I have DIR600 Rev. B1 for about 2 years, and it's been working without a problem.Suddenly yesterday, I could not connect to the internet from my 2 laptop & blackberry.SSID & signal reception looks normal. On checking into the router's web interface, I noticed that the network key was changed into something else.....normal character like y2tz39s.
I'm being very curious. Has it been hacked ? Is it possible?I'm using WAP/WAP2 Security Setting for wireless connection.All other settings seems intact (firewall & even the SSID). Only the password was mysteriously changed. If I consider it being hacked, I wonder why the hacker didn't mess up all other settings ?
i tried using the internet on my ipod but my wifii network wasnt connected so i went to my wifi settings on my ipod and the network name and password were changed. i tried resetting my router but nothing happened and i still cant get wifi on my ipod.
Changed from D-Link to Netgear router now only one of two computers cannot see the other. Error shows cannot connect to MSHOME network, need administrative approval. Computers are ethernet connected to the router. Have McAffe and both computers are "Trusted" Can do a search with XP and it shows the missing computer but unable to make a connection.
My mother accidentally turned off wireless or changed the password to the 2WIRE778 that we have and I can't get wifi on my iPod. So I have a small motorola router and it's wireless so if I hook it up to the original 2WIRE that has blocked wifi do you think I can get wifi off the second router with no password troubles or would I have to buy a special router that has no password? I don't know a lot about computers. And my Meyer has a password on our computer so I can't log on. so if I just hook up the 2nd router and possibly get WiFi do I need to do anything such as setup on the computer or can I plug it in and just go?
Today I wanted to change my passwords on my router Cisco 888e.I connect by telnet my router and access the enable mode.Then, I set my enable password to passwordxxx with the command enable password password1.After a show run, i could see in this config my new password correctly set. Then, I set my enable secret password to passwordxxx (the same) with the command enable secret password password1.I log off the enable mode.Try to log on with the command en but when I type the new or the old password, I receive a 'Access denied' message.
And I'm sure of the new one because on my command line to define it I could see this new password in clear!What are my solutions to access the enable mode again?If I reboot my router, it'll run the previous config file with the old password? I've only worked on the running config file and haven't apply these changes to the nvram.
My son decided to update our router firmware, together with this the password was changed. My computer which hosts the Internet connection works fine, all other laptops have now been connected successfully after simply changing the password. However my wifes laptop won't play ball. It is a Samsung R510, with Vista Home Premium OS. It worked fine prior to updating the firmware. I have been through the process of changing the password and have the correct security encryption in place, exactly the same process as with the other laptops.
It then says successfully connected, but shows in the bottom right of the screen, Unidentified network access local only and will not connect when the browser is opened. I have tried to diagnose but the usual windows prompt to reboot both modem and router has no effect. I have set it to private, as advised elsewhere, I have switched the firewall off and removed security software, all to no avail.
I tried the command prompt, then ipconfig/renew. An error occurred while renewing interface Wireless Connection: unable to contact your DHCP server. Request has timed out. No operation can be performed on Local Area Connection while it has media disconnected. Let me stress that no changes were made to the laptop at all, it is simply not connecting following the firmware update and password change. All other computers, and phones, 6 in total, are all working fine from simply changing the password.
I returned to work and found a note that my Outlook and Windows password had been changed during the night by the IT department. Why would they need to change my password? Are they monitoring my work somehow.
Changed my AD password and now i cannot get into the enable side of the cisco switches on our network (we have no routers).Looking on the logs for the ACS v4.2 I can see the following -
On TACACS+ Accounting you can see the connections which have worked - it the initial tty connections -
When i look in the failed attempts i see the following Auth failed - External DB user invalid or bad password or on another occasion internal error or EAP-TLS or PEAP authentication failed due to unknown CAcertificate during SSL handshake.
