D-Link DIR-615 :: CD Broken - How To Get To Installation Wizard
Feb 23, 2011i have already installed this, but it stop working so i unplugged it, now cant find the CD
View 1 Replies
ADVERTISEMENT
Asus RT-N12B1 / Port Forwarding Broken With Installation Of Access Point?
Mar 3, 2012I recently purchased an Asus RT-N12B1. It has an external hardware switch which allows the router to operate in different modes. I put in access point mode. Then I connected an ethernet cable from a LAN port on my Verizon supplied Actiontec MI424WR-GEN2 E router to a LAN port on the access point and turned off the wireless in the router.
I have dynamic DNS setup and port forwarding setup in the router to forward from port 50000 to 192.168.1.2:22 which is a server plugged into a LAN port on the router. This is no longer working since adding the AP and disabling wireless on the primary router. how to debug?
Linksys Wireless Router :: WRT54G Setup Wizard CD And Hard Copy Quick Installation
Jun 17, 2007I've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies View RelatedD-Link DIR-601 :: Do Need To Set Up WPS Using Wizard
Jan 28, 2012I noticed my neighbors have a WEP password on their wi-fi networks but I don't with my DIR-601 router. (I thought WEP was rather insecure.) But when I logged into the router and filled in the blank password field it refused to connect and showed no way to change it. I understand there is an always-active firewall built in. Does that protect my data and doesn't need a password? I also entered the router PIN number in a field but nothing further happened when I did. Do I need to set up WPS using the Wizard?
View 3 Replies View RelatedCabling / Cards :: D-Link DWA-125 Connection Wizard Does Not Close
Oct 28, 2011When restarting my PC after a short power failure the D-Link connection wizard autostarts trying to connect to my wlan. After a short while I have a connection and is able to access the internet. The connection wizard, however does not register that a connection has been established and continues to attempt to connect for two minutes, then shuts down and immediately starts for another two-minute try....and so on. If I shut it down it just pops up again.This has never occured before. I run Windows 7 on an HP with an AMD processor.
View 3 Replies View RelatedD-Link DIR-615 :: Where To Download Quick Router Setup Wizard
Feb 19, 2013Don't have CD. Where do I download this on Dlink site?
View 3 Replies View RelatedD-Link DCS-930L :: Wizard Won't Find Internet Connection
Feb 17, 2012I have 3 932ls and one 930l in a house in Massachusetts, all registered onto my dlink. All went fine.I brought 3 more 932l and one 930l to a house in Mexico. I had problem w the 932l wizard. Then I noticed that I had brought 2 different wizard discs. They were different versions, the older one could not find a Internet connection, so I could go no further. I tried the newer version of the 932l wizard, it found my Internet connection, and did installation and registered all three 932ls to my current mydlink account. All fine so far. On my mydlink account I have the three Massachusetts 932s , the one Massachusetts 930, and the three Mexico 932s.
I had forget to bring the 930L disc for the installation. Here is where the problem started. I downloaded the 930L wizard from the Dlink site, but I can't get past that first section where is says " checking active x, checking Internet, checking LAN " or something to that effect. It then says " can't find Internet connection, check your adapter, router, etc" or something to that effect. I can't go any further with that wizard. I was able to find the cam from my router and finally got that 930L interface, and did the manual as well as the automatic set-up. I can see the cam perfectly, by going to 192.168.1.101 I can log in, reset my password, did everything. I can see cam wirelessly.
The problem is that I CAN'T register it to my mydlink account, and hence can't see it on mydlink lite , etc.I can ONLY see the cam INTRANET - WISE.the 930L wizard that I downloaded is worthless. I have disabled firewall, did everything, tried an XP PC, as well as a windows 7 laptop.Is there any way to add the cam to my mydlink account ? I even tried the 932L wizard that DOES find my Internet connection, but it doesn't find my 930 at the part where I have to chase a cam to set up. If I can't add the 930L to my mydlink account, I would even be happy if I could access it from the 192.168.1. ddress, but I dont know how to set that up so that I can do that from a different network than my own. I suppose that there must be a way to get to my modem, my router and then to that 192.168.1.101 address?
Link Between Computer And Wireless Adapter Is Broken
Aug 26, 2012I have a new wireless router (new network, entirely). I used to get intermittent "network access denied" messages. Now, I get intermittent connectivity loss: "No internet access." I typically just right click and troubleshoot. The problem is solved and I get the following message: "Problem with wireless adapter or access point." Once fixed, things go on well for a random time (never more then a day). Then, however, they just fall apart.
View 9 Replies View RelatedInstall D-Link DWL-G122 - Can't Do Setup Wizard As Cd Player Doesn't Read It
Dec 26, 2011Install my wireless adapter.i can't do the setup wizard as my cd player doesn't read it.
