Cisco Routers :: RV082 Protect-link Activated But Not Filtering
Oct 7, 2011
I have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button.
My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
We have just buy a Cisco Small Business Router, model RV082. I need to enable the content filtering, but we just realized that this equipment does not filter HTTPS urls, even with the solution "Cisco ProtectLink Web" the equipment does not filter HTTPS urls.
For example, if I type on my browser just [URL], the access blocked, but if I type HTTPS:[URL], the access is allowed!Is there any way to block urls with HTTPS?
I went through the install procedure outlined in the ProtectLink Gateway install manual and i activated the ProtectLink Web product through Trend Micro (which shows up through their web site as a registered product to me). It still doesn't show up as installed on the SA540 (under Administration/License Management screen). When I try to activate the product again, it shows as "Already registered". Trend has no idea why it won't work. They said Cisco sold the license, so try their support.
I use to be running on firmware 1.0.2.4 with ProtectLink-Web working great, but then it expired. Some time later I updated the router to 1.0.4.17 and purchased a three year subscription to ProtectLink-Web, followed the registration link on the router, obtained an activation code, followed the activation link on the router and activated the service, however it didn't activate on the router.
I try to activate again and Trend Micro's site just says that it's already been activated. I contacted Trend Micro support and they see the activation attempts on there end and they said everything should be working. They recommended a factory reset which I performed and then attempted activation again, and again their site says that the service has already been activated. And yet when I go to Cisco ProtectLink Web > License > Summary it just says: "Please activate ProtectLink License to display the license information" and wont allow me to access the features. What is going on? Could the firewall be blocking the service? I didn't have this trouble the first time I used ProtectLink with f/w 1.0.2.4
I will try to explain my problem as clear as possible but my knowledge about networks and routers is very limited.
I have a DIR-615 version:C1 firmware:3.13NA My ISP is ATT DSL Modem is Siemens SpeedStream 4100, it does not have a router built in Internet line is connected from wall to modem, to router, to PC.
after I upgraded the firmware I had no internet coming out of the router, I bypassed the router and connected straight to the PC and I got internet. I unplugged the power on both modem and router waited a whole night (I was too tired) and in the morning internet was back to PC and I had WIFI again BUT. When I put a password on the WIFI network all my stuff finds the signal but cannot connect, if I open the signal meaning if I have no password and the WIFI is open I can connect all of my electronics without any problems.
I already tried using WEP and WPA but still unable to connect anything, I been leaving my signal open when I'm at home for the last week and I don't like it.
Before the update everything worked fine.
I don't know if this matters but I have a PS3, Wii, Roku box, Laptop and a couple cell phones connected to it. And there are like 6 or 7 network signals close to my house.
I am making my wireless network with Wireless router DIR-600 and DWA-525 desktop adapters for my office. I created a most secured type of network WPA2. And I have to create profile for DWA-525 desktop adapter to connect to my network and it requires the network secret key to connect. But This secret key is viewable from the "Network connection manager" when one can click on modify network and click on "Show text in the password field" by everyone using this computer (I mean by all other office staff). I don't want to let any one know my wireless network secret key. Is there any way to protect the key while having the computers automatically connected to wireless network. More information is below
Model: DWA-525 Hardware Version: A1 Firmware Version: 1.10 Operating System: Windows 7 Service Pack: 1
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
I have come across articles mentioning that URL Filtering can be implemented by using ASA 5505 with URL Filtering Servers. But Websense and other Web Filtering Servers are paid ones ? Are there any free solutions available ? What exactly is N2H2 ? The reason is I don 't want to increase the CPU utilization of ASA by implementing URL filtering within the device. If I have around 30 nodes which connects to the internet via a 2Mbps line through ASA 5505 and if I want to block around say 10 or 15 URLs , will it increase CU utilization beyond permissible limits ? Currently the CPU Utilization is around 10 - 15 . Here's the infrastructure setup .
I tried to find an answer to my issue however came up short. Did find,url... but that for a 600 not 601. I have "Mac filtering on and to only ALLOW the addresses below" however, it allows any computer, even if i do not have them listed.
I have dlink dir-600 router and I want to block access to website [ URL] for only one PC connect to router. i can either block web access to both PCS connected or block entire web access to one PC.
I have added a list of Mac numbers for allowed devices & checked the enable mac filtering box,but did not check the block box.All the Mac number devices, cannot access the wifi.But if I uncheck the "enable mac filtering box"all the Mac number devices can access the wifi.This also include other devices not in the list can also access to the wifi.It seem that the router can only block mac number BUT cannot have "allow list"I checked my firmware = 1.00.22 (Aug31 2000 14.36.01)Is this the latest firmware??
I have added a list of Mac numbers for allowed devices & checked the enable mac filtering box, but did not check the block box.
All the Mac number devices, cannot access the wifi. But if I uncheck the "enable mac filtering box" all the Mac number devices can access the wifi.
This also include other devices not in the list can also access to the wifi. It seem that the router can only block mac number BUT cannot have "allow list"
I checked my firmware = 1.00.22 (Aug31 2000 14.36.01) Is this the latest firmware?
It seems (and should be) pretty straight forward; under ADVANCED go to WEBSITE FILTERING and enter in the URI, or partial URI, that you want blocked and make sure the drop-down menu is "DENY computer access to ONLY these websites". The only problem is, I can still get to all of them. I saw in another forum that you had to check "Enable Access Control" and go through a 6-step process where you specify machines - I truly hope that isn't the solution, because it's needlessly complicated for most users who only want to block ALL devices on their network from accessing certain sites. My Hardware Version is B1 and my Firmware version is 2.00NA.
I can connect to the internet after 5mins or so after booting up but after that internet will not respond at all.i need to restart again my PC in order to connect again to the internet i somehow manage to bump with this solution using ping command.whenever i boot my pc i need to open this command and i can surf the internet without getting my connection lost just as long ping command is open.
I'm interested by the router Cisco RV180 or RV180W.
So as to increase security, i would like to set a MAC adress access restriction for all peripherals that would be connected to the router (10 computers, 2 servers, 6 Synology NAS) : only allowed MAC adress should access to the internet and network ressources.
Does the Cisco RV180 or RV180W have an IP to Mac biding feature and a Mac adress restriction feature ? If yes, how many peripherals/computers can be set ?
For example, only 30 mac/IP adress can be allowed on my actual router and it is not enough.
DIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)
I would like to know how to configure my DIR-600s firewall UDP Endpoint Filtering. I ve read some guides and I ve got to configure this to Endpoint Independent in order to play League of Legends. The problem is that I can see the option Firewall & DMZ but then I don't see the UDP or TCP Endpoint Filtering options.
I have had a great experience with my old DIR-655 (rev A) router. However, I would like to upgrade to a newer and better D-link router for my home that contains many well-connected children. Which routers are like my DIR-655, and have better overall performance than the DIR-655 without necessarily using the benefit of the 5 GHz second band. What better performing routers can record more than 24 MAC addresses in the Network Filtering area? I understand many people don't agree with MAC address filtering, but I like it to keep my kids from giving out my network password to all the neighbor kids and their friends too. So, MAC address filtering works for me. Or, should I just get an updated version of the DIR-655?
I got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0 mask: 255.255.255.0 gateway: 192.168.188.2 hop count: 1 interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup Local Security Gatewaytpe: IP Only Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
