I found that there is no force-switchover command under redundancy configuration mode. How can I do a switchover from primary RSP720 to secondary RSP720?
I am using SSO and NSF.
C7609-2(config)#do sh redundancy
Redundant System Information :
------------------------------
Available system uptime = 1 hour, 51 minutes
[Code]....
I have two 4503 switches connected individually two 5510 Asa. My web server is under 5510 dmz interface. From Two 5510 Asa dmz interface there are two cables connected to two individual server farm switches.The web server in connected to this server farm switches.My local lan in connected to a cisco linksys switch. from that two cables are connected two individual 4503 switches on same vlan. i configured hsrp on this vlan. i pings the web server from local lan. when i unplugged one cable from Primary switch then it take 7-8 request timeout to recover into Secondary switch. it takes about 40 sec to switchover. it takes too much time. i also tune the timers but no luck. My Primary switch is also a Root Bridge.
View 7 Replies View RelatedI am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:
1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.
2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.
I have to do a migration of sup32 to RSP720 for which I need to know if you can operate the equipment connected with the 2 supervisors at the same time??? and it still working ?
View 1 Replies View RelatedI have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking abouth the procedure?shall i switch off the router ? or just removeSUP32 and insert RSP720 ?are there any steps should i do before the upgrade ?i am planning to take the router out of service during the operation, how much down time it will be ?
View 9 Replies View RelatedWe are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
View 3 Replies View RelatedHow can we confirm the memory requirement for a RSP720-3c-ge card ?I got a link for 6500 series [URL]
View 2 Replies View RelatedI have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
After inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies View RelatedIs Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies View RelatedI have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies View RelatedI have my Router, not asa, with IOS Easy VPN Server established. If I use split tunneling my clients can access the net all day long and access hosts and resources over the VPN on the other side of the network as if it were plugged into the lan. The hard part I cant figure out is how to force tunnel. I want all internet access to go through the router and not to split tunnel in addition I want to retain the ability to access local resources as if I were plugged into the LAN. I have security reasons for doing this and I am not worried about a little extra load on the router. Let me know where to start looking. I can provide configs if necessary. If I do be warned I am trying to learn what all this nifty Cisco Config Pro GUI can do so my config is gonna be full of all kind of stuff that is messy. I wont post unless asked.
View 1 Replies View RelatedI have a setup with a few sites that have layer three switches behind firewalls. I've been successful in setting up GRE tunnels between all the layer three switches, the GRE traverses IPsec which goes between the firewalls at each site. That way, the GRE is encrypted over the Internet and I don't have to deal with protocol forwarding and stuff. The GRE tunnels are terminated at the loopback addresses of each layer three switch, this works well for the most part, except that I need to put static routes for each loopback address in each switch to point via the firewalls, because when OSPF comes up over the GRE tunnels it starts advertising the loopbacks, and as such the switches think they can get to them over the GRE (which is built from the loopbacks to begin with), as you can see, sort of a catch 22. The static route method works fine, but it makes it so that I can't access the loopback address for monitoring/management purposes from any other sites on the basis that the local core tries to send it directly to the firewall rather than over the GRE tunnel. Is there any way to force only the GRE traffic out via the firewall while letting any other loopback-destined traffic go over the GRE? I'm thinking this could be done with a properly-matching route-map, but I'm not sure where I would apply it, could I apply it directly to the loopback or would the GRE traffic skip that on the way out?
View 7 Replies View Relatedcan I force an IPSEC L2L tunnel to use NAT-T encapsulation no matter what? Automatic detection says none of the endpoints are behind NAT. I know I can disable it by the "crypto map XXX set nat-t-disable" command, but I want the exact opposite.
I have a very strange issue where asynchronos routing is making my life as a technician very hard.
A side question; Can I do something about an ISP that is policy-base-routing its ESP traffic (and/or translating it)?
ASA5505 ===>===>===> ISAKMP traffic ===>===>===> ASA5510
212.178.155.73 80.62.yyy.xxx (traffic source IP: 212.178.155.73)
[Code].....
