D-Link DCS-930L :: Unstable Connection / 404 Page Not Found Errors
Dec 26, 2012
I've had two 932Ls for a year and they work fine. Both installed trouble-free and have been used with motion-detection wirelessly. I often go straight to their local IPs in my browser to make any changes to settings etc (avoiding myDlink). I just bought two 930Ls (don't need/want the IR-function on these) and tried to install them. Process went seemingly smooth but once the camera was installed and wireless, problems started to crop up. As I saved settings in the web interface, I would get 404 "page not found" errors. Refreshing would make it work again...sometimes. More often than not, I cannot reach it through the web interface and the camera reads "disconnected" in D-ViewCam. It usually works on myDlink though. i've checked all the network and wireless settings and they are identical to my 932Ls. The connection is just unstable for some reason. The problems are apparent in the web interface and D-ViewCam which also means I can't trust the motion detection and emailing function. It is also NOT visible in my Windows 7 network environment, whereas the two 932Ls (and my entire Sonos network) do show up there.The 930L is running firmware 1.04 and the 932Ls are running 1.02. I know there is a 1.06 available but before I try that I'd like to get your views on this problem. Could it be a faulty unit? I don't want to fight through this problems - if it persists I'd rather return the cameras and buy two more expensive 932Ls and just turn off the IR in the interface. Or is this a known issue with the 1.04 firmware?
Even writing this right now, the camera suddenly popped back up on the web interface inexplicably, without me doing anything. and back up on D-View Main Console.
View 2 Replies
ADVERTISEMENT
Aug 31, 2012
I just brought this D-Link DCS-930L. I insert the disc and follow the instruction and select the option of without WPS and follow the step of connecting the lan cable and power point but at Step 2, after the green light, it keep prompting me that it can't find the camera. it connected to the router where there is a lan cable connected to my pc.
View 1 Replies
View Related
Jan 7, 2012
typing 192.168.0.1 just times out when there no internet connection problem. I can go into my modem settings through. I don't know when this problem started as I hadn't needed to log into my router in over a year. I tried resetting it and still can not go to the log in page. I noticed a few months ago my NAT type went from open to strict on my xbox live but didn't really care at the time
View 10 Replies
View Related
Jun 14, 2012
When a friend sends me an email with a link to click on when I click on ther link a blank page pops up with the words "404 not found". Why does this happen and is it a big problem. This problem just started to happen a few weeks ago. I never had a problem whenever a friend sent me an email with a link to click on.
View 6 Replies
View Related
Dec 1, 2011
I have a Motorola Surfboard cable modem with a Comcast account that is supposed to get "up to 15 mps". My desktop works gloriously, but my laptops and everything else hooked up to the net through my Media link Wireless N Router either run incredibly slow, or get kicked off completely.I've already had the router replaced one.
View 19 Replies
View Related
Apr 26, 2013
Region : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.3 Build 130320 Rel.39025n
ISP : PCCW Netvigator
I have upgraded to the latest firmware which solved lots of problems regarding unstable wifi connection as well as BitTorrent / P2P transfers.But I also observed that when my BT is on (Transmission for Mac) at around 50KB/s upload and download, my network latency hikes up from some 30ms to 500ms which affects a lot on web browsing or other apps requiring Internet.My BitTorrent app is showing I am merely making some 20 peers connection so I am not convinced that is an ISP problem but it's more about the router.
View 1 Replies
View Related
Jun 10, 2012
I am able to access 930L (2 cams) from wifi be it laptop,iphone or ipad but I am not able to see it through 3g.I have Huawei fibre optics broadband reuter from Starhub.Starhub is running away if ask them to fix it. Huawei never takes the call.I tried atleast 3 times 10 minutes each at 8006011450.It goes to disconnect. The lot talked about UPNP is enable in reuter but it does not work.
Now i talked to Dlink support with ticket DCX36811.They advised to load the firmware.I did it still the connection timeout is there. we have baby to monitor through iphone/android 3g.
View 2 Replies
View Related
Mar 29, 2011
I'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
View 1 Replies
View Related
Feb 17, 2012
I have 3 932ls and one 930l in a house in Massachusetts, all registered onto my dlink. All went fine.I brought 3 more 932l and one 930l to a house in Mexico. I had problem w the 932l wizard. Then I noticed that I had brought 2 different wizard discs. They were different versions, the older one could not find a Internet connection, so I could go no further. I tried the newer version of the 932l wizard, it found my Internet connection, and did installation and registered all three 932ls to my current mydlink account. All fine so far. On my mydlink account I have the three Massachusetts 932s , the one Massachusetts 930, and the three Mexico 932s.
