D-Link DIR-615 :: Unable To Password Protect Network?
Feb 28, 2011
I will try to explain my problem as clear as possible but my knowledge about networks and routers is very limited.
I have a DIR-615 version:C1 firmware:3.13NA My ISP is ATT DSL Modem is Siemens SpeedStream 4100, it does not have a router built in Internet line is connected from wall to modem, to router, to PC.
after I upgraded the firmware I had no internet coming out of the router, I bypassed the router and connected straight to the PC and I got internet. I unplugged the power on both modem and router waited a whole night (I was too tired) and in the morning internet was back to PC and I had WIFI again BUT. When I put a password on the WIFI network all my stuff finds the signal but cannot connect, if I open the signal meaning if I have no password and the WIFI is open I can connect all of my electronics without any problems.
I already tried using WEP and WPA but still unable to connect anything, I been leaving my signal open when I'm at home for the last week and I don't like it.
Before the update everything worked fine.
I don't know if this matters but I have a PS3, Wii, Roku box, Laptop and a couple cell phones connected to it. And there are like 6 or 7 network signals close to my house.
View 1 Replies
ADVERTISEMENT
Oct 30, 2011
I am making my wireless network with Wireless router DIR-600 and DWA-525 desktop adapters for my office. I created a most secured type of network WPA2. And I have to create profile for DWA-525 desktop adapter to connect to my network and it requires the network secret key to connect. But This secret key is viewable from the "Network connection manager" when one can click on modify network and click on "Show text in the password field" by everyone using this computer (I mean by all other office staff). I don't want to let any one know my wireless network secret key. Is there any way to protect the key while having the computers automatically connected to wireless network. More information is below
Model: DWA-525
Hardware Version: A1
Firmware Version: 1.10
Operating System: Windows 7
Service Pack: 1
View 1 Replies
View Related
Jan 5, 2013
I use to be running on firmware 1.0.2.4 with ProtectLink-Web working great, but then it expired. Some time later I updated the router to 1.0.4.17 and purchased a three year subscription to ProtectLink-Web, followed the registration link on the router, obtained an activation code, followed the activation link on the router and activated the service, however it didn't activate on the router.
I try to activate again and Trend Micro's site just says that it's already been activated. I contacted Trend Micro support and they see the activation attempts on there end and they said everything should be working. They recommended a factory reset which I performed and then attempted activation again, and again their site says that the service has already been activated. And yet when I go to Cisco ProtectLink Web > License > Summary it just says: "Please activate ProtectLink License to display the license information" and wont allow me to access the features. What is going on? Could the firewall be blocking the service? I didn't have this trouble the first time I used ProtectLink with f/w 1.0.2.4
View 2 Replies
View Related
Aug 19, 2012
How do I password protect my linksys router?
View 2 Replies
View Related
Jun 2, 2011
Right now mine isn't PW protected, but I think I'm going to do that. Anyway, my question is, if I change my router settings and make it PW protected will I have to type that in every time I turn on my computer to get access to the internet?
View 7 Replies
View Related
Jun 8, 2012
I have an asus wireless router the router lost connection for a few days and when Internet came back there was no password to protect Internet and was just basically open access. The computer which all the Internet setting are on went away for repair. When the man brought it back after backing up the computer I asked him to put the password back on the Internet. This he has done. We entered the new passwords on our iPhones and they connected and worked no problem. Then we tried to do it with our laptops but they won't connect. Phoned the bloke back he said we had to get the laptops to forget all the old settings for the router and it would on take five minutes but he never told us how to do it.
View 1 Replies
View Related
Sep 23, 2011
I am trying to password protect my router but when I go into wireless> security mode and click on WPA or any of the other choices it goes back to disabled.
View 3 Replies
View Related
Oct 28, 2007
My router has been in use for some time. WRT54G. I did the set up from the disc and instructions and it's been no problems. I would now like to add a password to log on to it from a wireless computer such as my laptop or the other household computer.
View 9 Replies
View Related
May 16, 2011
I have a Netgear router which feeds an Eugenius ecb3500 Wireless Access point. I did not install the access point. I need to password protect our wireless environment, and that needs to be done on the Engenius. However, though I have tried many ways to access that device, I cannot. I cannot get an IP address for it,either. When I plug it directly in to my laptop (Win7), and type in the command line ipconfig, I get the IPv4 addresses of my laptop's local and wireless LAN card. How to get into the Engenius access point and password protect it?
View 1 Replies
View Related
Feb 6, 2008
I have a linksys WRT54G router. I am able to get to the admin menu via IP 192.168.1.1 but can not figure out where to to navigate to or how to put a (password on the wireless access) so my neighbors wont be able to use my router to get on the internet.
