I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
logging enable
logging buffered 7
access-list ALL line 8 extended permit ip any any
[Code].....
i have a SMC8014WG-SI Router and its gateway is 192.168.0.1 but when i type it in the router doesn't appear at all , just says that the page cannot be found. i like portforwarding and need to be able to login the router to do so.
View 9 Replies View Relatedon IOS versions higher than 12.2(50) on Cisco 3560G-48TS I get this error/traceback, when I reach a certain number of Access-lists group'ed to "interface vlan", and the ACL inserted in the TCAM reaches acl label #128 (can be seen with : Show platform acl label 128)I can see errors in the TCAM if I issue the command
View 21 Replies View RelatedI've run in to this on 3750G's in a various sized stacks. We apply port security for a mac address on a single port (not existing on more than one port - that's a different issue that appears in multiple posts already).In this case:
1) We do a 'sho mac address-table and see that the device with the mac address in question lives on one port, port 1/0/x.
2) We apply mac port security for this exact same mac address to the same port it is already attached to. switch(config)#int g2/0/2 switch(config-if)#switchport port-security mac-address 001a.1ec8.abcd
3) Get this error: 'Found duplicate mac-address 001a.1ec8.abcd'.We again confirm that that is the only port on the entire switch that has this mac-address.Try the command again, same error.
4) We do a bunch of show commands, get in and out of the switch, go back and then try it again, and now it works, same command, same port and same mac address.
-Aging is default 300
-These are Cisco wireless AP's attached to the switch
-This occurs on different switches with different ports using different mac addresses, always same symptoms.
I have a cisco ASA 5510 runing IOS version 7.2(5).I am using asdm-647.bin file for accessing asdm. But when i do https:\<ASAIP> , it takes me to user authentication. on entering the username password it gives me the below error.The page cannot be found The page you are looking for might have been removed, had its name changed, or is temporarily unavailable. Please try the following:If you typed the page address in the Address bar, make sure that it is spelled correctly.Open the 172.16.5.3 home page, and then look for links to the information you want. Click the Back button to try another link. Click Search to look for information on the Internet. HTTP 404 - File not foundInternet Explorer not sure what the issue is. I am accessing it from the inside network. I have enabled http server and also gave inside network http access.
View 1 Replies View Relatedtyping 192.168.0.1 just times out when there no internet connection problem. I can go into my modem settings through. I don't know when this problem started as I hadn't needed to log into my router in over a year. I tried resetting it and still can not go to the log in page. I noticed a few months ago my NAT type went from open to strict on my xbox live but didn't really care at the time
View 10 Replies View RelatedSome emails that come into the INBOX are not complete and do not have graphics.On opening some emails in my Inbox, it tells me that THE WEB PAGE CANNOT BE FOUND.Some emails are going straight into the DELETED ITEMS BOX and are not SPAM. Some of them can be opened by clicking on to the LINK but others will not open.I have also had (Your email programme does not support HTML), which I do not understand.I telephoned my server and was advised to contact a PC Technician as I may have a VIRUS.
View 3 Replies View RelatedI have a WLC526 running sw version 4.2.61.8 that I finally got around to installing in my shop for testing after sitting on the shelf for several years. Since it's now out of warranty and I'm no longer certified getting the latest sw version isn't possible so I'm stuck with the version it shipped with.
1, How do we change the web log in page from https to http? No guest wants to get confronted with a certificate error page so https doesn't make sense.
2, The virtual interface used for Web-Auth provides for a DNS Name but if I set a name it won't resolve and the log in fails. If I delete the name it uses the assigned IP instead and works fine. How do I get the DNS Name to work since it looks more professional?
3, When changes are made to the WLC I was initially just applying the change and then saving the config but it appears for some of these changes to take affect I have to reboot. It this correct or am I just missing something.
Again some of these issues are probably addressed in the subsequent sw releases but since my device sat in a box for 3+ years I missed out on the opportunity to upgrade and now TAC is telling me { (no contract || no warranty == no software) }, despite the fact that this device reached its EOL.
I have a custom webauth page installed that I am using with web passthrough authentication on my WLC2006 in order to put up a acceptable use policy page. The WLC uses HTTPS to display this which causes a security certificate warning to appear if I go with the WLC's own self-signed certificate. Is there a way I can get the WLC to use plain HTTP to display this page instead so I can eliminate the warning? I have already tried installing a trusted 3rd party certificate on the WLC, but I have this very strange problem where mucking with the WLC's web authentication certificate in any manner causes all network activity on the WLC to break except for CDP and ARP, essentially leaving the WLC dead. Three weeks of troubleshooting with Cisco TAC has yielded no progress on that front so now I am trying to bypass the need for a security certificate altogether since I really don't need to encrypt my acceptable use policy page.
