D-Link DCS-930L :: Wizard Won't Find Internet Connection
Feb 17, 2012
I have 3 932ls and one 930l in a house in Massachusetts, all registered onto my dlink. All went fine.I brought 3 more 932l and one 930l to a house in Mexico. I had problem w the 932l wizard. Then I noticed that I had brought 2 different wizard discs. They were different versions, the older one could not find a Internet connection, so I could go no further. I tried the newer version of the 932l wizard, it found my Internet connection, and did installation and registered all three 932ls to my current mydlink account. All fine so far. On my mydlink account I have the three Massachusetts 932s , the one Massachusetts 930, and the three Mexico 932s.
I had forget to bring the 930L disc for the installation. Here is where the problem started. I downloaded the 930L wizard from the Dlink site, but I can't get past that first section where is says " checking active x, checking Internet, checking LAN " or something to that effect. It then says " can't find Internet connection, check your adapter, router, etc" or something to that effect. I can't go any further with that wizard. I was able to find the cam from my router and finally got that 930L interface, and did the manual as well as the automatic set-up. I can see the cam perfectly, by going to 192.168.1.101 I can log in, reset my password, did everything. I can see cam wirelessly.
The problem is that I CAN'T register it to my mydlink account, and hence can't see it on mydlink lite , etc.I can ONLY see the cam INTRANET - WISE.the 930L wizard that I downloaded is worthless. I have disabled firewall, did everything, tried an XP PC, as well as a windows 7 laptop.Is there any way to add the cam to my mydlink account ? I even tried the 932L wizard that DOES find my Internet connection, but it doesn't find my 930 at the part where I have to chase a cam to set up. If I can't add the 930L to my mydlink account, I would even be happy if I could access it from the 192.168.1. ddress, but I dont know how to set that up so that I can do that from a different network than my own. I suppose that there must be a way to get to my modem, my router and then to that 192.168.1.101 address?
I installed my camera a week ago and have since noticed every 15 minutes (only while the camera is plugged in) or so I would lose my internet connection. A message comes up at the bottom of my screen that says 'local area connection. A network cable is unplugged'. It takes 15-20 seconds for the connection to be re-established.
I called my ISP and asked if there were any settings on my router I needed to change since the camera install but they told me 'no' and I should contact tech support for the camera.
I'd had my camera offline for the last couple of months, and in the interim I've upgraded both my main pc and the wireless router. I'm running Windows 7 Ultimate 64-bit on the pc, and the router is a netgear gigabit dual band wired/wireless. When running through the camera setup I am not able to get setup to find the camera, whether wired or wireless. I know that the camera's online as it shows in the routers device table, and I'm able to access the camera with my browser. However, the failed setup prevents my registering the camera on MyDlink. Any thoughts? Should I be looking at the ports on the router in regard to the camera's IP?My goal is to be able to remotely monitor my home, which the MyDlink service seemed to offer. Based on what I've read, it appears there are other ways to achieve my goal, but I would like to figure out the install problem.
When restarting my PC after a short power failure the D-Link connection wizard autostarts trying to connect to my wlan. After a short while I have a connection and is able to access the internet. The connection wizard, however does not register that a connection has been established and continues to attempt to connect for two minutes, then shuts down and immediately starts for another two-minute try....and so on. If I shut it down it just pops up again.This has never occured before. I run Windows 7 on an HP with an AMD processor.
I am able to access 930L (2 cams) from wifi be it laptop,iphone or ipad but I am not able to see it through 3g.I have Huawei fibre optics broadband reuter from Starhub.Starhub is running away if ask them to fix it. Huawei never takes the call.I tried atleast 3 times 10 minutes each at 8006011450.It goes to disconnect. The lot talked about UPNP is enable in reuter but it does not work.
Now i talked to Dlink support with ticket DCX36811.They advised to load the firmware.I did it still the connection timeout is there. we have baby to monitor through iphone/android 3g.
