We have installed a number of Cisco Wireless 3502-07 in China and i can not get the Clean Air Oper status to change to UP. At the meoment i have ERROR. I have have tried to disable and enable the the Clean Admin Status from the Access Point 802.11b/g/n and then select the AP and change configuration.
View 2 RepliesThe problem is WiSM module not coming in OPER-UP status , it’s in Started-Keepalive status.I did run debug wism events on cat6509 and seeing below logs:
[code]...
It’s receiving garp request from controller and assign ip to controller but then keepalive time expired and it’s put the controller in started-keeplaive status.
I have one 5500 and about 15 Cisco 3502 APs.
The problem is that one of the clients loses the connection to the network time to time ,The error in the WLC logg is
*Dot1x_NW_MsgTask_0: Jul 06 17:42:38.934: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:843 Received EAPOL-key M2 msg has invalid information when mobile is in START state - invalid secure bit; KeyLen 24, Key type 1, client 00:21:6a:af:be:70
1552 E Ap with a 2504 WLC. Single Root Ap with Mesh the Mesh has the problem. Both Power Injector and AP has been replaced . How do you turn on the 802.11 B Radio? No other problems at 40 other sites with identical installation.
View 1 Replies View Relatedive just installed Cisco Prime LMS 4.1 on a Windows Server 2008 machine. when i try to open some features. like topology or the VLANs configuration options in the configuration menu i get the error HTTP STATUS -500 and this:
type Exception report
message
description The server encountered an internal error () that prevented it from fulfilling this request.
exception
javax.servlet.ServletException: Servlet execution threw an exception
[code]....
I am trying to generate bug summary report from RME but once job completes i can not see/view report. whenever I am trying to click on view under job result to see reports I get apache/http error. snap shot is attached for reference.
I am running LMS 3.2.1 and RME 4.3.2.. struggle alot to reach this stage where I can see report are getting generated for PSIRT and bug summary..but can not see report for Bugs though I can see PSIRT report...
I have a Cisco Wireless LAN Controller AIR-CT5508-K9 running Software Version 7.0.98.218. This WLC has registered ten AP model 1240.Now I have configured fiive CAP3502 with static capwapp commands, when I connect the CAP-3502 in the network, in the WLC I see the status "downloading" then the CAP restart, and the console show the message *Mar 1 00:15:39.033: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER, and never the CAP3502 is registered in the WLC. [code]
View 1 Replies View Relatedi have 2504 controller with 7.0.116.0 software and some 3502 APs. I also using 5 APs now and few days ago I bought some additional 3502 APs and I can't get them connected to the controller. My company admins decided to using DNS controller discovery instead of using DHCP option 43. I'm connecting APs to access ports of Linksys switches and APs not in the same subnet as ap-manager interface of controller. AP succesfully get IP and DNS from DHCP and could ping cisco-capwap-controller. However, I have such messages.
*Mar 1 00:12:32.014: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Not in Bound state.
*Mar 1 00:12:40.533: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
I can succesfully ping controller from AP AP30f7.0d2e.9a58#ping cisco-capwap-controller Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.23.16.30, timeout is 2 seconds:
There are a total of 25 Cisco 3502 APs installed. 24 APs were discovered except for 1 AP. I run SH CDP NE on the switch and the AP was discovered by the switch but it does not have an IP address. On the output of the SH CDP NE DE, I noticed that on the AP that is not joining, the Platform is "cisco AIR-SAP3502E-E-K9" while the APs that joined the WLC, the Platform is "cisco AIR-CAP3502E-E-K9". The software versions are also different but this could be because the WLC already upgraded the IOS when the APs joined.Why is the Platform "SAP3502E" for the AP that did not join.
View 9 Replies View RelatedJust a basic question regarding MAC based authentication of AP with ACS. The scenario is - If I have a ACS installed and I want all my Cisco 3502 APs to be authenticated on MAC basis via ACS. I know that AP mac is used as a username and password at ACS so that whenever we plugin the new AP in the network, it gets authenticated via ACS first and if the AP is authorized to be used in network then only it gets the IP address from DHCP.
My question is - What will happen, if the AP is connected in local mode on a remote location and the WLC, ACS & DHCP are in Data center. The traffic coming from remote location will pass through the Remote-site router and during that pass, it will remove the source mac address of AP and put the router interface MAC address as source, so how will the ACS authenticate the AP in that case.
When working in a LAN I know its possible, but how will it work over the WAN.
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
I have a Cisco WLC5508 controller which I recently upgraded to software 7.0.98.0 because I tried to add a Aironet 3502 and it gave me an invalid software. After the upgrade this is the error I get from the AP when I try to add. [code]
View 5 Replies View RelatedOur newly installed WAP's are constantly downloading code and seem to lose contact with our wism 1 version 7.0.235.3, causing them to restart the downloading process, over and over.
View 12 Replies View RelatedWe have a secure ssid and a guest ssid. Is the a way to prompt for a single username and password and if that name is guest it will automatically connect to the guest ssid? If active directory user and password it will automatically use the secure ssid? we are using Microsoft NPS/Radius, 3502 ap's, and 5508 controller.
View 3 Replies View RelatedI found the 3502 waps are plenum rated, I found the cable on the antenna are plenum rated, but are the antenna plenum rated?