View 5 Replies
View Related
Jul 6, 2012
Hardware version: A4, Firmware version: 1.35NA.
The device is working just fine but I just want to change the password but it failed. I opened my web browser enter 192.168.0.1 then logged into the admin account then put in the new password for both admin and user, clicked save setting...it asked for rebooting the device I let it rebooting. Everything went fine. I was able to log in both the admin and user acc with the new password. The only problem is that my PC can still connect to the network using the old password? I expect that the PC will need to use the new password to access the network but this is not the case.
View 8 Replies
View Related
Sep 13, 2011
I went through the install procedure outlined in the ProtectLink Gateway install manual and i activated the ProtectLink Web product through Trend Micro (which shows up through their web site as a registered product to me). It still doesn't show up as installed on the SA540 (under Administration/License Management screen). When I try to activate the product again, it shows as "Already registered". Trend has no idea why it won't work. They said Cisco sold the license, so try their support.
View 1 Replies
View Related
Oct 7, 2011
I have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button.
My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).
View 1 Replies
View Related
Jan 27, 2013
Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 2.1
ISP : PTCL
trying to connect to router configuration (after several factory resets) at 192.168.0.1 but each time screen displays invalid username / password,doesnot even display username / password window,using admin as username and password,just cannot log on to configuration setup
View 3 Replies
View Related
Aug 9, 2011
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
View 4 Replies
View Related
Jul 30, 2011
My proplem is about my home network. There is computers on my home network can access to my files!How can i protect my files from them
View 2 Replies
View Related
Nov 29, 2011
We are a non-profit organization that is heavily reliant on interns that use their own laptops a lot here. My concern is they come in and connect to our wireless network with no supervision or anything else. I am worried they will introduce a virus, trojan, or something to our network. What the best way to keep them from introducing unwanted malware from a thumb drive, virus in email, or something to that effect shy of standing over them while they install and run an antivirus software?
View 7 Replies
View Related
Dec 29, 2011
how can we see who are connected to our wireless network and as in some types wireless key can be see or hacked, how can we stop or prevent this.
View 1 Replies
View Related
Oct 5, 2012
I am not able to connect to password protected network while others get connected to the network and are using it.even if it gets connected it shows no internet access. I tried troubleshooting and it said no valid ip configuration.
View 10 Replies
View Related
Nov 21, 2012
We've been using a 2Wire from our ISP to connect to the internet, and a Dlink DIR 655 for our wireless network. (Since the 655 has "N" speed, we can transfer large files between computers much faster than with the 2Wire.) The setup has worked fine for a few years, but recently both devices were slow. After turning them off and on a few times, unplugging, etc., without much effect, I reset both units. They're working now, but I've lost our network name and password; our Macs (and iPhone & iPad) are now using the default unlocked Dlink network. I tried to input the Dlink's default IP address, 192.168.0.1, but the address never connects. Any suggestions on how I can access our DIR 655's IP address, so I can reinstall a password and network name? If our tech guy (now unavailable) changed the Dlink's default IP address years ago, wouldn't it it have reverted to the 192.168.0.1 when I reset?
View 4 Replies
View Related
Dec 29, 2011
Had to reset out DIR-655 router. This ended up changing our network password. Unfortunately, my DAP-1522 was not informed of this change and it will not connect to my Directv receiver now. I attempted to log into the bridge to change the password and it will not let me in. I attempted to reset the DAP in hopes that I would just be able to start over from scratch, but no dice (Assuming that I did it correctly)
View 4 Replies
View Related
Dec 13, 2012
I have DIR600 Rev. B1 for about 2 years, and it's been working without a problem.Suddenly yesterday, I could not connect to the internet from my 2 laptop & blackberry.SSID & signal reception looks normal. On checking into the router's web interface, I noticed that the network key was changed into something else.....normal character like y2tz39s.
I'm being very curious. Has it been hacked ? Is it possible?I'm using WAP/WAP2 Security Setting for wireless connection.All other settings seems intact (firewall & even the SSID). Only the password was mysteriously changed. If I consider it being hacked, I wonder why the hacker didn't mess up all other settings ?
View 1 Replies
View Related
Jul 23, 2011
I got a D-Link router not too long ago and I set it up in an odd way, the router password I gave it during the setup would not be accepted but the Network Security Key (the randomly generated alphaneumeric code) was accepted. I used it to connect all of my wifi devices.
The router password (which doesn't work), the "network name (SSID)", the network security type, and the network security key were all saved on my desktop. My computer has since suffered a critical crash and had to have it's hard drive erased. I still remember the password, the network name, and the security type. But the NSK (the thing I need to connect in place of a password) has been lost. It was this long random string of letters and numbers that I couldn't remember for the life of me.
