Linksys Wireless Router :: X2000 Upnp Not Available
Nov 26, 2011
I just set up the x2000 at my home Everything seems to be working fine. However, when trying to connect my play station 3. I get upnp not available when I run the internet connection test. With that, i am not able to connect to Modern Warfare 3 online. Haven't tried other games yet but i sign in to the play station network without any problems.
I have Upnp enabled on my router. I have tried port range forwarding and DMZ settings to my ps3. and still not working.
View 6 Replies
ADVERTISEMENT
Jan 24, 2013
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
View 1 Replies
View Related
Feb 23, 2012
I have a wireless router and I'm trying to user UPnP feature. of course it is enble in the router.
It's working one and after it stop working, looks like the router is not responding anymore. If I got on the web interface of the router, I loging, on the first web page I press save changes, even if I didn't change anything, the UPnP feature work again.
Looks like a timeout occure or something like that. Is there a way to wake up the router without having to go on the web interface? Why it's stop working?
Firmware Version: v4.30.15
View 1 Replies
View Related
May 19, 2012
HAve UPnP enabled in the EA3500 but QNAP keep telling me "Your router does not support UPnP protocol or you have not enabled the UPnP function on the router"
View 8 Replies
View Related
Aug 31, 2010
So I just setup my new E3000, upgrading from a WRT54G. The uPnP worked great on that router and my last three routers before that. Xbox never required I setup anything -- I can prove this simply by swapping routers and putting one of the old ones in place of the E3000.However, the E3000 (Firmware Version: 1.0.02) is not working with uPnP. Xbox connectivity test comes back and says that my NAT type is "Moderate". Most stuff works fine, but I'd like to get it all working. I worked with a Linksys tech who got NAT to "Open" by configuring triggered port forwarding. I am happy to have my issue resolved, but confused why uPnP didn't work? I mean it was easy for me to configure port forwarding, but for my less technical friends, should I simply not recommend this router because it can't do basic uPnP?
View 2 Replies
View Related
Jul 31, 2012
I have a similar thread about this issue, the issue of this modem not support any kind of port forwarding actions... even disabling firewalls, using DMZ, port range forwarding the whole ip range , solves a thing...
it has upnp and port ranging features all over it but somehow it does not do it, and nobody cares excepty the ones that invested in it...
so if you are stuck with a router like me, dont bother wasting hours on it, and leave it to the people who are responsible for it.
View 2 Replies
View Related
Mar 9, 2012
I recently upgraded my linksys E1000 to: linksys E4200 ( i needed gb port)
In my QNAP I can scan for upnp routers to set the forwarding port automaticly.
But it keeps telling my, it can't find an upnp router on my network. My E1000 was found without any problem!
If I open the port manually for example FTP 21. I cannot get acces from the internet, it keeps telling me its closed.
I forwarded it to the right ip. an clicked to apply. The website from QNAP says the E4200 is certified for upnp
So tho sum up: I cannot acces my NAS from the internet.
My setup:
Modem/router (ZIGGO) --- Linksys E4200 ---- QNAP 412 turbo
Linksys E4200 firmware 10.04
View 9 Replies
View Related
May 30, 2011
I have a Nat Strict problem with my router model WRT160N. I want to make a dedicated server with UT3.I tried many things like disabled all security in the router or disable UPNP, fowarding every ports that Unreal Tournament need or DMZ settings. I am running a batch file to start the dedicated server... but still have '' Nat is now strict'' in the log of my batch file. I cant see my server in the master server list inside the UT3 game. I tried to make the server without my router, directly connected to the modem and then it works instantly.
View 9 Replies
View Related
Dec 31, 2011
I cannot find the screen in the interface at 192. Where is this? Please don't say use Cisco Connect disc.
View 1 Replies
View Related
Jan 16, 2012
i am thinking of buying Linksys x2000 , WAG160N or any other you suggest to use as a wireless access point. Is it possible?My setup is : I get my internet from my neighbor by ethernet cable from his router. My house is two-storied and ethernet cable comes to top left corner of first floor and the devices(two notebook) are on the bottom right corner at the second floor , insulation greatly reduces the signal strength.
View 5 Replies
View Related
Feb 19, 2012
Is there support for album art or video thumbnails in the UPNP media server on the E3000? I've tried adding jpg files with the same name as the video file, but I see nothing in the client. I've also tried naming them 'folder.jpg' and 'cover.jpg' but still get nothing. If this isn't supported is there any plan to add support in the future?