AIR-ANT5160NP-R?
AIR-ANT2451NV-R?
AIR-ANT2460NP-R?
I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
I have a 3502 AP that I am attempting to set back to factory default including clearing the username and password. It is going to work off of 4400 controllers. I have read numerous documents no how to clear the config and password but so far nothing has worked. I can get it into ap: mode but not sure what to enter here. When I do a dir there doesnt seem to be any files. It will pull an IP address via the local router but cannot communicate with WLC.
View 28 Replies View RelatedI am trying to configure a 1242 or 3502 WGB with PEAP. There is not ACS server involved as Windows RADIUS is used. I can get the WGB to work with OPEN Authentication but when I attempt to add in the authentication/security piece I get "no association." Below is my current config. The WLAN is set to use WPA/WPA2 802.1x + CCKM.
Current configuration : 1812 bytes
!
! Last configuration change at 00:56:39 CST Tue Mar 2 1993
version 15.2
[Code].....
I am trying to locate the radiation pattern for a 3502 with an internal antenna. We have some high ceilings so the elevation pattern could impact our placement strategy.
View 6 Replies View RelatedJust had some more 3500i installed,but 2 of these seem to be working, but there is no green LED when no connection, and when you conneect there is no blue led. The LEDs to change when rebooting the AP, just neve seen this before, is this a fault?
View 5 Replies View RelatedI have a dual 5508 controller /NCS deployment. I deployed my first clean air AP today, a 3502I.
The Clean Air feature does not seem to work, however. "No information is available because CleanAir is disabled or otherwise not available for this radio. If no information is available and CleanAir is enabled then you can try rebooting the AP XXXX".The thing is that CleanAir is enabled on this AP.
I bought a used Aironet 3502 (air-cap3502i-a-k9) on craigslist last week and the seller said it was set up for autonomous mode. It has ap3g1-k9w7- tar. 124-25d.JA, which does allow it to run without a controller. I know it's not the latest version, but without a service contract I'm unable to access the latest firmware. When I go into the web management console, it only shows wireless N, without letting me enable A/G. The product sheet shows it should do A/G/N - is this just a byproduct of putting the autonomous ios on a 3502, or am I missing a setting somewhere to enable it?
View 3 Replies View RelatedI am planning on installing Clean Air Wireless network, using WLC 5508, WCS(with plus license) and MSE.
Which MSE license i need to get this to work ?
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies View RelatedWe have been deploying 3502 APs remotely to locations with full T1s that backhaul to where I sit at HQ. Both the foreign and anchor controller are here at my location.
I am seeking to rate limit per user the bandwidth each client will get on the guest internet ssid. As you know this traffic is encapsulated in capwap between the AP and the controller so I cant use a standard ACL on the switch or router.
We are trying to keep the guest internet access usage in check on the T1 at any given site so the other ssid's & local lan traffic is not overly competing for the bandwidth.
I found the place to edit the default profiles in the controller but the documentation really isnt clear on best practices.
So I put it to you my fellow wireless engineers to suggest how you are implementing bandwidth management on your wireless guest internet.
Oh and here is my hardware & software levels.
5508wlc - forgeign
4402wlc - anchor
Software Version7.0.230.0
I've just installed a clean Windows 7 Ultimate on a brand new Acer Aspire 5750.The lan nor wireless didn't work out of the box. After installing the Gigabit lan drivers it found the network card But it can't find the wireless. When I try to install the Wireless drivers from: [url]It's the Atheros card I have. So when I try to install the Wireless Lan Atheros drivers it sais:"The device doesn't exist. Please plug the device back in and try again" What do I do now? It's a laptop, I can't exactly remove the network card.
View 1 Replies View RelatedI have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 9 Replies View RelatedThis is about to cause me to buy another router. This will be the 4th clean install that I have had to do. If my power, or my internet goes down, a regular proper reboot / or reset, will not get my ea2700 back online. It takes uninstalling & deletion of the stored Application Data files.
View 8 Replies View RelatedI upgraded processer, ram and mobo, clean install vista ultimate wg311v3 wireless card, all signs and data shows im connected to the internet. But i can't get to any webpage.. i downloaded sp1 and sp2 on a diff computer and put them in but no luck.
View 3 Replies View RelatedJust upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 10 Replies View RelatedI try to remplace WLC because the old wlc (7.0) is capacity full.but the AP (3502) do not "registered" to new WLC (7.3),If you have a idea, without make a reset factory to AP.
View 1 Replies View RelatedI try to replace WLC because the old wlc (7.0) is capacity full. but the AP (3502) do not "registered" to new WLC (7.3). Don't want to make a reset factory to AP..
View 3 Replies View RelatedFor a Campus setup (University), if I deploy 1142 AP's on all the floors with a WLC controlling them, and put one 3500 AP on each floor, will that give sufficient Clean Air support with automatic Rogue elimination? What about if an AP drops, does the WLC automatically try to cover that area with neighboring AP's? I know the old WLSE would be able to do that, but not sure if the WLC can do that by itself. What part of Self Healing can the WLC do with Clean Air, or is a WCS a must have in order to automatically Defend and self heal? Also is the MSE needed for this if a WCS is used? What does the MSE do that the WLC and WCS can't?
View 4 Replies View Related