We are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
View 3 RepliesI was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
I've been tasked with setting up a laptop that I would describe as "ancient". It's running XP SP3 right now and it does that rather well. However, there's one issue that I have not yet been able to get rid of and I've been working on this on and off for about a year (luckily, the laptop's owned by a relative, so I'm not on a deadline). However, all lack of deadlines aside, I'm at my wit's end. So here's the issue.Whenever I boot the laptop up, the Wireless Button is disabled. Since this laptop is never going to be moved again, it's very bothersome to always have to push the button, wait for a while and then have it sign in. Here's what I want: I want the laptop to boot up, then automatically link up to the house's own WLAN.
The Wireless connection is handled via Wistron Launch Manager 1.1.0 and the laptop is a Littlebit Coris Z71. I've figured out that an EXE named WButton.exe is responsible for the availability of wireless connections. However, putting a shortcut to this EXE in the Startup-folder of the startmenu hasn't worked either. I also seem to be unable to figure out what process WButton.exe uses or which values it changes, let alone where they're changed. For all I know, the wireless connection is handled by a magical randomness.
I have several WLC 5508 with 7.2.110 firmware. My questions are:
(1) Is band select is enable by default on 7.2.110?
(2) All the variables settings on the band select, how do I set it up to make 5 ghz more preferable than 2 ghz?
Any benefit to enable https with in the gui instead of using the default http?
View 1 Replies View Relatedconfiguring AAA on 1841 router, initially it authenticates me well using my TACAS+ login. but though i have configured enable password in router, router directly puts me in privilage mod without asking enable password .
my configs for AAA as below
aaa authentication login ACS group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization exec ACS group tacacs+ local
aaa authorization commands 0 ACS group tacacs+ local
aaa authorization commands 15 ACS group tacacs+ local
aaa accounting commands 1 ACS start-stop group tacacs+
aaa accounting commands 15 ACS start-stop group tacacs+
how to enable the password on d-link di-624
View 2 Replies View RelatedHow to configure authentication of enable password using acs 5.3. I have installed acs 5.3 and created user and gave relevant passwords. Following config is done on router
aaa new-model
aaa authentication login default group tacacs+ local
aaa authen enable default group tacacs+ enable
tacacs-server host x.x.x.x key xxxxx
Now when I telnet router, i can authenticate username/pass with acs5.3 but when i try to enter enable command and give password, it gives me error in authentication. What is the process of configuring enable passwords?
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
I have a cisco 1801 router that is not prompting for enable password.After loging into router thru telnet it puts direct into privelege mode without promting for enable password.Here is the configuration:
User Access Verification
Username: adminPassword:xxxxx#sh runBuilding configuration...
Current configuration : 2132 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname xxxxxx!boot-start-markerboot-end-marker!enable password 7 022F0A5D0208063555692B!no aaa new-model!!dot11 syslog!!ip cefno ip dhcp use vrf connectedip dhcp excluded-address 192.168.0.1 192.168.0.10!ip dhcp pool LAN import all network 192.168.0.0 255.255.255.0 default-router 192.168.0.1!!!multilink bundle-name authenticated!!username admin privilege 15 password 7 112017031E1C02181Dusername user privilege 3 password 7 091D1C5A100B111B05051033!!archivelog config hidekeys!!!!!interface ATM0no ip addressno atm ilmi-keepalivepvc xxxxx
[code].....
I have migrated my ACS data from 4.1 to 5.1 and everything is working fine to test the connection I have configured a switch to get the authentication from the new Tacacs server, using my old username and password..i got in perfectly but when the switch asked my for enable which is the same password, it refused the password.(I have unchecked the <use a different password for enable> option) I deleted my switch from the Tacacs to enter locally, I went in with no problems..i thought that the problem may be from the old configuration.so I created a new username and password to check, and the problem still exist.
View 2 Replies View RelatedToday I wanted to change my passwords on my router Cisco 888e.I connect by telnet my router and access the enable mode.Then, I set my enable password to passwordxxx with the command enable password password1.After a show run, i could see in this config my new password correctly set. Then, I set my enable secret password to passwordxxx (the same) with the command enable secret password password1.I log off the enable mode.Try to log on with the command en but when I type the new or the old password, I receive a 'Access denied' message.
And I'm sure of the new one because on my command line to define it I could see this new password in clear!What are my solutions to access the enable mode again?If I reboot my router, it'll run the previous config file with the old password? I've only worked on the running config file and haven't apply these changes to the nvram.
resetting the disable password on an ASA5505 device
View 9 Replies View RelatedCisco 7609 Router, Enable password unable to reset.
Many times CTRL+BREAK Key combination while booting the router does not takes the console to ROMMON.