I had forget to bring the 930L disc for the installation. Here is where the problem started. I downloaded the 930L wizard from the Dlink site, but I can't get past that first section where is says " checking active x, checking Internet, checking LAN " or something to that effect. It then says " can't find Internet connection, check your adapter, router, etc" or something to that effect. I can't go any further with that wizard. I was able to find the cam from my router and finally got that 930L interface, and did the manual as well as the automatic set-up. I can see the cam perfectly, by going to 192.168.1.101 I can log in, reset my password, did everything. I can see cam wirelessly.
The problem is that I CAN'T register it to my mydlink account, and hence can't see it on mydlink lite , etc.I can ONLY see the cam INTRANET - WISE.the 930L wizard that I downloaded is worthless. I have disabled firewall, did everything, tried an XP PC, as well as a windows 7 laptop.Is there any way to add the cam to my mydlink account ? I even tried the 932L wizard that DOES find my Internet connection, but it doesn't find my 930 at the part where I have to chase a cam to set up. If I can't add the 930L to my mydlink account, I would even be happy if I could access it from the 192.168.1. ddress, but I dont know how to set that up so that I can do that from a different network than my own. I suppose that there must be a way to get to my modem, my router and then to that 192.168.1.101 address?
View 3 Replies
View Related
Jan 17, 2013
I just got another DCS-930L. I have set these up to work wirelessly before but my question is why can't I connect it directly to my ethernet port and be able to get into the web interface by typing the default IP address without using a utility or installation software? I have tried to assign a manual IP to it but that didn't work. So here is what I want to do: Plug the camera into the ethernet port of my MacBook Pro and just view what the camera sees.
View 7 Replies
View Related
Jan 8, 2012
Or, does the data only go over the WAN connection when the camera is accessed via myDlink? I ask because I have this camera installed in my mountain home and the WAN connection is a 5GB/month Verizon USB modem. It seems to be chewing up a LOT of data.
View 2 Replies
View Related
Aug 29, 2011
I installed my camera a week ago and have since noticed every 15 minutes (only while the camera is plugged in) or so I would lose my internet connection. A message comes up at the bottom of my screen that says 'local area connection. A network cable is unplugged'. It takes 15-20 seconds for the connection to be re-established.
I called my ISP and asked if there were any settings on my router I needed to change since the camera install but they told me 'no' and I should contact tech support for the camera.
View 14 Replies
View Related
Jul 20, 2012
I'm having trouble with one of my DCS-930L cameras. I have successfully installed it and it's connected wirelessly to a Dovado router. However, after some 2 weeks the wireless connection drops and I can't connect to the camera anymore. As the camera is 350 km away I can't restart it. This happens everytime and the last time I was around the camera and indeed the camera LED was green. I restarted it by pulling the powercord and after that the camera worked for som 2-3 weeks and then the same problem again.I have 4 cameras, and it's always the same one that drops the connection and the router is only some 5 meters away from the camera. No walls between the router and the camera. I have the ability to restart the router with an sms, but that doesn't make the camera reconnect.
View 2 Replies
View Related
Jun 20, 2011
i have a SMC8014WG-SI Router and its gateway is 192.168.0.1 but when i type it in the router doesn't appear at all , just says that the page cannot be found. i like portforwarding and need to be able to login the router to do so.
View 9 Replies
View Related
Feb 19, 2011
Some emails that come into the INBOX are not complete and do not have graphics.On opening some emails in my Inbox, it tells me that THE WEB PAGE CANNOT BE FOUND.Some emails are going straight into the DELETED ITEMS BOX and are not SPAM. Some of them can be opened by clicking on to the LINK but others will not open.I have also had (Your email programme does not support HTML), which I do not understand.I telephoned my server and was advised to contact a PC Technician as I may have a VIRUS.
View 3 Replies
View Related
Jan 18, 2012
I have a cisco ASA 5510 runing IOS version 7.2(5).I am using asdm-647.bin file for accessing asdm. But when i do https:\<ASAIP> , it takes me to user authentication. on entering the username password it gives me the below error.The page cannot be found The page you are looking for might have been removed, had its name changed, or is temporarily unavailable. Please try the following:If you typed the page address in the Address bar, make sure that it is spelled correctly.Open the 172.16.5.3 home page, and then look for links to the information you want. Click the Back button to try another link. Click Search to look for information on the Internet. HTTP 404 - File not foundInternet Explorer not sure what the issue is. I am accessing it from the inside network. I have enabled http server and also gave inside network http access.
View 1 Replies
View Related
Dec 14, 2011
I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
logging enable
logging buffered 7
access-list ALL line 8 extended permit ip any any
[Code].....
