i have an hp laptop that has a wireless button on the top right hand of the typing area. It has turned red before and all i had to do was push the button and it would turn gree. It has gone red again and when i push the button it stays red.
View 1 Repliesi have an hp laptop that has a wireless button on the top right hand of the typing area. It has turned red before and all i had to do was push the button and it would turn gree. It has gone red again and when i push the button it stays red.
View 1 Replies View Relatedmy wireless on my computer says that it is not enabled... how do i enable it? i do not have a wireless button, and my computer defonately is wireless?
View 1 Replies View RelatedMy f5 button isn't working and now I cant turn on my wireless internet.
View 1 Replies View Relateddcm425 dont turn off also has 4 solid green lights...it happen after a power outage my router works fine but my dmc425 cable modem just has the 4 green solid lights when it's plugged in when i push the power button nothing happens at all
View 3 Replies View RelatedIs there any way to turn off the front green LED on the DCS-930L or do I just cover it with a piece of opaque tape?
View 2 Replies View RelatedFor the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
View 1 Replies View RelatedI've got a Dell N5010 with Windows 7, after dropping my laptop and breaking the hard drive I replaced it with one I bought from Amazon, all is well apart from I now have to use an external antenna for WiFi to work. Without it I just get ' No connections are available'. I also can't turn off the touchpad with the button to the right of F12 like I used to. I read somewhere it might be to do with the Dell Drivers CD?
View 1 Replies View RelatedI can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems
attempted to fix problems via belkin software
changed channels on modem
updated firmware
etc, etc
I have 3 1142N AP's. I plugged them in one at a time here at my desk and they work fine. When I take them upstairs and install them only one of them works. I can move the working one to the other locations and it still works. The LED flashes continously green on the other two.
View 4 Replies View RelatedJust had some more 3500i installed,but 2 of these seem to be working, but there is no green LED when no connection, and when you conneect there is no blue led. The LEDs to change when rebooting the AP, just neve seen this before, is this a fault?
View 5 Replies View RelatedI have two LAP1041 with WLC2504 everything works fine. But since yesterday when it boots up it flashes green, then solid green, then after about 10 seconds the green LED turns off, however the LAP is still working fine, Why is that? If I put my eyeball up close to the LED I see dim red inside the LED plastic cover.
View 3 Replies View RelatedRecently we had a situation where our users were unplugging one of our un-mounted 1252 LAPs. They would do this so they could borrow the wire to direct connect any one of their devices not realizing they were disconnecting a wireless access point. After discovering that the AP was unplugged once again, our admin plugged the AP back to the network but noticed that it no longer would connect to the controller. We can no longer console into the AP but can console into all other APs we have. All 3 lights are now green. Radio and Ethernet are solid and Status is blinking. I found the Cisco doc explaining the meaning of the front panel lights but have not found this particular configuration. What these lights mean and why not being able to use the console port?
View 11 Replies View RelatedI'm having a strange issue with an 1142 AP. I have a 5508 WLC at my corporate HQ and have AP's in many locations, connected by MPLS WAN. I have one site where the 1142 is blinking green and doesn't associate with the WLC. I have tried a different switch port with the AP (didn't work) and I know that the switch port is good because I have a 1252 that works just fine at this remote location.The really weird part is that the AP is blinking green, but the switch port shows that it is not connected and the green port light on the 3560 switch is not lit. I have verified wiring in the closet, but unfortunately the 1142 AP is hanging 40ft high in a shop and I don't have access to it.Is it possible that there's a bad rj-45 termination that is allowing PoE to the AP, but no data?
View 14 Replies View RelatedI recently upgraded my ADSL to a 1Mbps line and I got a new Fritz box(7390) with it and i bought a linksys ae3500 wireless router. I am using Bit comet to download my torrents and my listen port stays at a yellow light. I previously had only the Fritz box 7170 and my listen port was always green.