Whenever I load a gallery of images or even when I open up a couple of websites, sometimes the image/website won't load and is perpetually loading, only to time out minutes later.I've tried out different browsers (Chrome, Firefox) on my wired desktop and tried this on my Laptop through WiFi with the same two browsers. The result was the same each time. So it's not about faulty computer hardware, software or malware on the machines. [code] When I ran a Speedtest.net test, this weird issue happened on the end-result screen. Normally when you do a test there, you can share/compare etc. But for me, that content did not appear.On Reddit I browsed a couple of ragecomics for my leisure and then some of the img.ur hosted images won't load. I know this issue still exists, because I use Randomly ordered wallpapers / Wallbase.cc to test out the case. By using this link, you're presented with a bunch of random thumbnails. So I scroll down and keep loading thumbnails as fast the website and I can endure. But at one point, it will stop at a random thumbnail, load the first 20% of the image and freeze. Or it will load 20%, freeze, and continue loading the rest. I also tried this out by opening wallpapers, closing them with CTRL+W, repeating this process until one of them refused to load, but when I refreshed the browser it would magically load the image.
I have reset my modem and my router, the router has been restored to factory defaults. So I'm clueless on what could be the cause of this weird issue. Nothing in the LAN has changed, this started about a week ago. I've narrowed it down to the router, but there's nothing in the settings that would cause this behaviour.
I have a Linksys E3000, have had it successfully connected for three months now. Recently I attempted to connect my xbox 360 to the wifi and had issues connecting it. So I called ATT to obtain the PPPoE username and password, which they reluctantly gave me. Entered that into the xbox and still unable to connect, so I have given up on the xbox for the time being, I'll post that issue in a different forum. Where my issue is now is since contacting ATT the WPA2 password I set up for the router no longer works. I cannot access the router setup page, and I cannot add any new wifi devices. Although, all of the previously connected wifi devices are still connected to the router despite this issue. Is there anyway to make the old password work, or do I have to reset the router and start from scratch, and God forbid contact ATT again?
Recently, I bought the E3200, and tried to configure its ports for gaming. Yet, whenever I would hit save settings, it would say my settings were saved, then return me to the settings page. But the settings would be blank. I tried downloading firmware from the website (which should say September 28), yet it still says I am running the firmware from September 1st, even after I applied the upgrade and followed through with the 50 second reboot process.
So, I guess my final question for any tech savvy person out there is "What is wrong with my router/firmware?" I am running the browser config in the most recent Firefox on the same MacBook I used to install the router, and haven't changed any settings other than the SSID and password.
i have 7 AP's in a school...i have numbered them 1 to 7 and have a strong password on im being called out every few months to reset the AP as its not working when i get there i see the ssid has changed to hp-josh1a seems like a computer name (its different most times) how are they changing the ssid of the tp link?
I had something odd happen to my Dlink router DIR-651 model. During the early evening hours someone changed the SSID name of my Router. Nothing else changed that I could see right off. So I reset the router to Factory Defaults.
DIR655 with 1.33NA firmware. I'm trying to determine how to block access to the internet for a specific LAN computer when the user knows how to change a MAC address. I don't want to turn MAC control on and grant only to listed computers - the list doesn't accommodate enough MAC addresses, and the client has wireless and wired since it's a laptop. I also don't want to set static IPs on all of the devices since some cannot accommodate that feature.I'm thinking that reserving an IP address isn't ultimately the solution either, since assigning the IP isn't going to work if the MAC changes. how to use access control under these circumstances?
Laptop, Desktop with USB stick, and 2 notebooks all were working fine on wireless prior to switching from phone line, to high speed cable connection at router. Have tried reset, unplug power, reinstalled router and everything else I could think of but none of them will connect. Shows a good strong signal from router but will not connect. Re-entered numbers, password etc as well in all other computers. What else to try other than a new router? Could it be coincidence that router decided to quit, around same time as changeover? Cable connections good and main computer connected via cable works ok, just all wireless not working.