I'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
I just got another DCS-930L. I have set these up to work wirelessly before but my question is why can't I connect it directly to my ethernet port and be able to get into the web interface by typing the default IP address without using a utility or installation software? I have tried to assign a manual IP to it but that didn't work. So here is what I want to do: Plug the camera into the ethernet port of my MacBook Pro and just view what the camera sees.
Or, does the data only go over the WAN connection when the camera is accessed via myDlink? I ask because I have this camera installed in my mountain home and the WAN connection is a 5GB/month Verizon USB modem. It seems to be chewing up a LOT of data.
I'm having trouble with one of my DCS-930L cameras. I have successfully installed it and it's connected wirelessly to a Dovado router. However, after some 2 weeks the wireless connection drops and I can't connect to the camera anymore. As the camera is 350 km away I can't restart it. This happens everytime and the last time I was around the camera and indeed the camera LED was green. I restarted it by pulling the powercord and after that the camera worked for som 2-3 weeks and then the same problem again.I have 4 cameras, and it's always the same one that drops the connection and the router is only some 5 meters away from the camera. No walls between the router and the camera. I have the ability to restart the router with an sms, but that doesn't make the camera reconnect.
I've had two 932Ls for a year and they work fine. Both installed trouble-free and have been used with motion-detection wirelessly. I often go straight to their local IPs in my browser to make any changes to settings etc (avoiding myDlink). I just bought two 930Ls (don't need/want the IR-function on these) and tried to install them. Process went seemingly smooth but once the camera was installed and wireless, problems started to crop up. As I saved settings in the web interface, I would get 404 "page not found" errors. Refreshing would make it work again...sometimes. More often than not, I cannot reach it through the web interface and the camera reads "disconnected" in D-ViewCam. It usually works on myDlink though. i've checked all the network and wireless settings and they are identical to my 932Ls. The connection is just unstable for some reason. The problems are apparent in the web interface and D-ViewCam which also means I can't trust the motion detection and emailing function. It is also NOT visible in my Windows 7 network environment, whereas the two 932Ls (and my entire Sonos network) do show up there.The 930L is running firmware 1.04 and the 932Ls are running 1.02. I know there is a 1.06 available but before I try that I'd like to get your views on this problem. Could it be a faulty unit? I don't want to fight through this problems - if it persists I'd rather return the cameras and buy two more expensive 932Ls and just turn off the IR in the interface. Or is this a known issue with the 1.04 firmware?
Even writing this right now, the camera suddenly popped back up on the web interface inexplicably, without me doing anything. and back up on D-View Main Console.
I think I did everything per the manual, but I cannot access my camera over the internet thru [URL] website. It says that I have to check if I have enough bandwidth, or checked if my camera is not blocked by my router But I have a Dlink DIR 655 router where I have configured the Virtual server (port 80) as it is explain in the manual I also have a DHCP reservation that works fine (I can access the camera within my network) What should I do more now to finally access my camera from internet (this is for me the interest of havinf a network camera!)
just bought DCS-930L few days ago, the manual sounds so easy (but it's hard than it looks) i stuck on the setting-up, here is my problem: unable to connect to mydlink web site and there was a problem saving my settings. seems like internet connecting problem, the software just couldn't connect to internet.i have already registered, i got my device number and it couldn't be find in my device on mydlink.
I noticed my neighbors have a WEP password on their wi-fi networks but I don't with my DIR-601 router. (I thought WEP was rather insecure.) But when I logged into the router and filled in the blank password field it refused to connect and showed no way to change it. I understand there is an always-active firewall built in. Does that protect my data and doesn't need a password? I also entered the router PIN number in a field but nothing further happened when I did. Do I need to set up WPS using the Wizard?
Have a Toshiba laptop with Windows 7 Home premium.When I try to connect to a wireless connection it asks for a security key.The wireless connection is DWG85544.
