Linksys Wired Router :: BEFSR41v3 Enable UPnP / Password Not Accepted
Jun 30, 2007
I have a BEFSR41v3 and am trying to enable UPnP on the router. However, after I activate UPnP in my browser and the webpage reloads (after the common status screen that says you have to wait 5 seconds and you will be redirected). I am prompted for a password. But for some reason, it will not accept any password that I enter. In order to even get to the settings to UPnP in the first place, you must enter the correct password to access the settings. So I believe I am using the correct password, so why is it not accepting the correct password? I have had to reset my router to factory default settings (by pressing and holding the reset button for 30 seconds) multiple times because of this. But each time after enabling UPnP it will not accept the default password of admin nor will it accept any password that I assign it afterwards. I have noticed however that the "Filter Internal NAT Redirection" which should be set to enabled by default has been set to disabled even after I have reset the router. I have activated UPnP on the router before without trouble but have had to reset the router to factory default settings afterwards because of other reasons.
View 9 Replies
ADVERTISEMENT
Feb 11, 2011
I'm trying to stream music files to my A/V system. After weeks of encountering problems, I discovered that UPnP was disabled (by default) on the router. After enabling UPnP on the router, bingo......it worked. My A/V system has a Yamaha A/V receiver, which is a networking receiver capable of net radio and accessing/playing files on my PC. Net radio works fine. The problem I'm having is that when I shut down the A/V receiver, turn it back on, I can't access the files. I have to disable UPnP, save changes, and then reenable UPnP, save changes. When I do that, all is well and my receiver "sees" my PC and files. Shut down the receiver, turn it back on, back to square one and have to do the do the disable/enable routine again. PC is WinXP, using Windows Media Player 11. Seems the "enable" UPnP desn't "stick", even though it shows enabled on the setup page.
View 6 Replies
View Related
Feb 21, 2012
I posted a time ago here because i cant open my ports because i have a internet connection that first goes to my router and then to my modem [URL]
View 1 Replies
View Related
Feb 12, 2012
i Have a router called Linksys BEFSR41v3 i need to port forward a port but it just wont open i loggerd in on my router using 192.168.1.1 after i click applications & gaming started the port on 100 and ended on 100 used ipconfig in cmd to find me ipv4 adres and putted in ip adress box also both protocol are on and i clicked the enabled function also i tried also got a static ip i used canyouseeme.org to cheak if my port is open it still says its not open.
View 9 Replies
View Related
Nov 16, 2011
i cant open my ports because i have a internet connection that first goes to my router and then to my modem.
View 3 Replies
View Related
Nov 18, 2012
What are the steps I need to take to correct this so we can download books from amazon .Password on Kindle is not accepted by the Linksys router
View 2 Replies
View Related
Aug 11, 2007
I have a problem activating UPnP on my BEFSR41 V3 router. Whenever I try to activate it the 'admin' default administrator password no longer works. I have to reset the router in order to get back into the configuration web page. is there a version of the firmware which fixes this problem? I am currently at firmware level 1.05.00.
View 9 Replies
View Related
Oct 29, 2011
I have a Linksys router (model BEFSR41) and I all the outputs going to two computers and two gaming systems (X360 and PS3). I have had the router for over a year and it works fine, but I recently decided to attempt to have my 360 access the media on my computer by linking the two together through the Media Center. To do this, I needed to enable my router to allow UPnP (according to Microsoft help). When I did enable this, the router would disconnect me every 2-5 seconds from the internet, then would reconnect me right away.I have no clue why it was doing this (it occured across all of my devices) so I just disabled UPnP and things went back to normal. How to fix this so that I can have a consistent and stable connection when I have UPnP enabled?
View 1 Replies
View Related
Apr 19, 2009
BEFSR81 v3.0.I selecting Enabled UPnP and now I cannot access the router. When I enter the default admin for the password in the Authentication Required screen. I get the following screen: 401 Authorization RequiredThis server could not verify that you are authorized to access. Either you supplied the wrong credentials(e.g., bad password), or your browser doesn't understand how to supply the credentials required.I didn't enter anything new into the username or password fields.
View 5 Replies
View Related
Dec 20, 2011
I recently got a Motorola NVG510 (from AT&T, they changed our internet plan and sent a new router) and since then I've had problems with Skype. I think I've narrowed the problem down to there being no upnp on this router to enable, and Skype doesn't like that.So, is there any way I can make this option available, or some other way to 'simulate' upnp so Skype will play nice? I read somewhere else that "IP Passthrough" may be an option, but I'm unsure about that.
View 1 Replies
View Related
May 28, 2011
How to enable UPnP?