Can't log in to d-link either. wrong password,? Type in admin, but won't log on without password and I tried but won't accept . Hitting reset and then retry didn't work either?
We've been using a 2Wire from our ISP to connect to the internet, and a Dlink DIR 655 for our wireless network. (Since the 655 has "N" speed, we can transfer large files between computers much faster than with the 2Wire.) The setup has worked fine for a few years, but recently both devices were slow. After turning them off and on a few times, unplugging, etc., without much effect, I reset both units. They're working now, but I've lost our network name and password; our Macs (and iPhone & iPad) are now using the default unlocked Dlink network. I tried to input the Dlink's default IP address, 192.168.0.1, but the address never connects. Any suggestions on how I can access our DIR 655's IP address, so I can reinstall a password and network name? If our tech guy (now unavailable) changed the Dlink's default IP address years ago, wouldn't it it have reverted to the 192.168.0.1 when I reset?
Received a replacement DCS-930L today; using WPS, did setup wirelessly; all OK. Then did firmware update wirelessly (with second, DCS-932L, turned OFF). The v1.03 firmware file was the same one I previously used, I think. Amazingly, The camera menus are now in French, and I can't find a setting to change it to English.
With basic "Wizard" setup I got DHCP and port 80 for the camera. It was working just fine with MyDLink and locally with DLink-ViewCam software and some local test web pages. However, we have a wireless printer on that router which also uses port 80, so when it was installed we set up a "port forward" for port 80 traffic to it for administration from other subnets. How MyDLink website is able to tunnel through our hardware firewall and the wireless routers firewall to communicate with the camera is not clear to me (perhaps someone can send me a link to an explanation??), but it works...Thus, to allow access to the camera from other subents, I wanted to change the camera's port from 80 to another, say 8181 and set up the appropriate "port forwarding for TCP and UDP. All of the steps below were from a PC within the camera's subnet/router so port forwarding is not an issue
Had to reset out DIR-655 router. This ended up changing our network password. Unfortunately, my DAP-1522 was not informed of this change and it will not connect to my Directv receiver now. I attempted to log into the bridge to change the password and it will not let me in. I attempted to reset the DAP in hopes that I would just be able to start over from scratch, but no dice (Assuming that I did it correctly)
I will try to explain my problem as clear as possible but my knowledge about networks and routers is very limited.
I have a DIR-615 version:C1 firmware:3.13NA My ISP is ATT DSL Modem is Siemens SpeedStream 4100, it does not have a router built in Internet line is connected from wall to modem, to router, to PC.
after I upgraded the firmware I had no internet coming out of the router, I bypassed the router and connected straight to the PC and I got internet. I unplugged the power on both modem and router waited a whole night (I was too tired) and in the morning internet was back to PC and I had WIFI again BUT. When I put a password on the WIFI network all my stuff finds the signal but cannot connect, if I open the signal meaning if I have no password and the WIFI is open I can connect all of my electronics without any problems.
I already tried using WEP and WPA but still unable to connect anything, I been leaving my signal open when I'm at home for the last week and I don't like it.
Before the update everything worked fine.
I don't know if this matters but I have a PS3, Wii, Roku box, Laptop and a couple cell phones connected to it. And there are like 6 or 7 network signals close to my house.
Since I changed the password on my wireless router{linksys}, my desktop is fine but both laptops cannot find network connection. when I ipconfig/all I get "media disconnected" and no ip address.
I got a D-Link router not too long ago and I set it up in an odd way, the router password I gave it during the setup would not be accepted but the Network Security Key (the randomly generated alphaneumeric code) was accepted. I used it to connect all of my wifi devices.
The router password (which doesn't work), the "network name (SSID)", the network security type, and the network security key were all saved on my desktop. My computer has since suffered a critical crash and had to have it's hard drive erased. I still remember the password, the network name, and the security type. But the NSK (the thing I need to connect in place of a password) has been lost. It was this long random string of letters and numbers that I couldn't remember for the life of me.