View 4 Replies
View Related
Sep 26, 2010
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies
View Related
May 31, 2011
I recently moved back home with my desktop that use to be plugged in via ethernet. I bought a PCI Wireless card and I have been having problems connecting to and staying connected with the network. Once I am connected the connection speed is very slow. I have tried reinstalling windows and my card several times, even going to the store to swap it out. I have a feeling that one simple setting is changed, but I can't figure out what it is. I am currently on a laptop that is also running windows 7, but has none of the problems of the desktop. I tried to run the Netalyzer program on the desktop, however, the network disconnected as soon as I tried. Here is the link to the results from my laptop that is connected to the network: ICSI Netalyzr — Results
View 4 Replies
View Related
Jul 10, 2011
So my issue has been going on for a while now a while after I replaced the router from a DIR-535(If I recall) to a DIR-635. Now the problem resides in my computer however as it would seem that I randomly tend to loose internet acces and it only applies to my computer in the form of obviously loss of internet and the horrid warning triangel in the corner. I've tried removing and restarting the connection without any succes, I also tried to do a ipconfig /release /flushdns and /renew but it didnt seem to do anything either, basically been throwing attempts at a wall to see what works.
As far as the actual card goes it's a Atheros AR9285 Wireless Network Adapter.
View 2 Replies
View Related
Sep 1, 2011
I have recently built a new computer and now I am having trouble with my network connection. When I was done I directly connected it to my 2wire modem with the Ethernet cable.There was no connection until I downloaded the LAN driver from the CD that came with the motherboard [ASUS M5A88-V EVO ATX]. It worked for a few days and then the connection just started dropping. The trouble shoot in Windows 7 fixed it - but only for a while until it didn't work at all. Restarting the computer restored the connection and usually gave me about a few hours to work with, but a few days later all I had were a few minutes. Other than this computer I have two laptops [Windows 7] and a desktop [Windows XP] which the internet runs smoothly on when hardwired to the modem and I didn't have to install anything. Some messages I get from the trouble shoot are:LAC doesn't have valid IP configuration Default gateway not available Unidentified network?
View 2 Replies
View Related
Feb 27, 2012
I've been having big problems with my Belkin router. The connection is often slow even after restarts etc. I'm not sure whether it's the line quality/broadband usage/router quality that's causing the problem. How can I pinpoint the issue?ISP: Virgin MediaBroadband: ADSLAnti-Virus: AVGI've attached the image and ipconfig text file.
View 1 Replies
View Related
Aug 1, 2012
My laptop has a very unstable connection and I am completely stumped. I've monitored the ping and it is usually around 32-50, but it constantly spikes to 3k+ for roughly 10 seconds, it also disconnects at random intervals. I've tried updating the networking drivers, disabling firewalls and changes the preferences.
I have a Samsung Series 7 Chronos running Windows 7.
View 8 Replies
View Related
Jan 6, 2012
Since a few days I've installed my Sitecom 300N Repeater to extend the wifi signal at my home.I named my repeater the same as my wifi UPC modem (Cisco EPC3925), so the PC will see 1 connection instead of 2. I also turned off the DHCP server on the repeater (not sure what it does, but it was recommended when I was goggling around).fortunately I'm experiencing a lot of trouble. Although I can connect to the repeater, the signal is not always stable. Many times my connection speed is as low as 3 Mbps. When I quickly turn the power off and on it instantly jumps back to around 40 Mbps and stays like that for a few hours/days.It's very hard to debug this problem because after resetting the the repeater is doing very good until it slows down or even dispersers after a few hours.
View 4 Replies
View Related
Apr 3, 2013
Region : Netherlands
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 121211
ISP :
after changing from a Thomson router with wifi to the TP-link WDR-4900 I find that the wifi is very unstable. The 2.4GHz is operating on the same channel as my previous router (channel 8 - which is the lest busy channel around my house), and none of my neighbours have wifi on the 5GHz band. Almost all devices in my home regularly have to reconnect to the wifi, both on the 2.4GHz as on the 5GHz (tested with more than 8 devices). Almost every 15 minutes I see a "wifi channel disconnected" message, 10 seconds later followed by a "wifi connected" message. the Wifianalyser app on my tablet confirms that the wifi signal drops once in a while to zero. I use the latest stable frmware (I read that there is beta firmware but I don't like to loose warranty). The stability seems to unrelated to the amount of traffic on the wifi network.
Will this be fixed in the next firmware of the TP-WDR-4900 ?
View 7 Replies
View Related
Feb 2, 2011
I have a Linksys WRT110 wireless router for my desktop via a D-link DWA-125 wireless adapter. The OS is Windows 7 64 bit and I mainly go online to play games. This has been a while and every time I play games, which requires stable connection, I will get this lag (the ping goes as high as 600ms for every few seconds then goes back to normal).I tried many ways to troubleshoot and find no solutions. I updated firmware for USB adapter, power cycling the router and reset the router many times.
