Recordsflow record miketestmatch datalink source-vlan-idmatch datalink dot1q prioritymatch datalink mac source-addressmatch datalink mac destination-addressmatch ipv4 versionmatch ipv4 tosmatch ipv4 ttlmatch ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch transport source-portmatch transport destination-portmatch interface input physical snmpcollect interface output snmpcollect counter flowscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime last flow record miketestegressmatch datalink destination-vlan-id match datalink dot1q priority match datalink mac source-address match datalink mac destination-address match ipv4 version match ipv4 tos match ipv4 ttl match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port match interface output physical snmp collect interface input snmp collect counter flows collect counter bytes collect counter packets collect timestamp sys-uptime first collect timestamp sys-uptime last Step 2 Flexible NetFlow Flow ExporterFlow exporter export-to-samplicatorDestination 10.1.1.8source Vlan1Transport udp 2055option interface-table timeout 60 Step 3 Flexible NetFlow Flow Monitors# Tie the Flow Monitor to the Flow Recordflow monitor mikektestrecord miketestexporter export-to-samplicatorcache timeout active 60flow monitor mikektestegressrecord miketestegressexporter export-to-samplicatorcache timeout active 60
& Applied it to g1/1/1 but without any luck , if netflow works on the
TenGigabitEthernet1/1/1 &
TenGigabitEthernet1/1/2
Only i have four switches stacked and nothing plugged to the
C3KX-NM-10G module
Cisco Switching/Routing :: 3750 - How To Enable SFP Port
Nov 7, 2011I am trying to configure a 3750 48 port switch and having trouble with getting it to see the sfp. I just want to set up the router with a pretty basic set up since I am using it for a ping test between 2 buildings, via fiber. How I can enable the sfp port?
View 3 Replies View RelatedCisco Switching/Routing :: 3750 - Enable SNMP On Switches?
Dec 26, 2011I want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
Cisco Switching/Routing :: 3750 - Enable EIGRP Process
Sep 23, 2012I have a hub and spoke WAN that conisits of one core location with with a 6500 and nine other buildings using 4006 Catalyst that conenct back to the core via dual gig fiber. We are using EIGRP at each location as well as the core. I was tesing something at one of our buildings decided to hang a 3750 off the 4006 and enable the same eigrp process on the 3750 that is enabled on the 4006 and 6500 (EIGRP 1).
1. All the routes that the 6500 knows about are advertised out to each of the nine locations.
2. The 4006's are all advertising thier directly conencted routes to the 6500.
Onto the location I was testing at:
The 4006 where I was testing at has four vlan interfaces enabled and they are in an UP/UP state. The ip routes from the 4006's directly conencted vlan interfaces propogate to the 6500 at our core location and the 6500 sucsefully propgates these learned routes to all the other 4006's.
This past Friday I configured a 3750x with two /22 vlan interfces and one physical gi port with an IP address and also configured on Ethernet port on the 4006 with an IP address in the same network block as the 3750x gi interface (a /30 netowrk block). I saw both interfaces come up and EIGRP sucesfully established a neighbor adjecency between the 3750x and the 4006.
I noticed that the 3750 advertised out all of it's directly conencted routes to the 4006 and the 4006 advertised it's directly conencted routes to the 3750. However, the 4006 did not advertise any of the routes it had learned from the 3750x to the 6500 and nor did the 4006 advertise any of the routes it had learned from the 6500 to the 4006. My suspicion is that the "eigrp stub connected summary" statement is enabled on both the 4006 and 3750 thus prevenintg them form advertising out any routes other than thier directly conencted routes. Can any of you verify that I'm either correct or inccorect about this?
here are the eigrp statemnets from the 6500 and 4006:
6500:
router eigrp 1
redistribute static
network 10.0.0.0
network 172.16.0.0
network 172.17.0.0(code)
Cisco Switching/Routing :: 3750 Router Lost Power And Rebooted
May 14, 2012I am new to this and have ran into some problems. I butilt up my router I was able from the rom> prompt to get my router to boot from SLOT0:xxxxx
Then I did the copy command copy slot0:xxxxxxx bootflash:xxxxxxxMy router starts up fine. I did all my configurations and did my copy run start when I was done. As this is what I do on my 3750s.
My router lost power and rebooted and I lost everything it did not boot up to my last configuration.How do I save my configurations when I am done ? How do I get it to boot from that configuration every time?
Cisco Switching/Routing :: 3750 - Cannot Enable PBR On A VLAN WCCP Enabled
Jan 3, 2012I would like to apply a policy-based route on one of our L3 switches (Cisco 3750) to change the next-hop of a couple of servers only. The VLAN where those servers reside got WCCP enabled on it. When I want to apply the route-policy to that VLAN interface it doesn't let me. When I try to apply the same policy to a VLAN interface without WCCP it does work. Is there any Cisco IOS limitations that would prevent me from doing that?
Configuration:
route policy config:
access-list 70 permit ip host x.x.x.x (server IP)
route-map PBR1 permit 10
[Code].....
Cisco Switching/Routing :: 3750-x / Separate Module To Enable Stackwise And Stackpower?
Aug 22, 2012As I understand Cisco Catalyst 3750-x supports stackwise and stackpower technology.Do I need to purchase a seperate module to enable stackwise and stackpower? Or are stackwise and stackpower modules included be default on the switch already?
