I am trying to generate bug summary report from RME but once job completes i can not see/view report. whenever I am trying to click on view under job result to see reports I get apache/http error. snap shot is attached for reference.
I am running LMS 3.2.1 and RME 4.3.2.. struggle alot to reach this stage where I can see report are getting generated for PSIRT and bug summary..but can not see report for Bugs though I can see PSIRT report...
ive just installed Cisco Prime LMS 4.1 on a Windows Server 2008 machine. when i try to open some features. like topology or the VLANs configuration options in the configuration menu i get the error HTTP STATUS -500 and this:
type Exception report message description The server encountered an internal error () that prevented it from fulfilling this request. exception javax.servlet.ServletException: Servlet execution threw an exception
I am unable to generate bug summary report in RME. Even I can not generate PSIRT report as well..LMS always gives error "incorrect cisco.com credential. enter correct credential" I have checked my credentials are correct... it gives me error no BTKT:0014..I am using LMS 3.1 attaaching snap shot of my patch level and application version running on LMS...
I'm experiencing problems on two cisco switches connected on trunked ports via leased line. The remote site is connected to our main site and I'm getting some weird behavior.Only 2 VLANs are currently trunked and we're experiencing some intermittent connection issues. When sites are connected via trunked port everything works on VLAN 102 and everything on VLAN 101 except there are no internet connectivity, where hosts cannot ping default gateway or proxy.Switches connected are C2960 and C3550 with configuration which was working for 5 years without any issues. BT NTUs does not report any errors and connection seems to be fine. If I interconnect sites via switchport which is on VLAN 101 (staff vlan) everything works fine except student looses the services... because VLAN 102 traffic is not forwarded across the link.
Using Custom Reports from Reports> Report Designer> User Tracking to create an end host report we get this error message: the syntax is not valid the system cannot find the path specified.
I have installed LMS 4.0.1 again. Now LMS is running on a Windows 2008 R2, 64 bit. Using Custom Reports from Reports> Report Designer> User Tracking to create an end host report I get this error message: "The syntax is not valid: the system cannot find the path specified". Anyway, the report is created but I’m not able to edit or delete: it is not listed on Available Custom Reports.
1552 E Ap with a 2504 WLC. Single Root Ap with Mesh the Mesh has the problem. Both Power Injector and AP has been replaced . How do you turn on the 802.11 B Radio? No other problems at 40 other sites with identical installation.
We have installed a number of Cisco Wireless 3502-07 in China and i can not get the Clean Air Oper status to change to UP. At the meoment i have ERROR. I have have tried to disable and enable the the Clean Admin Status from the Access Point 802.11b/g/n and then select the AP and change configuration.
We're getting this error message randomly when surfing the Internet. We have websense running on our network to perform web content filtering and are using the ASA for the http/https redirects. We've contacted websense and they said this error message is coming from the ASA, not their product.
I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
logging enable logging buffered 7 access-list ALL line 8 extended permit ip any any
I am having pentium p3 zenith make,window xp sp3 is the operating system. Belkin router N150 is being used.,I am able to get connection through this router on other p4 pc of my friend.,but when I try to connect to my pc.,belkin router set up do not display.,and diagnostic network connection ,indicate that error 12007 could not connect to HTTP,FTP etc., IE 8 and mozilla firefox are installed and both give the same error i.e. connection to internet could not be established
I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map parameters message-length maximum client auto
When you configure an ABR to inject a summary route into an area, what are the circumstances under which the ABR will inject the summary? I.e., since it's not a set of specific subnets learned directly from other OSPF routers, does the summary get injected regardless of what's in the routing table of the ABR?
I would imagine this could cause problems in a situation where there is an ABR injecting a large summary into an NSSA that also has a backup path over the Internet (IPsec tunnel or something). For example, if the area 0 routers from which the ABR receives routes went down, the ABR would continue to inject the summary route into the NSSA thus tricking those routers into sending traffic to the ABR rather than over the backup link.
I can't imagine any other way an ABR would decide when it's suitable to inject the summary though.
I have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
I have setup a site to site VPN with an ASA 5510 (8.4) and a Cisco 2811. The tunnel is working fine, however both sites have 5 different contiguous networks. The crypto ACL between sites states only one subnet.Is it possible to state a summary address in an ACL rather than having five lines for the ACL?The tunnel works when the router uses an ACL of 10.2.200.0 0.0.7.255, however if a summary address of all the subnets on the inside network of the ASA are stated in an ACL - 10.1.200.0 255.255.248.0 - then the tunnel does not come up.Is it possible to state a summary address on a crypto ACL on the ASA?