View 1 Replies View RelatedD-Link DIR-655 :: Multicast (IPTV) Forwarding Broken In 1.21EU And 1.31EU
May 15, 2010Upgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.
I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.
Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?
D-link Dir-655 :: Lost Installation Cd - Cannot Use Wifi?
Aug 24, 2011Is there any place I can download it so I can use my wi-fi again withot buying the installation CD?
View 2 Replies View RelatedD-Link DIR-615 :: Installation And Setup Procedure
Oct 24, 2011I bought the dir-615 today and already have issues. I don't know much about networking and have an intermediate understanding of computers in general. When I run the CD Wizard the configuration says it has detected another router and asks if I want to replace it or add the new router with it. I do not and have never had a router previously. So, for whatever reason I can't use the wizard because of this. I followed the instruction perfectly and no dice. Installing it manually is a bit above my knowledge level.
View 1 Replies View RelatedD-Link DCS-930L :: Is Installation Any Different Because There Are 2 Networks
Mar 10, 2012I have a DCS-930 running successfully on my home network. Now I want to set up a DCS-932 on a different network at my mother's house in another city, so I can monitor her house from a distance. Questions:
1. After installing, will I be able to see both cameras at mydlink.com if they are on different networks?
2. Is installation any different because there are 2 networks?
3. Can I use the existing install wizard on the laptop that I used with the 1st installation or should I use my mother's PC?
4. How do I get started since the first instruction is to insert and use the CD that came with the new camera?
Basically I want to know what the install procedure is if I am using a different network but the same laptop I used with the 1st one. The laptop has a wireless connection to both networks.
Get A Installation Disk For D-link Model Dir-601 Router?
May 29, 2012How do I install or get a installation disk for D-link model dir-601 Router
View 1 Replies View RelatedD-Link DIR-825 :: USB Printer Sharing Without Utility Installation?
Sep 17, 2012Is it possible to share a USB printer via the DIR-825 without having to install a utility? Or, do you need to install the SharePort software on each computer to share a printer?
View 1 Replies View RelatedCisco WAN :: 2951 - Installation Of 2x4 Mbps MPLS Circuit And 1x8 Mbps Ethernet Link
Feb 18, 2013Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
Add Printer Wizard Not Showing
Jan 5, 2011add printer wizard not showing in the network while sharing other printer in the network
View 1 Replies View RelatedWay To Set Up Network Without / Re-install Wizard
Jan 30, 2012I recently re-installed Vista and while attempting to set up a wired network, I can't locate the wizard.I only need to set up two PCs. Is there a way to set up a network without it or is there a way to re-install the wizard.My service is Xfinity cable internet, a net gear router (5 port 10/100 Mbps FS605 v3).My pc is a HP s3700y 32-bit, the other is a dell running XP pro. I used to have these two networked when I was with Att, but with this new service I wanted to wipe the HP clean. Now I can't find the wizard, all equipment is operating properly.Have ran several checks.
View 14 Replies View RelatedWizard Cannot Connect To Modem
Apr 14, 2011My husband moved my desktop where my netgear router is connected to and now I have a red light indicating no internet is being detected. I tried re-connecting my router by going to the netgear ip address, I got in and it says its disconnected. I went through the set up wizard to see if that would fix the problem. But it didn't connect... I typed in my DSL ID and Password but it still didn't find a connection. Then I tried again and this time I tried connecting (NOT MANUALLY) it found a connection using the generic ID and password that att gave me. I was directed to the AT&T set up website and at the end of the set up it didn't find my modem..
View 14 Replies View RelatedCisco VPN :: RV220W What To Enter For Remote WAN In VPN Wizard
Apr 8, 2011I have just received my RV220W Small Business Router and I do not understand the manual/UI wrt VPN. In the past, I had a PPTP server running behind a NAT and I used Pass Through to get external clients (Macs) to connect to my local LAN. But now I would like to use the Cisco Router's VPN capabilities to set up VPN and shut down the PPTP server in my LAN.I have a couple of fixed IP addresses that end up on this router, wit ISP-based 'technical' domain names (e.g. foo.static.isp.com) with reverse lookup, so using those, I should be able to connect to my RV220W from the outside.
View 0 Replies View RelatedCisco Firewall :: ASA 5505 / ASDM Has No VPN Wizard
Oct 1, 2012I am trying to configure a site to site ipsec vpn with 2 cisco 5505 ASA's. Unfortunately when i open up the ASDM there is no vpn wizard to start the configuration.The version of ASDM i am using from flash is 645-206.bin and the firmware on the ASA's is 842-k8.bin so should be ok. Why the VPN wizard doesnt appear?