View 2 Replies
View Related
Dec 15, 2012
Trying to get internet on a very old PC. It's an old PC. But it's for an 8 year old. I just formatted the PC. Ethernet card was recognized. Not showing any issues in the device manager either. But when I choose my WN from the WNL and click connect, my password doesn't seem to work. It looks like it's connecting, but never does?
View 14 Replies
View Related
Dec 23, 2012
I have set up my first server. Its a HP N40L microserver & it works well but, after installing MythTV, when I try to run the backend I am asked for a password. I put in the admin password & it tells me the password is wrong. I have tried every password I can think of.
View 8 Replies
View Related
Dec 28, 2011
i currently usin mio router model 2701 HGV-E , may i knw does this model have UPNP function?? my com internet can go in , but when i try connect usin my ps3 , it said UPNP is not available. i use ps3 internet connection test all successed only the UPNP not available.
View 1 Replies
View Related
Oct 19, 2012
I have successfully installed ClearOS 6.3.0 at home and I need to enable UPNP for gamming, XBOX and Bittorrent.
View 1 Replies
View Related
Jan 6, 2013
I used to be able to connect to my internet with other computors but now it keeps saying we have the wrong password.
View 2 Replies
View Related
Jun 28, 2011
I bought this router (DIR-655) some time earlier this year, so it hasn't even been half a year that I've owned the thing. I set it up in the small duplex I was sharing with my sister and it worked quite well. Actually... for the first 45 minutes I was freaking out because I was getting practically no signal, then I realized I had forgotten to screw in the antennas... but that little anecdote aside, it worked fine.
I've since moved into a new place. I got a new modem, still on Videotron, I just upped the speed from 7 MB/sec to 15 MB/sec. Before setting up the router I inserted the CD that came with it and followed the instructions therein... things seemed fine, except that he automatically used the same network name that I used at my last place... almost like he was stuck on it. I couldn't figure out how to create a fresh new network. But I shrugged it off and continued, entering my own password and everything else.
Now, at the end he gave me 4 pieces of information,
A router password. A network name (SSID), this is the one who's name was stuck to the old one. A network security type, I went for Most secure(WPA) And the network security key, this was a randomly generated alphanumeric code of some sort.
I copied this in two different ways and the installation wizard automatically saved me a copy onto the desktop, so I know for certain I got the passwords right. I pulled out my iPad later, saw the network, a good strong signal, and tried to connect except it's not accepting my password. The password I triple-saved and checked without a shadow of a doubt. On a whim I tried to use the Security Key, and that seemed to connect for some reason, but it is considerably slower than it was at my last place.
The modem isn't to blame (it's running on double the speed now) and the signal strength is good. It's just that something gone weird with the password, and it feels very slow. Even if it wasn't slow, I would really like to know why none of my wifi devices are accepting the password I assigned.
And I used that http://192.168.0.1/ trick to look into the router settings from my computer. I changed the network password into something new. And still none of the devices will connect, they keep telling me it's the wrong password. I am only able to connect through the Security Key and I don't like that! I tried to contact D-Link's technical support the other day, but it drew on for so long my cellphone actually ran out of minutes.
Short Version: None of my wifi devices are accepting the password I gave during the setup and I don't know why!
I'm running a 64-bit Windows 7 on 1-year old dual-core desktop computer.
View 4 Replies
View Related
Jul 23, 2011
I got a D-Link router not too long ago and I set it up in an odd way, the router password I gave it during the setup would not be accepted but the Network Security Key (the randomly generated alphaneumeric code) was accepted. I used it to connect all of my wifi devices.
The router password (which doesn't work), the "network name (SSID)", the network security type, and the network security key were all saved on my desktop. My computer has since suffered a critical crash and had to have it's hard drive erased. I still remember the password, the network name, and the security type. But the NSK (the thing I need to connect in place of a password) has been lost. It was this long random string of letters and numbers that I couldn't remember for the life of me.
I also remembered my Admin password, so I am able to log into http://192.168.0.1, but in here I only know how to change the regular password. I don't know how to access or change the NSK. change the security setting so that I can use the actual password instead of the NSK? Because of the crash I lost my iTunes libraries so I'm going to have to reset all my iOS devices, which are primarily what I use wifi on. If I reset them, they'll forget the wifi network and the assosiated NSK password, so I won't be able to use wifi at all.
View 1 Replies
View Related
Feb 10, 2012
I can't find a way to enable UPnP or anything like it on my Motorola model 3360. I play online with my new xbox 360 and I have constant connection issues because it tells me my UPnP isn't enabled. I know my router isn't the problem because the problem continues even when my xbox is directly connected to the modem.
