Wireless Must Be Manually Activated After Start Up And Button Is Clicked
Jun 14, 2011
I got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
I have problem in recently installed LMS 4.1 Device discovery will not start when launched manually. When i hit the button, it doesn't even give a popup window saying that the discovery is started and that email will be sent... If I schedule it is launched, runs and finishes correctly. All proceses are started and it seems that application is working ok. LMS is installed on Win 2008 R2.
I've had my WRT110 for about 3 years or so, and it has worked fine for a long time. Today my computers were connecting to the router, but weren't getting internet access so I did the following:
checked lights on router and modem, they all indicated everything was working and normal Reset Modem,Reset Router,Still nothing. Called Comcast, they said everything was working fine from their end.Plugged my laptop into the ethernet connection on router.Plugged laptop directly into modem and it works fine.I saw the link on here to setup the router, and I have 0s on the internet ip, like it suggests at the end. When I click on the "release" and "renew" buttons nothing changes.
Since I moved our WLC Controller ( 5508 ) from Version 7.0 to Version 7.2.111.3 I got above failure messages. Until now I changed the radius timeout from 2 to 10 seconds and also I disabled the aggressive failover without success. What else it could be ?
I can connect to the internet after 5mins or so after booting up but after that internet will not respond at all.i need to restart again my PC in order to connect again to the internet i somehow manage to bump with this solution using ping command.whenever i boot my pc i need to open this command and i can surf the internet without getting my connection lost just as long ping command is open.
I have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button.
My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
I got a problem yesterday with a customer that says that the calls from a CISCO IP Phone 7961 to an Alcatel 4018 IP Touch didn't work, well the phone rings but there's no voice; I manage a CISCO ASA version 8.2(1) and I was checking the Inspection Rules in the Service Policy Rules section and when you open the inspection_default at the Rule Actions tab I find that the H.323 H.225 and H.323 RAS box wasn't checked so I ask to the customer to made a test and the same problem happen so I checked both box and again ask to the customer for a test and it works.
I was talking to a partner and he said that maybe this Inspect fix some signaling parameters of this protocol that can't work fine behind of a firewall.
I have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
I recently upgraded my WRT610N to Firmware Version: 2.00.01 and now the unit powers down on its own after a few hours. Are there any known issues with this firmware?Is there any way to roll back to the previous version of the firmware?
My wireless network consists mainly of approximately 1400 AP's 900 x 3602's, 500 x 3502's,The majority of these AP's especially the new ones have been manually optimised for channel and power settings. We paid an external surveyor to survey and optimise the AP's.
We have a few 5505 WLC's and the channel assignment method is set to "Freeze" ,My question is, if someone invokes a channel update on a WLC, will the WLC override the original manual channel setting if the WLC thinks it should be changed? And will the original setting be lost forever unless a restore is performed from the WLC Database?
I have 3 WAP321, all set to uk time zone, all the settings restor apart from the time on reboot that defaults back to 1999 despite NTP server listed, interestingly have to manually reset time to present before NTP will update it
We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
Region : Ireland Model : TD-W8960N Hardware Version : V4 Firmware Version : TD-W8960N ISP : Vodafone Ireland
I am having a rather annoying problem. I run a small hotel (just 3 floors) and my modem gives a strong enough signal to provide wireless access to everybody in the house however I'm finding that a lot of people, whilst they can connect to the modem, cannot browse online. Connection just times out when they open their browsers.Recently a guest gave me his laptop and asked me if I could do anything with it. I'm by no means an expert when it comes to this kind of thing so I chanced my arm by putting his MAC address into the CP's Wireless/MAC Filter page. He connected immediately and was able to go online much to my relief.
Thing is, I don't want to have to do this for every guest that comes through my door! Is there any way everybody who has a laptop can connect without me manually entering their MAC addresses? MAC restrict mode is set to 'disabled' but I thought that would allow everybody unrestricted access?
i have a problem with our new 5508 wireless controller (7.0.116.0).
Port 1 is the system default "management" (Port 2 is backup). Dynamic AP Management is disabled. Port 3 is a new dynamic interface "ap-manager 2" with Dynamic AP Management enabled and has a ip in a seperated VLAN which is not routed.
When i am connecting the AP (1260 series) to the "ap-manager 2" interface, then it will not join and i get an error message on the WLC:
*spamApTask1: Mar 05 14:52:12.783: %CAPWAP- -DISC_INTF_ERR1:capwap_ac_sm.c:1453 Ignoring discovery request received on non-managementinterface (3) from AP
When i am connecting the AP to the "management2 interface, then it is working fine. But i don't want the APs in the Management LAN. I want them in the separated no routed LAN explicit for the APs.
We have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.
We have about 20 of the above WAPs in our company network and are quite satisfied with the performance.However occasionally we need to manually reboot the WAPs in order to resolve sporadic connectivity issues that cannot be resolved on the client devices. In order to optimize the performance we would like to automatically restart our WAPs at a certain time (e.g. at night) on a daily or weekly basis.We are currently using WAP4410N-fw-2.0.0.5-K9.
I am trying to connect my LED Samsung Series 6300 TV to the internet. I have Samsung wireless LAN adaptor WIS09ABGN inserted into TV and I am using LINKSYS wireless home router WRT12ON-CA.
how do I block IP/Internet Adresses for ALL users without adding the sites manually per user in the Parental Control panel? I want to block a certain IP/internet adress for all users but can't find this feature within my EA6500 anywhere?Is this a firmware bug? Has linskys forgotten that some sites want to blocked for all users and how do I do it all in one?
i have a laptop that has a wireless button on the front and every time i try to click it to turn it on, it wont even blink. On the wireless networks, all it says is hat no connections are available. get my wireless network button on my laptop to turn on somehow?
i have an hp laptop that has a wireless button on the top right hand of the typing area. It has turned red before and all i had to do was push the button and it would turn gree. It has gone red again and when i push the button it stays red.
My keyboard was broken so plugged in a USB keyboard that doesn't have a fn button. I must have accidentally pressed something as my comp is asking me to turn in the wireless capability. There is no button on the computer and the light for wifi is off. How to turn this back on with a keyboard that does not have a fn button?
i have an hp laptop that has a wireless button on the top right hand of the typing area. It has turned red before and all i had to do was push the button and it would turn gree. It has gone red again and when i push the button it stays red.
Just installed windows 8 on this laptop, everything is working fine, it has all the drivers etc. It does not seem to be picking up wireless for some reason. When I press the quick launch button for wireless absolutely nothing is happening, however it can pick up internet with the ethernet cable from the modem. Had a read of this and tried to install the FSC Launch Manager from the Fujitsu website still to no avail. Cant be the operating system either as it the same problem arose when i install a version of xp yesterday.
I'm having problems with the wireless button after I took my laptop apart to clean. The wireless button won't switch on at all and doesn't light up. When I press fn f8 nothing happens. I'm not sure what I've done. The wires are correctly in place as far as I can tell. I've tried the following things:Uninstalling the adapter in device manager and rebooting /Checked adapter is listed as working properly /Do a system restore /Check BIOS
I am trying to set a wireless connection and it says that the Wifi isn't on, which I believe, because I don't even know where the Wifi button is. And the computer didn't come with an owner's manual with a diagram of where and what every button is. Trying to set up PC for bf for Christmas. I am a mac user :P so I have lost my touch with PC's.