View 7 Replies View RelatedCisco Firewall :: 5505 No VPN Wizard Functionality
Sep 30, 2012I am currently looking at the suitability of replacing an 'airbreak' firewall with 2 new ASA 5505'S.One stipulation i have is that i require to connect the third party that is currently using the 'airbreak' solution using a secure iPsec VPN.I have both 5505's that were supplied by the third party, but i believe i may need a new fireware upgradeI am using ASDM 6.4.XX and the ASA's have firmware 8.4(2) and a basic licence.Am i correct in assuming that the VPN wizard functionality is missing because of th firmware installed currently on both of the ASA's? or am i looking in the wrong place?
I have done a fair amount of research an can see earlier versions of ASDM wit the VPN wizzard so can only assume it is down to the firmware.i see that the latest version for the ASA 5505's is 8.4.4 and was wondering if this will provide me with the functionality i require as it does mention in the documentation that it does support the clientless VPN options. What part number ASA5505-BUN-K9 relates too in relation to firmware for the ASA's? [code]
Cisco WAN :: 887VA-W Startup Wizard Missing?
Nov 17, 2012Ive just started up a new cisco 887va-w and the startup wizard doesnt start. Is there a way to make this manually start?
What i tend to do is run the wizard for the basic settings then run 10-15 lines from the client (depending on adsl or vdsl config) to configure the router. But for some reason this one doesnt fire it after loging on with cisco cisco to 10.10.10.1 and changed the username and password. I just get the bebased cisco cp 'basic'. Cant see anyware on it to launch the wizard either.
Ive tried reset button on the back and reset to factory from cisco cp?
Software running on the unit is c800-universalk9-mz.spa.151-4,m4.bin
Cisco VPN :: Remote Access Vpn Wizard Does Not Work Asa5505
Apr 3, 2013I have a brand new ASA 5505 running version 8.2(5). Got connected with the ASDM and ran the setup wizard and the remote access VPN wizard. I am not able to ping the outside interface from the internet, and my VPN client gets no response when trying to connect.
View 5 Replies View RelatedCisco :: 851W Initial Setup / SDM Wizard Fails
Jun 21, 2011I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
Cisco Wireless :: Can We Break Out Of Configuration Wizard 5508
Feb 14, 2013I am trying to come up with a standard way to configure controllers for my field guys. I'd like to just have them paste in a config that has all the settings, like we use to be able to do on aIOS. I am not seeing away to break out of the wizard so that they can just paste in a config. Do you have to go through the wizard in order to get to a CLI ?
View 8 Replies View RelatedCisco :: No Source Devices In Wizard To Create Collector For LMS 3.2
Dec 29, 2011I'm trying to create a LMS 3.2 IPM Collector, but no source devices appears in the wizard.I have the Auto Mode Enable in the Auto Allocation Settings, and in IPM Devices I can see all my devices. ¿
View 2 Replies View RelatedCisco Firewall :: ASDM 6.2 Configuration Tab Comes With Setup Wizard
Feb 7, 2012Everything was working fine till one day, when clicking on Configuration Button you see setup wizard prompt.It's ASDM ver:6.2 and ASA 8.2. Everything is working fine, but now unable to change any rules.
It there simple cure for that?
Ethernet Cable Not Recognized (not Broken)?
Sep 15, 2011I have searched the forums and found that there have been others with the same problem as me,but none of the solution offered was working for me so I decided to start this thread.I have an Acer laptop that wont recognize my ethernet cable, it says that there is no cable connected.
View 1 Replies View RelatedInternet Not Working / Firewall Is Broken
Jan 24, 2013I can't find the problem in firewall..
View 3 Replies View RelatedIs Wifi Broken On Toshiba Laptop
Jan 20, 2012Yesterday I was on my toshiba satelite L550-OCD and the wireless wasn't working then it started working again. I closed my laptop and when I went back to it it wasn't working again and hasn't since. It says there's no wireless connection to plug in Ethernet cable now I have tried Fn F8 and it doesn't do anything. So I went into my toshiba assist and opened optimize. Then toshiba hardware settings and clicked LAN and it says it's turned on. But when I click radar it shows it is not connected and the light is off.
View 6 Replies View RelatedInternet Port Broken On WNDR4500?
Dec 1, 2012I recently swapped a router out for an old one to check an internet problem (to rule it out basically) and when I tried swapping the newer (better) one back in it networks fine (ie computers can see/stream off each other) but it doesnt recognize as being plugged into the internet.
After doing a factory reset via routerlogin.net I still have the same problem. The only thing I can think of is maybe the port got damaged? (The ethernet cables all work fine).
My process for hooking up the new router in case I was doing something wrong:
Unplug cable modem power, swap all the cords, on router while cable modem was rebooting and then once modem connected I turn on router. Did I need to restart the PC as well? Is that why this is screwing up?
Cisco WAN :: Router 2612 Having Broken NAT
Mar 22, 2013I have a cisco router 2612 where NAT is defined ip nat inside source static tcp 192.168.1.63 80 175.x.x.x 80 extendable It appears that after sometime (may be in few hours) the NAT is broken and I no longer can access the server over port 80 externally.
View 3 Replies View Related