View 5 Replies
View Related
Feb 5, 2013
Trying to ssh from our QNAP to our switches and copy the running-config.These tests are on an SG-300. When ready well be doing the same thing on all of our 2960's. So maybe the SG300 is the problem.
View 1 Replies
View Related
Oct 20, 2012
How to enable UPNP on CISCO routers - 36XX , How can I simualte UPNP connections.
View 2 Replies
View Related
Mar 16, 2011
I have the setup disk and want to set up a password for the router. Don't want to mess things up since the system was installed by a pro. How do I simply enter a password to be used to connect?
View 3 Replies
View Related
Dec 21, 2012
I have just received this device from my deceased son-in-law and I need to know how to change the password. I do not know his and have no way of getting it.
View 2 Replies
View Related
Nov 14, 2010
BEFSR41 resets password to default by itself
View 9 Replies
View Related
Jun 24, 2012
My Dlink DIR-655 is hardware ver B1 and firmware 2.00. I found the UPNP cannot cross between wired and wireless network. It is fine if both UPnP server and renderor are on either network. There is no problem on other protocol, such as SAMBA from my notebook connected via Wireless to the QNAP NAS connected via Wired to the 655.
View 9 Replies
View Related
Apr 3, 2012
Last year our Network Security Supervisor submit his resignation and unfortunately did not endorse us the admin password we already tried the password he suggested when we contacted him but nothing of them works. Is there anyway we can reset the password without resetting to factory default?
View 1 Replies
View Related
Jan 24, 2013
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
View 1 Replies
View Related
Nov 26, 2011
I just set up the x2000 at my home Everything seems to be working fine. However, when trying to connect my play station 3. I get upnp not available when I run the internet connection test. With that, i am not able to connect to Modern Warfare 3 online. Haven't tried other games yet but i sign in to the play station network without any problems.
I have Upnp enabled on my router. I have tried port range forwarding and DMZ settings to my ps3. and still not working.
View 6 Replies
View Related
Feb 23, 2012
I have a wireless router and I'm trying to user UPnP feature. of course it is enble in the router.
It's working one and after it stop working, looks like the router is not responding anymore. If I got on the web interface of the router, I loging, on the first web page I press save changes, even if I didn't change anything, the UPnP feature work again.
Looks like a timeout occure or something like that. Is there a way to wake up the router without having to go on the web interface? Why it's stop working?
Firmware Version: v4.30.15
View 1 Replies
View Related
May 19, 2012
HAve UPnP enabled in the EA3500 but QNAP keep telling me "Your router does not support UPnP protocol or you have not enabled the UPnP function on the router"
View 8 Replies
View Related
Aug 31, 2010
So I just setup my new E3000, upgrading from a WRT54G. The uPnP worked great on that router and my last three routers before that. Xbox never required I setup anything -- I can prove this simply by swapping routers and putting one of the old ones in place of the E3000.However, the E3000 (Firmware Version: 1.0.02) is not working with uPnP. Xbox connectivity test comes back and says that my NAT type is "Moderate". Most stuff works fine, but I'd like to get it all working. I worked with a Linksys tech who got NAT to "Open" by configuring triggered port forwarding. I am happy to have my issue resolved, but confused why uPnP didn't work? I mean it was easy for me to configure port forwarding, but for my less technical friends, should I simply not recommend this router because it can't do basic uPnP?
View 2 Replies
View Related
Jul 31, 2012
I have a similar thread about this issue, the issue of this modem not support any kind of port forwarding actions... even disabling firewalls, using DMZ, port range forwarding the whole ip range , solves a thing...
it has upnp and port ranging features all over it but somehow it does not do it, and nobody cares excepty the ones that invested in it...
so if you are stuck with a router like me, dont bother wasting hours on it, and leave it to the people who are responsible for it.
View 2 Replies
View Related
Mar 9, 2012
I recently upgraded my linksys E1000 to: linksys E4200 ( i needed gb port)
In my QNAP I can scan for upnp routers to set the forwarding port automaticly.
But it keeps telling my, it can't find an upnp router on my network. My E1000 was found without any problem!
If I open the port manually for example FTP 21. I cannot get acces from the internet, it keeps telling me its closed.
I forwarded it to the right ip. an clicked to apply. The website from QNAP says the E4200 is certified for upnp
So tho sum up: I cannot acces my NAS from the internet.
My setup:
Modem/router (ZIGGO) --- Linksys E4200 ---- QNAP 412 turbo
Linksys E4200 firmware 10.04
View 9 Replies
View Related