View 1 Replies View RelatedI have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies View RelatedAfter the upgrade of the WLC 5508 to version 7.4 the 1142 access-points LED blinking rapidly cycling through blue, green, and red. I found the following information to this behavior: "Access point location command invoked"
The configuration didn't change. How can I switch this function?
Recently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
I am trying to connect my LED Samsung Series 6300 TV to the internet. I have Samsung wireless LAN adaptor WIS09ABGN inserted into TV and I am using LINKSYS wireless home router WRT12ON-CA.
View 1 Replies View RelatedI have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies View RelatedI'm installing the first out of 10 Aironet AP's with an inline injector. The lights on the Aironet and alernating blue, green, red. I know the error code is for DHCP, but when I plug it in I see the AP on my DHCP server and it does pull an IP address. I can ping the ip address, but I cannot access it through my browser.
I have tried deleting the entry out of the DHCP and power it back on again. I have also tried another unit with the same results. I don't have a RJ-45 to serial cable.
3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
i have a laptop that has a wireless button on the front and every time i try to click it to turn it on, it wont even blink. On the wireless networks, all it says is hat no connections are available. get my wireless network button on my laptop to turn on somehow?
View 7 Replies View RelatedMy keyboard was broken so plugged in a USB keyboard that doesn't have a fn button. I must have accidentally pressed something as my comp is asking me to turn in the wireless capability. There is no button on the computer and the light for wifi is off. How to turn this back on with a keyboard that does not have a fn button?
View 1 Replies View RelatedJust installed windows 8 on this laptop, everything is working fine, it has all the drivers etc. It does not seem to be picking up wireless for some reason. When I press the quick launch button for wireless absolutely nothing is happening, however it can pick up internet with the ethernet cable from the modem. Had a read of this and tried to install the FSC Launch Manager from the Fujitsu website still to no avail. Cant be the operating system either as it the same problem arose when i install a version of xp yesterday.
View 6 Replies View RelatedI'm having problems with the wireless button after I took my laptop apart to clean. The wireless button won't switch on at all and doesn't light up. When I press fn f8 nothing happens. I'm not sure what I've done. The wires are correctly in place as far as I can tell. I've tried the following things:Uninstalling the adapter in device manager and rebooting /Checked adapter is listed as working properly /Do a system restore /Check BIOS
View 4 Replies View Relatedwhere is the button to turn on the wireless for a HP 2000 notebook pc?
View 1 Replies View RelatedI am trying to set a wireless connection and it says that the Wifi isn't on, which I believe, because I don't even know where the Wifi button is. And the computer didn't come with an owner's manual with a diagram of where and what every button is. Trying to set up PC for bf for Christmas. I am a mac user :P so I have lost my touch with PC's.
View 1 Replies View RelatedI got a new HP laptop running Windows 7. When I turn on my laptop, my wireless is off. So I click on F12 (my wireless button), to activate my wireless. The orange light turns blue. Even though the light indicates that my wireless is on, I have to go to device manager>networking>802.11n>advanced then activate my radio for my laptop to pick up the wireless signals. The problem is that I have to do this every time I turn on my laptop, and its getting quite repetitive.
View 4 Replies View RelatedHave a westell wireless router, where is wps buttob
View 2 Replies View Relatedmy werelss doesn't work becuase radio switch turn of and i can't turn it on
View 2 Replies View RelatedI just got my new router today but i don't see a power button on the back of this unit. Am i blind? Of course the unit comes on when i plug in the adapter but i don't see a on off switch.
View 7 Replies View RelatedI have a Linksys Wireless Router, model WRT54G. I read in the user manual that it is best to turn off the router when not in use for better security measures, but there in no power button on the router. So does this mean that the power cord would have to be unplugged from the electrical outlet each time to turn the router off? This is kind of inconvenient, especially where my cord is plugged in. Also would unplugging it from the outlet each time, would this mess up the settings on the router? Is it really necessary to turn it off?
View 9 Replies View Related