I also remembered my Admin password, so I am able to log into http://192.168.0.1, but in here I only know how to change the regular password. I don't know how to access or change the NSK. change the security setting so that I can use the actual password instead of the NSK? Because of the crash I lost my iTunes libraries so I'm going to have to reset all my iOS devices, which are primarily what I use wifi on. If I reset them, they'll forget the wifi network and the assosiated NSK password, so I won't be able to use wifi at all.
View 1 Replies
View Related
May 16, 2010
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password
newpassword
confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
View 4 Replies
View Related
Dec 1, 2012
I have been trying to connect a camera to the wifi router at my mother's assisted living facility. The password has a special character, "!".
After hours waiting on the phone with tech support, they confirmed that only letters and numbers are supported. Guess i have to take it back.
Incidentally, the software is changing "!" to "%21", which is the escape sequence used in URL's. The camera software isn't mapping it back. Should be fixable in firmware.
View 6 Replies
View Related
Nov 12, 2012
Region : Australia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
I just upgraded from my factory default and found network sharing of my USB HDD was no longer working.It came down to two bugs in the latest firmware:Even though there is now the option to share without a password that option does not work and you still need a password.And that password is the factory default of "admin" even though I have set my own password.
View 1 Replies
View Related
Sep 30, 2011
I recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies
View Related
Feb 25, 2012
Unable to use AirPlay on a D-Link network. Disable WMM in the Advanced->Advanced Wireless tab.I struggled for weeks with this. AirPlay worked fine on an all Apple network but when I switched to the DIR-655 as the router/ap AirPlay became invisible. I could see the Airport Express in the list of connected devices with an IP address but the AirPort utility and AirPlay enabled apps were unable to see it. Disabling WMM fixed it immediately and I am now back to streaming music.
View 14 Replies
View Related
May 26, 2011
I am having linking a computer to our SBS server. The computer in question is set in a warehouse on our site. We have a leased internet connection which is used on a number of different offices. The sbs-server has an IP address of 192.168.50.254 with a gateway Ip address of 192.168.50.1. The firewall on this network has an external IP of 10.50.0.37 with a gateway of 10.50.0.254 and this links to the leased line equipment. The external IP address for this network is 62.7.70.237. The PC in the warehouse has an IP address of 192.168.0.2 attached via a router to the leased line. The routers Ip address is 192.168.0.1, the external IP address is 10.50.0.55 and a gateway of 10.50.0.254. This links to the leased line and seems to have an external Ip address of 62.7.70.238. My issue is that I want the PC in the warehouse to be able to connect in some way to the SBS-Server. I cannot seem to access it via the external IP or the gateway (10.50.0.37).
View 2 Replies
View Related
Mar 6, 2013
I recently purchased a DIR-815 D-Link router. I've set up my network successfully; my laptop and smart phone are easily able to connect. However my desktop is having issues. My network card detects the wireless network I have set up, however the password is always rejected. I am typing in the correct password. I can get the internet to work on my desktop if I connect the router directly by wire, but I need the wireless to work. My desktop runs Windows 7.
View 3 Replies
View Related
Jun 17, 2010
I recently bought 3 DCS-920 to monitor my home while at the office. However I can't seem to get the damned things to stream video using the dyndns service. I linked my router to the dyndns account and host service. I portforward the ports my cameras are assigned. Up to this point its all good, I can access the cameras and their settings pages while outside. However both the Java and ActiveX options for video streaming do not work. Even within the network, using their raw IPs to view the cameras the videos stream works.But putting in the hostname and port they are assigned brings up the camera page, but no video.I can only assume the ports the video and audio run on are seperate, as when I put one camera's IP in the DMZ host on my router, it works with the DNS. Unforunately I can only do that with 1, and I'd rather not do that at all.
View 6 Replies
View Related
Feb 18, 2013
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : V1
ISP : Kabel Deutschland
the firmware offers 3 different dyndns services. But opendns is not included, also there is no free field to choose protocol, server, password and network. Will this be updated in further firmwares?
View 3 Replies
View Related
Apr 3, 2012
Just got this & set it up today. Wanted to buy a couple more in the next few days; but wanted to test out the D-Viewcam service. The application (D-Viewcam) is not able to find my camera.I have 'ticked' the uPNP & the forward; tried to disable it as well. No luck.
Camera 942l is on ver 1.1
D-Viewcam = v 3.2
Both reside on the same LAN
I'm able to view the camera on the browser. And on my phone.
View 1 Replies
View Related