View 4 Replies View RelatedCisco Switching/Routing :: 3750 / 3800 - Configure Trunk Between Switch And Extreme Switch
Nov 2, 2011i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedCisco Switching/Routing :: 3750-X Stacking Switch By Switch
Nov 18, 2012I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedCisco Switching/Routing :: 2960 Switch Lost Configuration
May 5, 2013I have a 2960 that bounced several times over the weekend and then appears to have lost its configuration. Using CDP from the backbone switch pulls up the information below. Is there any way for me to configure the downed switch from another switch on the network? I am trying to avoid having someone from the site try to find a console cable and a suitable computer with a serial port. [code]
View 2 Replies View RelatedCisco :: 3750 Switch - Connectivity Lost For Some Ports?
Mar 8, 2013In my 3750 stack switch there are more than 10 L3 vlans currently in use.In that only one vlan for example vlan 11 (we given up link directly to the nodes connected to that ports which is in vlan 11)losing connectivity for sometime and again connectivity restored.Except Vlan 11 all other vlans are working fine. When we troubleshooted the issue some of the ip's able to ping and some not able to ping. checked the interface status of that ports (no crc and input errors) and port is in up status only.we also checked cpu utlilisation ,device uptime, all are no issues found. am sharing my sw basic config and one interface status at the time of issue.But only one port learning more than 50 Mac-Addresses dynamically.and am learning mac address violation in another port which is port security and storm control enabled on that port..Its seems to be any attack or something else????
interface GigabitEthernet1/0/20
--More-- description
switchport access vlan 11
switchport mode access
spanning-tree portfast
logs:
Mar 8 05:58:25.848 IST: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0026.0a18.8218 on port GigabitEthernet1/0/16.
Mar 8 05:59:25.862 IST: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0026.0a18.8218 on port GigabitEthernet1/0/16.
AT the time of issue interface status:
sh int gi2/0/14
GigabitEthernet2/0/14 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0026.ca46.5c8e (bia 0026.ca46.5c8e)
Description:
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,[code]......
Cisco Switching/Routing :: How To Enable Ssh On 4507 Distribution Switch
Jan 30, 2013We have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies View RelatedCisco Switching/Routing :: 4900m Switch Enable HTTP
Jan 6, 2013I have been trying to get the http server enabled so I can access Cisco Network Assistant. I have my interfaces configured but for some reason the server in not running, port 80 is still closed. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Enable Dhcp Service On 3560 Switch
Mar 19, 2012can you enable dhcp service on a 3560 switch.
View 3 Replies View RelatedCisco Switching/Routing :: ASA 5510 - Enable IP Accounting In Cre Switch Running Cat OS
Sep 3, 2012How to Enable IP Accounting in Cre switch 4000 Running cat OS and Cisc ASA 5510 (8.2 )
View 1 Replies View RelatedCisco Switching/Routing :: Enable / Disable Interfaces On 3550 Switch
Jul 14, 2012I`m looking to automate some functions in a web application.Functions like enable/disable interfaces on a Cisco 3550 switch.
View 5 Replies View RelatedCisco Switching/Routing :: Enable STP To Specific VLans In 6500 Switch?
Jun 13, 2013I have 6500 with this STP configuration:
spanning-tree mode rapid-pvst
no spanning-tree vlan 1-4094
I need to enable STP on vlan 100 and vlan 103.
When I do "spanning-tree vlan 100,103 root primary" and then "show spanning-tree".I see that STP is not enable on these vlans (100,103).
I tried to do "no spanning-tree vlan 1-99,101,102,104-4094" and it is not work.
There is a way to enable STP on vlans 100,103 without to do "spanning-tree vlan 1-4094"
Cisco Switching/Routing :: 2960 - Enable Snmp For Switch Port
Dec 18, 2011i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedCisco Switching/Routing :: Enable Second Power Supply On 3750x Switch
Nov 6, 2012I have a 3750x 48port POE switch that I installed a second power supply in. But it doesnt power on. Am I supposed to enable it in the switch somewhere? I've plugged it into a couple different outlets so I know that's not the problem.
View 4 Replies View RelatedCisco Switching/Routing :: 3750 Password Recovery
Sep 24, 2012I want to recover the password or set the cisco 3750 to the default password, as forget it
View 4 Replies View RelatedCisco Switching/Routing :: 3750 Prompt For Password Change
Feb 6, 2013I recently configured a cisco 3750 switch for a stand alone network here at work, and on all our other switches and routers we use ACS to access everything. This switch being a stand alone I dont have that option.
So being like that I have to create everyone in the shop a username and password. Is there a way to prompt the user to change their password on their first login like you would with windows or such?
Cisco Switching/Routing :: 3750 Username And Password Via SNMP?
Sep 24, 2012Is there anyway to pull the usernames and passwords from a switch via SNMP or write a new username and password to switch via SNMP. I have switch that was apparently misconfigured and i am not feeling like driving all the way down there to console in.
View 2 Replies View RelatedCisco Switching/Routing :: 6509 - 802.1x And Voice VLAN / Enable Dot1x On User's Ports On The Switch
Sep 17, 2012I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
Cisco Switching/Routing :: Inter-VLan Routing On Catalyst 3750 Switch
Dec 17, 2011I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
Cisco Switching/Routing :: 3825 / Replacing Routing Function With 3750 Switch?
Jul 27, 2012I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
Cisco Switching/Routing :: About Intervlan Routing On Catalyst 3750 Switch
Apr 16, 2012I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedCisco Switching/Routing :: Cannot Reach Gateway Through Routing Switch (3750)
Mar 11, 2012I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....