Router boots using the IOS image in the bootdisk0: (For entering into the ROMMON, removed both the external Flash disks also - no use)
2 or three time in a day it enters in to the ROMMON while pressing CTRL+BREAK.
Tried in the ROMMON (one Sup is removed) with confreg 0x2142 followed by reset/boot commands, the router is booting with the startup config.
I have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies View RelatedChanged my AD password and now i cannot get into the enable side of the cisco switches on our network (we have no routers).Looking on the logs for the ACS v4.2 I can see the following -
On TACACS+ Accounting you can see the connections which have worked - it the initial tty connections -
When i look in the failed attempts i see the following Auth failed - External DB user invalid or bad password or on another occasion internal error or EAP-TLS or PEAP authentication failed due to unknown CAcertificate during SSL handshake.
I have been experimenting with acs 4.2 and a cisco asa 5510. I have managed to authenticate the ASA users with my tacacs server. The user "test" is authenticated with the tacacs server, and can log in. But the enable password is wrong, because i dont know where to place it in the tacacs server.
Now my question is, where do i set my enable password when authenticatig with tacacs+. And for this i mean in the acs 4.2, i know how to do it on the asa.
I've got a weird problem that I can't figure out. I've de-authorized the switch in the RADIUS server to force an ERROR status to test the backup entries in the AAA authentication method list. However, after I do that and try to log in (through ssh), it just prompts me for my username's password and not the enable password. Here's the debug output:
1d02h: RADIUS: Marking server xxx.xxx.xxx.xxx:1812,1813 dead
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No valid server found. Trying any viable server
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No response for id 10
[code]...
I try to change password on the ASA 5520 device and its not getting changed.
FW(config)# enable password cisco1234(config)# end
After that I perform a write memory.
But somehow I relogin again the enable password still remain as the old enable password
version : 7.2(5)2.
how do I setup an enable password for an ASA 5510? At the moment its setup to authenticate using RADIUS (which I'd like to keep doing) but I need to setup an enable mode password.
View 3 Replies View RelatedI am trying to migrate an ACS 4.1.1(24) using the migraton tool to ACS 5.2. The tool is working OK. It migrates the users, groups, NDG, etc. and the reports are showing no errors.
The problem is with the Enable password of the users. The users in the ACS 4 have the TACACS+ Enable Password configured, but after the migration it appears empty in the ACS 5.
When doing a backup on any of the ACS 5.x appliances by default the backup is encrypted with PGP. What password is used for that? Is it configurable?
View 3 Replies View RelatedIs there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies View Relatedhow do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies View RelatedRecently I came across a router (Cisco 3845, IOS 12.4) configured for TACACS, one local username and an enable password. Going through the configuration I noticed the router didn't have an enable secret password which I thought was strange. The TACACS config is below, comments regarding the TACACS config and the consequences of not having an enable secret or if there is a need for one.
aaa authentication login default group tacacs+ aaa authentication login no_tacacs enable aaa authorization exec default group tacacs+ aaa authorization commands 1 default group tacacs+ aaa authorization commands 15 default group tacacs+ aaa accounting exec default start-stop group tacacs+ aaa accounting commands 1 default start-stop group tacacs+ aaa accounting commands 15 default start-stop group tacacs+ aaa accounting network default start-stop group tacacs+
I have lost the "ENABLE" password on my 3750 switch.
View 5 Replies View RelatedI have to do a migration of sup32 to RSP720 for which I need to know if you can operate the equipment connected with the 2 supervisors at the same time??? and it still working ?
View 1 Replies View RelatedI have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking abouth the procedure?shall i switch off the router ? or just removeSUP32 and insert RSP720 ?are there any steps should i do before the upgrade ?i am planning to take the router out of service during the operation, how much down time it will be ?
View 9 Replies View RelatedI found that there is no force-switchover command under redundancy configuration mode. How can I do a switchover from primary RSP720 to secondary RSP720?
I am using SSO and NSF.
C7609-2(config)#do sh redundancy
Redundant System Information :
------------------------------
Available system uptime = 1 hour, 51 minutes
[Code]....
I tried to change the default password Cisco to other by command line but the password cannot work out.
The command line I used are as below :
AP#conf tEnter configuration commands, one per line. End with CNTL/Z.AP(config)#enable passAP(config)#enable password 4dMINO123 ?LINE <cr>
[Code].....
How do I change the password from the default for the internet?
View 1 Replies View Relatedanybody let us know the default username and password for the failsafe account of Summit X450e-48p Extreme Networks Switch.
View 4 Replies View RelatedI need to find out the default log in and password for the model 7550
View 1 Replies View Related