View 2 Replies
View Related
Jun 19, 2012
My Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies
View Related
Sep 28, 2011
New firmware for the Linksys E4200 was released this morning that adds certification for DLNA, IPv6 Gold log, and UPnP. It also addresses the Media Server issues that have been identified here in the community.Sept 28, 2011Last Firmware version: 1.0.03 (build 14)- Added supports of Native IPv6 over PPPoE Internet connection when only keep alive option is selected.- Added supports of Native IPv6 on guest network if there are more than two available IPv6 subnets- Added supports of Native IPv6 on Parental Control- Added supports of 3TB Hard drive with NTFS and HFS+ format- Improved firmware upgrade stability- Improved IPv6 WAN performance- Fixed media server unstable issue- Fixed Cisco LED flashing issue- Fixed some minor bugs- DLNA certified- IPv6 Gold logo certified- UPnP certified
View 1 Replies
View Related
Jan 14, 2013
I did an upgrade to my firmware on the x2000 dsl router and now i cannot download apps with my android phone, i have tried everything that i can think of.
View 7 Replies
View Related
Nov 27, 2011
Just set-up a new X2000, loaded latest firmware 2.0.01, configured it via the web UI ('Browser based utility' as per the manual). Connected OK to my ADSL broadband by O2. Configured wireless, everything OK. Funny it doesn't need a user name, only a password, my prevoius WAG160N could be configured for both.Now I want to configure the Parental Controls, BUT apart from my computer name and an Android phone name, all I see in the Target Device ADD button pop-up are a list of repeated 'Network Device'. There seems no way to be able to distinguish which is which device (mix of XP & Win 7 PC's and HP Printer through a separate switch), as it does not show IP address or MAC.
I thought I may have better luck with the Cisco Connect software (which I didn't use to set-up the router). I downloaded the latest version 1.4.11194.0, and ran this on another computer with wireless. Apart from reconfiguring my static IP address to DHCP, and then connecting through DHCP, the software said it could not configure my router. So it never gets to a point where it installs any program on the computer so that I can configure Parental Controls. How do I get the router to show ALL the computer names in the list rather than 'Network Device' or is there a way to distinguish which 'Network Device' is which computer?
View 2 Replies
View Related
Nov 10, 2012
I have a linksys x2000 modem router.According to this page it have wireless N and 300Mbps url...i check al off options but..and i'm not satisfied it's antenna coverage (same as cheap modem! )
View 6 Replies
View Related
Aug 11, 2007
I have a problem activating UPnP on my BEFSR41 V3 router. Whenever I try to activate it the 'admin' default administrator password no longer works. I have to reset the router in order to get back into the configuration web page. is there a version of the firmware which fixes this problem? I am currently at firmware level 1.05.00.
View 9 Replies
View Related
Feb 11, 2011
I'm trying to stream music files to my A/V system. After weeks of encountering problems, I discovered that UPnP was disabled (by default) on the router. After enabling UPnP on the router, bingo......it worked. My A/V system has a Yamaha A/V receiver, which is a networking receiver capable of net radio and accessing/playing files on my PC. Net radio works fine. The problem I'm having is that when I shut down the A/V receiver, turn it back on, I can't access the files. I have to disable UPnP, save changes, and then reenable UPnP, save changes. When I do that, all is well and my receiver "sees" my PC and files. Shut down the receiver, turn it back on, back to square one and have to do the do the disable/enable routine again. PC is WinXP, using Windows Media Player 11. Seems the "enable" UPnP desn't "stick", even though it shows enabled on the setup page.
View 6 Replies
View Related
Apr 19, 2009
BEFSR81 v3.0.I selecting Enabled UPnP and now I cannot access the router. When I enter the default admin for the password in the Authentication Required screen. I get the following screen: 401 Authorization RequiredThis server could not verify that you are authorized to access. Either you supplied the wrong credentials(e.g., bad password), or your browser doesn't understand how to supply the credentials required.I didn't enter anything new into the username or password fields.