I want to force a certain program (Max Payne 3) to use the third and forth DNS's that I configured in advanced settings of DNS settings (Windows7).
I want to do this because for some reason, using Google DNS in Turkey makes the game not start forcing me to use the DNS servers of my Internet provider. (if only it tried the second DNS that I configured, it would start but for some reason it does not)
i try to connect to a website i know is opperating but get error timed out 4 out of 5 times
View 1 Replies View RelatedI have made the following change to my ASA 5520 using ASDM to try and force VPN clients to use a self assigned certificate from the ASA. I made the following changes Remove Access VPN > Certificate Management > Identity Certificates > Add Certificate.Then I made the following change.. Remote Access VPN > Network (Client) Access > IPSec(IKEv1) Connection Profiles > Connection Profile > Edit > IKE Peer Authentication > Pre Shared key and pointed the identity certificate to the one I created in the step above.Having made this change I am still able to VPN without a certificate configured in authentication settings.I was expecting that the VPN would attempt to issue the self assigned cert to client machine?
View 1 Replies View RelatedWe are going to be setting up a remote access VPN to a Cisco ASA 5505, once connected to the VPN the internet traffic from the client will then go back out to the internet from the ASA (for web browsing), but Is there anyway to force the traffic through an AV server at the head office site before the traffic goes back out to the internet?
View 5 Replies View RelatedIf so then Wireless N is not a feature of this device, especially for multimedia files that require larger bandwidth. I could have spent far less on a product that would have worked.
View 3 Replies View RelatedI have 3xLAP1242 in a building that are some what close to eachother (WCS show them as Rx Neighbors). The problem is that they are all running the same channel, 1 on 2.4GHz and channel 140 on 5GHz. [code]Ether I get these log messages because they are on the same channel or because there is something blocking the other channels.Can I force a channel change on the LAPs somehow? Not manualy setting the channels, but forcing the LAPs to redo their channel calculation/algorithm.
View 12 Replies View RelatedJust setup two RV220Ws with a IPsec VPN connection. All working well. However, I have a question regarding how to force ALL traffic from a VLAN to go thru the VPN.IPsec from site A (EU) to site B (USA) working good. On Site A I have a dedicated VLAN that needs to have ALL traffic (internet included) be sent thru the VPN tunnel. The main purpose of this is to have internet presence as if in the USA. This is necessary to access some sites available only in USA specially for the kids -their web sites will not display content because they're not in the USA at the moment. How do I accomplish this? I tried to setup a Static Route for the VLAN but you cannot setup a 0.0.0.0 destination route.
View 2 Replies View RelatedI have 2 Cisco 871 set up to vpn in to an ASA 5510. Everything has worked even when the 871 is behind a nat.
We use these routers to send to employees home for temporary use.
The WAN ports on the 871 are configured to pick up an IP via DHCP.
Office ASA 5510 - Public IP address
WAN - Public IP
Internal - 192.168.1.0/24
|
Internet
|
Home Router
WAN - Public IP
Internal - 192.168.1.0/24
|
Cisco 871 picks up 192.168.1.x on WAN port from user's home router
Internal vlan1 192.168.10.x/24
The problem is - this user's home router is using the same subnet as the internal network at the office. Is there anyway to force traffic bound for 192.168.1.x to go over the VPN tunnel? It does this correctly if the 871's WAN port is not also on the same subnet. The vpn tunnel does come up. And I can ping to and from the router, it's just the clients behind the 871 that cannot ping or access the corp network.
I have configured Cisco 1841 router. My problem is what if every first time a user opens the browser will display a web page server. My web server ip address is 10.10.1.5. [code]
View 4 Replies View RelatedI just installed a new RV042 v3 and updated the f/w to 4.0.3.03tm. While trying to sort out logging issues, I've tried a few times to restart the router via System Mgmt -> Restart -> Restart Router. When I do this I get the expected results -- I'm prompted to wait, and then to login again. But the System Up Time isn't reset to zero, and the log shows no sign of the router restarting.