I have a windows vista service pack 1 machine.I can browse the internet, download files, play songs, movies etc.But any program that attempts to auto update, or lets say I click a check for updates button on an antivirus program it tells me there is no internet connection.I can be online downloading a file and I might click spybots check for updates link and it tells me there is no internet connection.But it isn't just spybot, its everything. Everything that has some kind of built in check for updates fails.
adobe programs. windows updates. spybot superantispyware hitman pro
You name it, it doesn't see an internet connection. I can get online, download a program from the internet, install it and tell it to check for and update only to tell me there is no internet connection.I checked internet explorers connection settings to see if a virus or something had created a proxy server, nothing there.I ran ipconfig /all and checked there, nothing unusual.my windows firewall is turned off, and as far as I know I don't have any other firewalls installed.There must be something in common that all these programs must use in order to get online that is somehow messed up. Could my winsock be corrupted in such a way as to allow manual downloading but not automatic?
i was playing back the recording,when i skipped ahead, the sound disappeared. I am recording 10 hours worth everyday, most of the time i just need to skip to a certain time to see and hear what was going on,
How to add an external antenna? I'd like to mount a DCS-930L in a location (inside a metal housing) that would need the antenna to be a few inches away. Any internal layout information?
I just brought this D-Link DCS-930L. I insert the disc and follow the instruction and select the option of without WPS and follow the step of connecting the lan cable and power point but at Step 2, after the green light, it keep prompting me that it can't find the camera. it connected to the router where there is a lan cable connected to my pc.
I had to get a new router from verizon cause the old one died. so i reset the camera and wipe all the dlink software and settings. I then start fresh. i get all the way to choosing wireless and input the password. It states that there is a problem saving your settings. I tells me nothing more. I spent 4 hours on the phone with tech support and i can get it working through wired but I can't put it in my childs room wired. it worked perfectly before the router switch. funny thing is that its the same brand and model router.
I downloaded the MAC setup Utility(BETA) and it can't find the camera.The camera is connected via Ethernet-Light on the front under the lens is green (blinks sometimes)First thing I noticed wrong was the setup utility asks if the light on the side of the camera is lit green-there's no light on the side of the camera as far as I can tell. I tried unplugging the camera and hitting the reset button on the back-nothing works.
i installed cameras but want to set up for motion. I have 2 dcs 930l cameras and I can see them live i have only 2 settings live video and camera info i also downloaded the link from support.dlink.com i have a new windows 7 laptop and it keeps tryng to download java app problem is now computer keeps asking for a username and password and I have no idea what username and pw it wants as it says in the box it is unsecure
I just recently purchased the DCS-930L wireless camera, and I am trying to connect it to my Netgear router but it states that there's an error and can't connect. My itouch and laptop connects fine with the router.
Is it possible to install the D Viewcam software on a PC that is offsite (different network) as the camera and record from there? Basically the camera is home and you record from work.Can I record directly to any NAS (same network as camera) without having a PC in the middle? Or do I need a specific NAS?What about one of those external hard drives that hook up directly to a router?
I have the DCS-930L set up at home with motion detection emails. I only want it to be sending emails when I am not home, of course, but there's no way to turn off the camera through my dlink.com as far as I can tell (only an option to remove the camera, which I assume is something more drastic). Is my only choice to unplug the camera when I don't want it emailing?
I bought and hooked up my DCS-930L camera last week. Have since traveled overseas and go to Mydlink website, log-in and then it tries to install a java applet that never does install. It shows the security box where it asks me to run and then it shows another security box with a message: java.io.FileNotFoundException:C:usersmynameAppDataLocalLowSunJavaDeploymentsecurity rusted.certs(Access is denied)
I click ok and the java applet never loads. It just keeps saying Installing Java Applet.
I have a DCS-930 running successfully on my home network. Now I want to set up a DCS-932 on a different network at my mother's house in another city, so I can monitor her house from a distance. Questions:
1. After installing, will I be able to see both cameras at mydlink.com if they are on different networks? 2. Is installation any different because there are 2 networks? 3. Can I use the existing install wizard on the laptop that I used with the 1st installation or should I use my mother's PC? 4. How do I get started since the first instruction is to insert and use the CD that came with the new camera?
Basically I want to know what the install procedure is if I am using a different network but the same laptop I used with the 1st one. The laptop has a wireless connection to both networks.
