Just had some more 3500i installed,but 2 of these seem to be working, but there is no green LED when no connection, and when you conneect there is no blue led. The LEDs to change when rebooting the AP, just neve seen this before, is this a fault?
View 5 RepliesAfter the upgrade of the WLC 5508 to version 7.4 the 1142 access-points LED blinking rapidly cycling through blue, green, and red. I found the following information to this behavior: "Access point location command invoked"
The configuration didn't change. How can I switch this function?
I'm installing the first out of 10 Aironet AP's with an inline injector. The lights on the Aironet and alernating blue, green, red. I know the error code is for DHCP, but when I plug it in I see the AP on my DHCP server and it does pull an IP address. I can ping the ip address, but I cannot access it through my browser.
I have tried deleting the entry out of the DHCP and power it back on again. I have also tried another unit with the same results. I don't have a RJ-45 to serial cable.
Just upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 10 Replies View RelatedFor a Campus setup (University), if I deploy 1142 AP's on all the floors with a WLC controlling them, and put one 3500 AP on each floor, will that give sufficient Clean Air support with automatic Rogue elimination? What about if an AP drops, does the WLC automatically try to cover that area with neighboring AP's? I know the old WLSE would be able to do that, but not sure if the WLC can do that by itself. What part of Self Healing can the WLC do with Clean Air, or is a WCS a must have in order to automatically Defend and self heal? Also is the MSE needed for this if a WCS is used? What does the MSE do that the WLC and WCS can't?
View 4 Replies View RelatedI can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems
attempted to fix problems via belkin software
changed channels on modem
updated firmware
etc, etc
I have a dual 5508 controller /NCS deployment. I deployed my first clean air AP today, a 3502I.
The Clean Air feature does not seem to work, however. "No information is available because CleanAir is disabled or otherwise not available for this radio. If no information is available and CleanAir is enabled then you can try rebooting the AP XXXX".The thing is that CleanAir is enabled on this AP.
I am planning on installing Clean Air Wireless network, using WLC 5508, WCS(with plus license) and MSE.
Which MSE license i need to get this to work ?
We have installed a number of Cisco Wireless 3502-07 in China and i can not get the Clean Air Oper status to change to UP. At the meoment i have ERROR. I have have tried to disable and enable the the Clean Admin Status from the Access Point 802.11b/g/n and then select the AP and change configuration.
View 2 Replies View RelatedI've just installed a clean Windows 7 Ultimate on a brand new Acer Aspire 5750.The lan nor wireless didn't work out of the box. After installing the Gigabit lan drivers it found the network card But it can't find the wireless. When I try to install the Wireless drivers from: [url]It's the Atheros card I have. So when I try to install the Wireless Lan Atheros drivers it sais:"The device doesn't exist. Please plug the device back in and try again" What do I do now? It's a laptop, I can't exactly remove the network card.
View 1 Replies View RelatedI have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 9 Replies View RelatedThis is about to cause me to buy another router. This will be the 4th clean install that I have had to do. If my power, or my internet goes down, a regular proper reboot / or reset, will not get my ea2700 back online. It takes uninstalling & deletion of the stored Application Data files.
View 8 Replies View Relatedcant get my blue ray to connect to wireless. on network connection test it stops on gateway ping?
View 1 Replies View RelatedMy sony blue ray player lost it's connection to my wireless lnyskis router. I can't reconnect it.
View 3 Replies View RelatedI have 3 1142N AP's. I plugged them in one at a time here at my desk and they work fine. When I take them upstairs and install them only one of them works. I can move the working one to the other locations and it still works. The LED flashes continously green on the other two.
View 4 Replies View RelatedI upgraded processer, ram and mobo, clean install vista ultimate wg311v3 wireless card, all signs and data shows im connected to the internet. But i can't get to any webpage.. i downloaded sp1 and sp2 on a diff computer and put them in but no luck.
View 3 Replies View RelatedI have a HP Pavillon dv6000 laptop, tried connecting to my wireless network this morning but no luck. It will connect fine when using Ethernet cable. Whether the switch is pushed to on or off the light stays orange, when it is connected it used to turn blue. I've included a prtscrn of my device manager...
View 3 Replies View Relatedi have an hp laptop that has a wireless button on the top right hand of the typing area. It has turned red before and all i had to do was push the button and it would turn gree. It has gone red again and when i push the button it stays red.
View 1 Replies View Relatedi have an hp laptop that has a wireless button on the top right hand of the typing area. It has turned red before and all i had to do was push the button and it would turn gree. It has gone red again and when i push the button it stays red.
View 1 Replies View RelatedIn my lab I have a Guest Wireless network setup and fully functional. Here is a brief diagram:
Client -> AP -> LAN switch and WLC-Foreign -> Core router -> DMZ switch and WLC-Anchor -> Edge Router -> Internet
I have NME for credential management on the LAN as well.The WLC-Foreign is a 5508.In my DMZ, I have two networks - 1 for normal DMZ management and 1 for Guest Wireless.