I also remembered my Admin password, so I am able to log into http://192.168.0.1, but in here I only know how to change the regular password. I don't know how to access or change the NSK. change the security setting so that I can use the actual password instead of the NSK? Because of the crash I lost my iTunes libraries so I'm going to have to reset all my iOS devices, which are primarily what I use wifi on. If I reset them, they'll forget the wifi network and the assosiated NSK password, so I won't be able to use wifi at all.
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password newpassword confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
I used to play online games with GameSpy. Suddenly, GameSpy Arcade just won't connect anymore, and i also noticed that almost everything related to GameSpy is blocked in my entire network. The only GameSpy site i can connect is gamespy.com, but GameSpy forums and gamespyarcade.com are blocked. I haven't changed any network settings, and i've tried to connect without firewall and without avast antivirus, but it just won't work. The only way i can get to those sites is through a proxy, i think that means that THEY are blocking me, and not my own network, right?
I am making my wireless network with Wireless router DIR-600 and DWA-525 desktop adapters for my office. I created a most secured type of network WPA2. And I have to create profile for DWA-525 desktop adapter to connect to my network and it requires the network secret key to connect. But This secret key is viewable from the "Network connection manager" when one can click on modify network and click on "Show text in the password field" by everyone using this computer (I mean by all other office staff). I don't want to let any one know my wireless network secret key. Is there any way to protect the key while having the computers automatically connected to wireless network. More information is below
Model: DWA-525 Hardware Version: A1 Firmware Version: 1.10 Operating System: Windows 7 Service Pack: 1
We have two networks in our lan: 10.0.0.0/24 and 192.168.1.0/24. Actually the networks are separated. The 192.168.1.0/24 network contains some hosts that ip can not be changed. We want redesign the network and communicate with both networks without routers. I thougnt about changing the netmask for 192.168.1.0/24 in 192.168.1.0/22 (1022 hosts) and change IP's in the 10.0.0.0/24 network in 192.168.2.0/22.
my daughter connected her laptop to my in-laws Linksys wireless connection which did not require a password. Now the Network has been renamed SQUEEZER-PC_Network (SQUEEZER-PC is the name of my daughter's laptop)and it requires a password.
I have been trying to connect a camera to the wifi router at my mother's assisted living facility. The password has a special character, "!".
After hours waiting on the phone with tech support, they confirmed that only letters and numbers are supported. Guess i have to take it back.
Incidentally, the software is changing "!" to "%21", which is the escape sequence used in URL's. The camera software isn't mapping it back. Should be fixable in firmware.
Region : Australia Model : TL-WR1043ND Hardware Version : v1 Firmware Version : 3.13.12 Build 120405 Rel.33996n
I just upgraded from my factory default and found network sharing of my USB HDD was no longer working.It came down to two bugs in the latest firmware:Even though there is now the option to share without a password that option does not work and you still need a password.And that password is the factory default of "admin" even though I have set my own password.
The company I work for has a small network and it has a windows 2000 server. When the Canon iRC 2880 printer is connected the server gives a error saying that a duplicate name exits in the network. I tried changing the IP address as well. When I changed the IP address of the printer the duplicate IP address moved the new IP address.
I have a wrt160n router set up at a friends house that i would connect my windows xp laptor to when i would go there. it always worked fine. i recently got a new laptop with vista 64 bit OS. i went to my friends today and connected via wireless for the first time. i expected to get prompted for the security key. instead it asked for the pin #. the pin number was something new i noticed when i replaced an older linksys with the new wrt160n so i had it in my notes. i entered the pin number and connected to the wireless router. but then my friend laptop could not connect and said it couldnt find the network. when i viewed the available networks, i noticed that the original network SSID had been changed to my vista laptop's computer name. i had to physically connect my laptop to the router and reconfigure the settings of the wireless network. then my friend was able to see the available network and automatically connect..