View 13 Replies View RelatedWhen a friend sends me an email with a link to click on when I click on ther link a blank page pops up with the words "404 not found". Why does this happen and is it a big problem. This problem just started to happen a few weeks ago. I never had a problem whenever a friend sent me an email with a link to click on.
View 6 Replies View RelatedI've had two 932Ls for a year and they work fine. Both installed trouble-free and have been used with motion-detection wirelessly. I often go straight to their local IPs in my browser to make any changes to settings etc (avoiding myDlink). I just bought two 930Ls (don't need/want the IR-function on these) and tried to install them. Process went seemingly smooth but once the camera was installed and wireless, problems started to crop up. As I saved settings in the web interface, I would get 404 "page not found" errors. Refreshing would make it work again...sometimes. More often than not, I cannot reach it through the web interface and the camera reads "disconnected" in D-ViewCam. It usually works on myDlink though. i've checked all the network and wireless settings and they are identical to my 932Ls. The connection is just unstable for some reason. The problems are apparent in the web interface and D-ViewCam which also means I can't trust the motion detection and emailing function. It is also NOT visible in my Windows 7 network environment, whereas the two 932Ls (and my entire Sonos network) do show up there.The 930L is running firmware 1.04 and the 932Ls are running 1.02. I know there is a 1.06 available but before I try that I'd like to get your views on this problem. Could it be a faulty unit? I don't want to fight through this problems - if it persists I'd rather return the cameras and buy two more expensive 932Ls and just turn off the IR in the interface. Or is this a known issue with the 1.04 firmware?
Even writing this right now, the camera suddenly popped back up on the web interface inexplicably, without me doing anything. and back up on D-View Main Console.
We have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies View RelatedThe router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
For the past week I've had a problem browsing the internet. Now, at first, this only happened starting at around 3 am central time and ending at about 6 am when I could browse the internet properly. As the days went forth, however, it began happening earlier at around 12 am. What would happen is this: would be on the internet browsing sites and whatnot. All of a sudden (As I'm loading a new page) I would get the "Address not found" error as if I'm not connected to the internet. I could try to reload any other page on my session,but sometimes it would halfway load (ei:not loading pictures, ect.) and other times I would get Address not found. This would go for about a 4 hour time period. After that, everything would be back to normal and I could go back on my session.
Now, I'm on my laptop via a router that is in my house. We also have a desktop computer, but I noticed this problem happening on my laptop first. When it first happened, it was only on my laptop. I had internet connection and could browse it endlessly on my desktop. As the days went on, however, my desktop started having the same problem connecting to the internet (I still noticed the problem on my laptop first and then I would go see if the desktop had it too).When this first happened, I was thinking my laptop wasn't connecting to my router. Instinctively, I reset the router to no avail. I also opened up IE (I don't use it much because it's just too slow) and tried to diagnose the problem using that. When I did this, it was giving me DNS as the problem of me not connecting to the internet. I am not a network admin so I don't know that much about DNS. I also used IE to diagnose the problem on the following days, but after the first time it only gave me a "You aren't connected to the internet" solution. Since then, I've been running a barrage of anti virus, rootkit, ect. just because I can and I haven't done it in a long time. I didn't find anything unusual in all the reports so I'm still not sure what the problem is.
ive just installed Cisco Prime LMS 4.1 on a Windows Server 2008 machine. when i try to open some features. like topology or the VLANs configuration options in the configuration menu i get the error HTTP STATUS -500 and this:
type Exception report
message
description The server encountered an internal error () that prevented it from fulfilling this request.
exception
javax.servlet.ServletException: Servlet execution threw an exception
[code]....
We are monitoring everyday C-2500 router, the CRC and input error are increasing day by day.This are current readings as observed on 18 Feb.
C-2500-R1#sh int s0
Serial0 is up, line protocol is up
Hardware is HD64570
[Code].....
We're getting this error message randomly when surfing the Internet. We have websense running on our network to perform web content filtering and are using the ASA for the http/https redirects. We've contacted websense and they said this error message is coming from the ASA, not their product.
ASA-5550
version 7.2.4
I am trying to generate bug summary report from RME but once job completes i can not see/view report. whenever I am trying to click on view under job result to see reports I get apache/http error. snap shot is attached for reference.
I am running LMS 3.2.1 and RME 4.3.2.. struggle alot to reach this stage where I can see report are getting generated for PSIRT and bug summary..but can not see report for Bugs though I can see PSIRT report...