View 3 Replies
View Related
Dec 20, 2009
I bought the WMP600N because Linksys and Microsoft listed it as 'compatible' for Windows 7 x64. My experience:
- unstable and weak connection
- pings to websites like google.com drops, average: 1 out of 3
- low signal, on the same spot my three years old HP-laptop with 'a build in wireless card' has full signal strength in Windows 7
- it works well under Windows XP (32 bit)
I am convinced that drivers for the WMP600N are not ready for Window 7 x64. Linksys (or Ralink, which developed the chipset), release a proper driver for the WMP600N.
View 9 Replies
View Related
Nov 24, 2010
I don't know if this because buggy firmware (i updated to V1.00.16) or there something wrong with the device but if i set radio band to AUTO which enable wide-channel, my wireless connection become unstable when i ping to the modem, i got 200ms - timeout randomly
my family notebook that on other side of room connection also become more worst , ping to the modem (192.168.1.1) timeout so often
the connections seems better if i set radio band to standard - 20Mhz channel even though it seems WAG54G2 have more stable wireless connection (i replace it because the ethernet port dead) i also tried to change the channel, but the issue still persist, it seems the default is the most stable (channel 9 for wide, 11 for standard)
should i RMA the product as i just purchase last week? or it just because the bad firmware ?
View 9 Replies
View Related
Jan 26, 2013
I have had my EA2700 for about 6 months now. Have had no problems until about a month ago. One night I could not get the router to connect to the internet. First thoughts were that the cable connection had gone down. When I finally started to trouble shoot I was able to confirm the cable connection is fine by connecting to the modem directly.
Out of the modem I am getting 14+ Mbps. (I only Pay for 10 So a plus there)
I could not get the router to connect to the internet. I ended up resetting the router and reconfiguring it. Ever since then I have been getting really unstable connection to the internet.
When I connect directly to the modem (cabled) I am getting a nice steady connection . When I add the router and hardware in I get a good connection only a Mbps or 2 drop off and a pretty steady connection. Then when I connect over WIFI I get a much larger drop off depending on if the device is a 2.4 or a 5
The connection is extremely unstable. The curve on the graph {URL} is very peaky and has extreme highs and lows. This is multiplied when running on the GHz (as my laptop runs on). My Iphone running on GHz. I can pull down 9 Mbps but the curve is still up and down. Iphone on GHz I barely get Mbps and it is extremely choppy on the graph.
I am able to back this up with my I PAD. I can only confirm the 2.4 number with the laptop as it does not have GHz radio in it. So every thing that us running on the 2.4 is getting poor connections.
I also suspect that the through put on the wired side is poor as well. I am unable to prove it as every test I run shows a good connection but netflix has been locking up and I have to restart what ever I am watching 2 to even 10 times a show. I need to do more testing to be sure the network or the devices are to blame.
View 2 Replies
View Related
May 14, 2013
Just installed a refurb EA4500 this past weekend after testing it for a week. The regular wireless network is very stable, but not much faster than my single-band DLink DIR655. Guest network seems to drop out from two connected iPhones, and when the connection drops, you have to re-login and type in the guest password everytime. The linksys firmware is up-to-date( Linksys smart wifi)and so are the iOS on the 2 iPhones. Just to add, on my old DLink, the guest network comes up secured also, so when you type in the passcode, it remembers it next it comes in range unlike the Cisco, which requires login at a web interface.
View 3 Replies
View Related
Jun 15, 2012
The problem is that it always stays around 121-150mbps and sometimes 270mbps(beside router). here is my wireless settings on my router
router setting 1: [URL]
router setting 2: [URL]
network card setting:
802.11n channel width:auto
802.11n mode:Enabled
Ad-hoc channel:11
Fat channel intolerant:Disabled
Roaming aggressiveness :Medium
Throughput enhancement:Disabled
Transmit power:Highest
Wireless mode:802.11a/b/g
View 9 Replies
View Related
Sep 13, 2011
I have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
View 1 Replies
View Related
Feb 16, 2013
Region : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.0 Build 130206 Rel.34701n
ISP : PCCW Netvigator
I have bought tp-link wdr-4900 for several days and encounter the following problems
1) nfs is not work, whenever I set up the nfs server (using hanewin nfs server), the media player fails to read the media file. (Problem does not appear for the previous ASUS n56u)
2) When there is large traffic rate (e.g. BitTorrent), the whole machine is very unstable, LAN and Wireless dies (SSID disappears, and LAN appears "ERR Connection" and "DNS not respond"), give me a feeling that the router cannot handle high traffic rate and the whole machine slows down and fails.
View 14 Replies
View Related