View 5 Replies
View Related
Jun 30, 2007
I have a BEFSR41v3 and am trying to enable UPnP on the router. However, after I activate UPnP in my browser and the webpage reloads (after the common status screen that says you have to wait 5 seconds and you will be redirected). I am prompted for a password. But for some reason, it will not accept any password that I enter. In order to even get to the settings to UPnP in the first place, you must enter the correct password to access the settings. So I believe I am using the correct password, so why is it not accepting the correct password? I have had to reset my router to factory default settings (by pressing and holding the reset button for 30 seconds) multiple times because of this. But each time after enabling UPnP it will not accept the default password of admin nor will it accept any password that I assign it afterwards. I have noticed however that the "Filter Internal NAT Redirection" which should be set to enabled by default has been set to disabled even after I have reset the router. I have activated UPnP on the router before without trouble but have had to reset the router to factory default settings afterwards because of other reasons.
View 9 Replies
View Related
Oct 29, 2011
I have a Linksys router (model BEFSR41) and I all the outputs going to two computers and two gaming systems (X360 and PS3). I have had the router for over a year and it works fine, but I recently decided to attempt to have my 360 access the media on my computer by linking the two together through the Media Center. To do this, I needed to enable my router to allow UPnP (according to Microsoft help). When I did enable this, the router would disconnect me every 2-5 seconds from the internet, then would reconnect me right away.I have no clue why it was doing this (it occured across all of my devices) so I just disabled UPnP and things went back to normal. How to fix this so that I can have a consistent and stable connection when I have UPnP enabled?
View 1 Replies
View Related
Jun 4, 2012
I've never setup a router before, but when I tried to setup this one it required me to put in the isp ip, subnet, gateway, and dns. I assumed that this was not my ip but the ip of zoomtown which when i looked at the old routers info i figured this was the ip under the configurations summary that said wan ip, perhpaps i was wrong, i'm not sure but this ip info is static it does not change , but I believe the individual computers ip addresses use dhcp and are not static.
View 3 Replies
View Related
Apr 27, 2013
Is it possible somehow to use Unicode symbols on X2000 wi-fi+adsl router?
View 2 Replies
View Related
Jan 7, 2012
I would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies
View Related
May 26, 2012
I have a Linksys X2000 modem. Why does my internet go down several times a day? My provider is Century Link and I have already called them. They say all is well on their end, so it must be my modem. I reset and sometimes it pops right back and other times it takes an hour or more.
View 2 Replies
View Related
Jul 15, 2012
I recently installed a Cisco X2000. Several PCs running Windows XP Pro connect wirelessly. Also, we have an Android device and iPhone connected to the wireless network. We have a network printer and network drive connected via wires to the router. Most of the time the router and cable modem features work well. However, every so often all devices lose wireless signal simultaneously. It is not possible to reconnect to the X2000 unless I unplug the X2000 and plug it back in. After this reboot, we can connect again. Obviously, this is quite frustrating. By the way, we get acceptable signal strength after the X2000 locks out however none of the devices (computers or phones) are able to connect.
View 1 Replies
View Related
Nov 14, 2011
How well Cisco Linksys x2000 router/modem works with at&t high speed internet speed?
View 4 Replies
View Related
Aug 18, 2010
I try to start with UPNP in my LAN network. Everyting works if I use Wifi connection but does not for wire connections. All tests suggest that router block UPNP traffic. Of course my WAG 200G in managment menu is for UPNP enabled. ex. downgrade firmware or something like this?
View 2 Replies
View Related
Nov 22, 2012
How can i add several vpi / vci to my Linksys x2000 ?
View 7 Replies
View Related
Dec 1, 2012
Just picked up a X2000 and Cisco connect configured my connection, and assigned an IP to my desktop pc.I configured my PC back to a Static IP which is outside the DHCP range in the X2000, and all seems to be working ok..now looking in the web-based X2000 setup screen my pc is no longer listed as a client...so should I manually add it as a client and assign the IP & MAC address in the Cisco setup or is this not necesary.?
View 5 Replies
View Related
Jul 4, 2012
I have the X2000. It has 3 ports. I need 4. I also have the WRT160N V3 router which has 4 ports. Is there a way to use this router with the X2000 to get the 4 ports I need ? If not, what are my other options to get 4 ports ?
View 2 Replies
View Related
Nov 3, 2011
I've tried everything to get this to produce an i.p address but to no avail.I check with my ISP (o2/BE) they told me all my settings are correct it syncs but just does not pick up an IP address.
View 6 Replies
View Related
Jun 27, 2012
linksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work
View 3 Replies
View Related