I am trying to install the WLAN driver for Dell Dimension 9200C desktop computer running Windows XP but I keep getting the error that no compatible hardware was found. I've gone to the appropriate Dell Drivers site for the computer's model and I'm 99% sure I downloaded the correct software for WLAN: Dell Wireless 1395 WLAN MiniCard. After going to Device Manager and looking under "Network Adapters", there is no Dell WLAN card at all (direct ethernet connection for internet works). Is it possible that the computer cannot find the WLAN network card, which prevents me from installing the driver software, even though it exists? If so, what can I do? If not, I guess I'll go buy a USB network adapter.
View 2 Replies View Relatedi have 9 pcs on a lan. when i attempt to view the workgrp i get a message that indicates the the workgrp is not accessible and network path not found. i have tuned off windows and mcafee firewalls so that the only firewall functioning is with the modem/router(netopia) if i change the workgrp to the default(mshome) i can see the pcs.
View 2 Replies View RelatedI am facing issue with http login after IOS upgrade on 3750 switches. I upgrade IOS from c3750-ipbase-mz.122-35.SE5.bin to c3750-ipbase-mz.122-53.SE2. bin Any other command I have to run.
View 1 Replies View RelatedI have been trying to get the http server enabled so I can access Cisco Network Assistant. I have my interfaces configured but for some reason the server in not running, port 80 is still closed. [code]
View 2 Replies View RelatedI have tried search but found found anything for the 3750 switch about how to redirect HTTP, HTTPS & SMTP traffic to altenative gateway, than our standard gateway on our network, so here goes:
The network that need the HTTP, HTTPS and SMTP traffic redirect is 192.168.5.0/24 and should be redirect to 192.168.5.205 where as all other traffic need to be direct to 192.168.5.199.
Can the 3750 switch do this typo of refirect and if how?? I cannot find anything on the Cisco site stating how or even if it is possible!
I have cisco 881 and configured with http access, but when i try to open in browser it's shows blank page. Is the Cisco 881 supports GUI ?
View 3 Replies View Related2801 Router
3550 switch
3500 switch
2 2950 switches
2 pc hosts
Basically I have both PC's pinging 4.2.2.2 DNS, Layer 2, Layer 3 intervlan routing functioning, 2801 Nat is translating, able to ping default gateway of ISP and have configured DNS from what ISP has given under my DHCP scope, however Im still not getting, web pages opening up when i open mazzila or firefox !
even after installing t driver,i'm getting t same error message.Wifi adapter cannot be found
View 1 Replies View RelatedOn a Catalyst 6509 switch I have configured wccp protocol in order to redirect the Http traffic to a Bluecoat SG8100. It was working fine until a new L3 interface implementation.Thereafter I was unable to redirect the http traffic due to an error reported from the Cat6509: [code] After some checks I supposed that the problem should be the UDP 2048 port connection between the Switch and the Bluecoat while the switch L3 port and the bluecoat are on the same Lan. A deep analysis found that the WCCP protocol seems to be as follow:
-Proxy address 10.64.28.240 to Switch Port 10.64.28.250 Here I Am
-Switch Port 10.64.28.250 to Proxy address 10.64.28.240 I See You
-Switch Port 10.66.0.251 to Proxy address 10.64.28.240 UDP 2048 packet (dropped by firewall)
It's strange to me that the first dialog is correctly handled by the correct Cat6509 interface while the UDP packets are flowing from another Vlan interface not configured with the WCCP and apparently not involved on the protocol.Last of all the WCCP is now disabled and unusable?
I am trying to mark http packets from a web server with DSCP ef, but when I am doing a traffic capture all http packets have tos 0x0.I am able to mark UDP and ICMP packets originated from this server, but not any TCP traffic.The web server is in VLAN 20This is my config mls qos ip access-list extended MARK-HTTP-ACL permit tcp host 10.10.10.10 eq www. [code]
View 4 Replies View RelatedI am trying configure tacacs authentication for http in Cisco 2960 with IOS 15.0.1.SE. [code] But the device is not authenticating. It ask the credentials (user and pass) but not authenticates.
View 7 Replies View RelatedI have a fresh SR520 that I only did two things to it using CCA 3.2(1):
1. Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252
2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
I connected laptops to two ports:
1. FA0 (DHCP assigned laptop the address 192.168.75.12)
2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection.
What I am doing wrong with NAT? (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across. I THINK I see successful NAT translations in the NAT logging (also in the attachment).
I need getting access to my http server. I have a host name that I configured to point to my IPS IP address. Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]
View 5 Replies View RelatedI configured 2960S switch as http server. I'm unable to access the switch GUI with non privilege 15 user, with privilege 15 user it's working.
View 7 Replies View RelatedI can't to connect on my switch (WS-C2950G-48-EI) with Telnet or HTTP.When to connect with console, i have a error [code]
View 4 Replies View Related