Why doesn't this work? Is there some other way to remotely force a restart?
I try to join an ACS v. 5.3 to the domain. For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on the same location as the ACS ... this doesnt happen.
My question: How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?
i have a lan connection for internet, the wireless card is used for an adhoc connection to a device that does not have internet, my pc just keeps telling me i have no internet connection because it is letting the wireless connection take priority over the lan connection
View 2 Replies View RelatedIs there a way to force 40 mhz on a wmp600n. I have it connected to a e2000 router. When I bootup It connects at 130 mbps and if I let it sit for about a day or so it will eventually connect at 300 mpbs which is what I want it to connect at after boot. I dont see a option in the drivers for this adapter to force 40 over 20. Seems it connects at 20, then after so long it moves to 40.
View 2 Replies View RelatedI have a cisco router 881 with advipservices running ios Version 15.2(4)M1 this router is a device that the user will connect company equipement with antivirus and such.is there a way I can force the ports like fe0 fe1 2 3 to accept only devices with specific mac addresses?if not, is there a way for me to apply an acl to vlanX to block everything that's not from these specific addresses?
View 4 Replies View RelatedI'm trying to route all default traffic from my production environment through my ASA 5520 on the "outside2" interface.The 5520 has a site to site VPN to our DR site on the "outside/inside" interfaces via one ISP. On another ISP, interfaces "outside2/inside2" go to the internet.
When I make my 3750 stack default route for the inside2 interface IP I cannot get to the internet. When it is pointed to the inside interface on my 5505, I can.
I get the following errors when I try to open google.com from a production server:Why is the 5520 trying to use the "outside" interface instead of the "outside2" interface to go out?
I've configured the DHCP server on a Cisco Switch C3560E as follows:
ip dhcp excluded-address 172.16.0.1 172.16.10.255
ip dhcp pool perth_main
network 172.16.0.0 255.255.0.0
default-router 172.16.10.254
lease 0 8
!
My goal was to limit the dhcp to the range 172.16.11.0 - 172.16.13.255, as there are not so many user on this network I so limited the lease time to 8 hours in order to "recycle" the unused addresses". What happend is that it is always using new IPs, even if the lease time has expired.
IP address Client-ID/ Lease expiration Type
Hardware address/
User name
172.16.109.90 XXXXXXXXXXXX Apr 04 2013 10:00 PM Automatic
172.16.113.106 XXXXXXXXXXXX Apr 04 2013 06:55 PM Automatic
172.16.113.122 XXXXXXXXXXXX Apr 04 2013 09:04 PM Automatic
[code]....
1. How can I force the DHCP server to recycle the unused IPs?
2. Can I specify a DHCP range (172.16.11.0 - 172.16.13.255) instead of an "excluded-address" range?
What would happened if a force a cat4500-entservicesk9-mz.122-54.SG on a SUP-II-Plus+TS? Considering that:
- The same IP base file tha is used on a SUP-II-Plus+TS is used uma a SUP-V
- The file size os the ent services IOS is just a bit bigger the ip base IOS.
- Especially the EIGRP were supported on the SUP-II-Plus+TS pior the 12.2-25
We need full support to EIGRP(or OSPF) because of the H.A that are been implemented and need to test it...
I have just configured a ASA5505 running 8.2.2 as a webvpn server for clientless VPN connections.
I need to setup a particular bookmark for a RDP session which forces the use of the java client for those who can't seem to get the ActiveX control working for some reason or another (virus scanners/firewalls/scerutiy policies etc).
I created a bookmark as follows, but it always tries to connect with the ActiveX control first when logging on from an IE client.
rdp://192.168.1.1/?force_java=yes
I've set up a DHCP reservation on a Netgear wpn824v3 router, using its "Attached Devices" list to specify the MAC address of a computer on the network to use IP 192.168.5.200. After using "ipconfig /release" then "ipconfig /renew" on the client PC, though, the client PC keeps going back to the address it got automatically, i.e., 192.168.5.3.How can I force the client to use 192.168.5.200?
View 1 Replies View Related