In my Lab environment in GNS I have connected two 7200 series router through fastethernet on router A I have given IP adress 192.168.10.54 and router B I have given IP address 192.168.10.53 and default route as 0.0.0.0 0.0.0.0 192.168.10.53 and when I run the command on router A it shows result as follows "C 192.168.10.52/24 is directly connected ,Fast ethernet 2/0".
So I need to know why it's showing the result of .52 at last why not .53 or .54 at last what is the reason it's showing .52 which I have not mentioned in my IP address.
I have a 5508 WLC running on 7.0.116, I need to be able to pull all configured users off the WLC and import into excel, I have 900 odd users configured. When I run a show net user summary it only displays a third of users. I'm hitting space to tab through each page, then eventually I just get dumped back to the command prompt.
I have a Nexus 7K router, has 2 ospf process, ospf 1 and ospf2. OSPF1 has several subnets in 10.1.0.0/16 subnet range , OSPF2 has several subnets in 10.2.0.0/16 subnet range. I want to summary OSPF 1 subnets to 10.1.0.0/16 then redistribute to OSPF2. but it doesn't work. [code]
In earlier versions of LMS it was possible to choose i.e. the Routers category (top level) and enter a series of commands to be excluded from the comparison. In LMS 4.0.1 I experience, in several different installations, that this is not possible. It seems I can enter one exclude command beyond the defaults per category, the rest is not applied even though the feedback from the application is positive. Next time I access the Exclude Commands view, the commands I entered are gone. Is this a change of behaviour or a bug?
I have a layer 3 switch with a bunch of SVIs all in the 192.168.x.0/24 range. I just want to advertise a 192.168.0.0/16 summary to the BGP neighbors. I can do this either by:
1) Redistributing connected into BGP and then using the 'aggregate-address' command to advertise the summary.
2) Specifying a network statement in the BGP config for every single SVI, then using the 'aggregate-address' command.
3) Create a static route to null0 (ip route 192.168.0.0 255.255.0.0 null0) and put 'network 192.168.0.0 mask 255.255.0.0' command in the BGP config.All three fulfill the same purpose of summarizing all the SVIs, but creating the static route is much cleaner in this case. It seems like the aggregate-address command is mostly intended for routers that are aggregating connections coming from other routers and all of them share a common prefix.
if I can do the following deployment using a Cisco ASA5510 security plus.
At this moment I have two interfaces in use one (outside) with the IP: 172.16.21.254/24 and the other (inside) with the IP: 192.168.4.1/24. Now the customer needs to connect another network that works with the IP segment: 192.168.0.0/22.
The IP segment 192.168.0.0/22 goes from 192.168.0.1 to 192.168.3.254 that means that there is no a overlap with the network segment 192.168.4.0/24. My question is: If I configure another interface in the ASA that works in the segment 192.168.0.0/22 the routing table will auto-summary the network and merge it with the network 192.168.4.0 or will it leave the networks apart??
I don't user dynamic routing protocols but I cannot do the changes if I have doubts because the network 192.168.0.0/22 is a the Network for the Factory Automation Systems.
I have a Nexus 7K router, has 2 ospf process, ospf 1 and ospf2. OSPF1 has several subnets in 10.1.0.0/16 subnet range , OSPF2 has several subnets in 10.2.0.0/16 subnet range. I want to summary OSPF 1 subnets to 10.1.0.0/16 then redistribute to OSPF2.but OSPF 2 didn't receive 10.1.0.0/16. Below is the config
ip prefix-list all seq 10 permit 0.0.0.0/0 le 32 route-map all permit 10 match ip address prefix-list all router ospf 1 router-id 10.10.3.9
I'm new to CiscoWorks and I inherited the system in my new job. We are running LMS 3.2 and I want to run a report to see what versions of IOS that are running on the network.
Unable to run Eos/EoL report, I get error that my cisco.com credential are not valid, I verified my credential and they work fine. I'm running RME4.3.2 on Solaris 10.
I have cisco acs 5.3 appliance. Issue is, when i view tacacs accounting it only shows 100 pages of records. So first kindly tell me if this is the limitation of acs 5.3 to only show 100 pages. Secondly if i want to export the report of last 30 days, its also not showing the last 30 days.
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
I am using LMS version 3.2 and i am not able to generate EOS/EOL report with error no connection to Cisco.Saw an update i LMS portal as this:
Now Available! LMS 3.2:Patch for un-interrupted service of Cisco.com download for Device/Software/PSIRT/EOX updates (To be applied on or before 15-June-2011)
so upgraded the patch cwcs33x-win-CSCto46927-0.zip and restarted the demeon as read in the read me file for the patch.Now the job execution status is always shows running, its neither fail nor pass.