I now have to add a Blue Coat web proxy appliance into the DMZ and have Guest Wireless traffic pass through it. I have tried multiple scenarios including connecting the WLC-Anchor to the Blue Coat directly and making the Blue Coat the gateway for my Guest Wireless network. Any good design for the DMZ networks and/or routing to enable the Guest Wireless traffic to go to the Blue Coat and then out to the Internet?
My e1000 router (v 2.1) has reset itself and after that all lights except the wireless adapter has gone solid blue, I have no ethernet conectivity and hard reset the router did not work.
View 9 Replies View RelatedI have two LAP1041 with WLC2504 everything works fine. But since yesterday when it boots up it flashes green, then solid green, then after about 10 seconds the green LED turns off, however the LAP is still working fine, Why is that? If I put my eyeball up close to the LED I see dim red inside the LED plastic cover.
View 3 Replies View RelatedRecently we had a situation where our users were unplugging one of our un-mounted 1252 LAPs. They would do this so they could borrow the wire to direct connect any one of their devices not realizing they were disconnecting a wireless access point. After discovering that the AP was unplugged once again, our admin plugged the AP back to the network but noticed that it no longer would connect to the controller. We can no longer console into the AP but can console into all other APs we have. All 3 lights are now green. Radio and Ethernet are solid and Status is blinking. I found the Cisco doc explaining the meaning of the front panel lights but have not found this particular configuration. What these lights mean and why not being able to use the console port?
View 11 Replies View RelatedI'm having a strange issue with an 1142 AP. I have a 5508 WLC at my corporate HQ and have AP's in many locations, connected by MPLS WAN. I have one site where the 1142 is blinking green and doesn't associate with the WLC. I have tried a different switch port with the AP (didn't work) and I know that the switch port is good because I have a 1252 that works just fine at this remote location.The really weird part is that the AP is blinking green, but the switch port shows that it is not connected and the green port light on the 3560 switch is not lit. I have verified wiring in the closet, but unfortunately the 1142 AP is hanging 40ft high in a shop and I don't have access to it.Is it possible that there's a bad rj-45 termination that is allowing PoE to the AP, but no data?
View 14 Replies View Related-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies View RelatedRecently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
I have an e1200 Linksys router hooked up and working well, a wired connection to my first computer a wireless connection to my second (laptop) in the basemen and to my HDTV. My question is what Linksys device would I need to enable me to get a wireless connection in the basement to then hardwire connections to my Blue-Ray player and my HK AVR-3650.
View 2 Replies View RelatedI am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]
View 6 Replies View RelatedThe problem am having is that my Users can get to the internet on the LAN but cannot get to the internet thro the WLAN. Below is the cisco equipment used to setup the WLAN and LAN. I dont have any clue as to why users cnnot get to the internet from the WLAN except the LAN.
ITEMS
1.
CISCO CATALYST 2960-S
Part Number: WS-C2960S-24PS-L
10
Part Number: CON-SNT-2960S2PS
10
[code]....
So I'm going to bridge two Cisco AP's 1260 and 3500, which have an 880 router on each side.
(Currently I have a VPN set-up through the internet for the two locations to communicate) (Naturally they are currently in different subnets) Will absolutely change this and set up as one subnet. There is VLANs setup on each router (same VLANs)
VLAN 1
And
VLAN 10
Everything is configured on the Routers and AP's for these VLANs (works flawlessly over the VPN).
So now since I’m going to get rid of the VPN and set-up a bridge with two AP's, will having same VLANs across both routers be a problem? Will VLANs work OK through the bridge?
Besides using (IP helper address DHCP-IP) command on the non-root bridge side router to forward DHCP requests to the root bridge side router, Also I want to be able to route internet traffic on the non-root bridge side through the WAN port, and only route LAN traffic through the bridge..
We have couple of Cisco Aironet 3500 Series access points with the following P/N: "AIR-CAP3501E-A-K9", we have discovered that we need a wireless LAN controller to connect those new access points!, however, we do not have any wireless controller in our LAN.
We even tried to CLI through the console port but we could not set any static IP on it!, after reading on Cisco site we discover that this type of AP is called "Lightweight Access Point" LAP which handles all the management tasks to the controller!
So what shall we do! is it impossible to operate them without the controller?
We have had several APs disassociating from our controllers. The alerts say, Message: Access Point 'AP-xxxxx' associated to controller '10.x.x.x' on port number '0'. Reason for association 'Dot11g Mode Change. I have read several posts that point out that you should have QoS implemented to prioritize the CAPWAP traffic. I'd like to know if someone has implemented QoS and whether it has been successful in stopping the APs from disassociating. And if it has been successful do you have any configuration examples for the ports attached to the AP and controller as well as the QoS configuration?
We have several sites with AP1142's and 3500's. We have 2 5508 controllers. We are broadcasting 2 SSIDs of which one is in HREAP mode and the other is in local mode. Each of our sites have MPLS circuits.
Here is an example I found on Cisco which I believe can be used for CAPWAP as long as you change the ports to 5246 & 5247 instead of 12222 & 12223.
Example Router Configurations #
This section contains router configuration examples to be used as guides when addressing CS6 remarking or LWAPP control traffic load.
#
This example uses LWAPP APs on the 192.168.101.0/24 subnet, and two WLCs with ap-managers at 192.168.60.11, and 192.168.62.11. (code)