Add Printer Wizard Not Showing
Jan 5, 2011add printer wizard not showing in the network while sharing other printer in the network
View 1 Replies
ADVERTISEMENT
Computer Is Not Showing Printer?
Feb 2, 2011Today when I tried to add a network printer,list of browsed printers in network is shown as pc1/hplaser1, pc1/hplaser2, pc2/hplaser1, pc7/hplaser1 and so on. They are all network printers, not local printers.Then why it is not showing the printers alone, why they show the pcs in the network and the same printer is shown in different pcs as they are installed in all of them.
View 2 Replies View RelatedVista Showing Normal Wireless SSID Plus Showing Second Unidentified Network
Feb 5, 2011my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedD-Link DIR-601 :: Do Need To Set Up WPS Using Wizard
Jan 28, 2012I noticed my neighbors have a WEP password on their wi-fi networks but I don't with my DIR-601 router. (I thought WEP was rather insecure.) But when I logged into the router and filled in the blank password field it refused to connect and showed no way to change it. I understand there is an always-active firewall built in. Does that protect my data and doesn't need a password? I also entered the router PIN number in a field but nothing further happened when I did. Do I need to set up WPS using the Wizard?
View 3 Replies View RelatedWay To Set Up Network Without / Re-install Wizard
Jan 30, 2012I recently re-installed Vista and while attempting to set up a wired network, I can't locate the wizard.I only need to set up two PCs. Is there a way to set up a network without it or is there a way to re-install the wizard.My service is Xfinity cable internet, a net gear router (5 port 10/100 Mbps FS605 v3).My pc is a HP s3700y 32-bit, the other is a dell running XP pro. I used to have these two networked when I was with Att, but with this new service I wanted to wipe the HP clean. Now I can't find the wizard, all equipment is operating properly.Have ran several checks.
View 14 Replies View RelatedWizard Cannot Connect To Modem
Apr 14, 2011My husband moved my desktop where my netgear router is connected to and now I have a red light indicating no internet is being detected. I tried re-connecting my router by going to the netgear ip address, I got in and it says its disconnected. I went through the set up wizard to see if that would fix the problem. But it didn't connect... I typed in my DSL ID and Password but it still didn't find a connection. Then I tried again and this time I tried connecting (NOT MANUALLY) it found a connection using the generic ID and password that att gave me. I was directed to the AT&T set up website and at the end of the set up it didn't find my modem..
View 14 Replies View RelatedD-Link DIR-615 :: CD Broken - How To Get To Installation Wizard
Feb 23, 2011i have already installed this, but it stop working so i unplugged it, now cant find the CD
View 1 Replies View RelatedCisco VPN :: RV220W What To Enter For Remote WAN In VPN Wizard
Apr 8, 2011I have just received my RV220W Small Business Router and I do not understand the manual/UI wrt VPN. In the past, I had a PPTP server running behind a NAT and I used Pass Through to get external clients (Macs) to connect to my local LAN. But now I would like to use the Cisco Router's VPN capabilities to set up VPN and shut down the PPTP server in my LAN.I have a couple of fixed IP addresses that end up on this router, wit ISP-based 'technical' domain names (e.g. foo.static.isp.com) with reverse lookup, so using those, I should be able to connect to my RV220W from the outside.
View 0 Replies View RelatedCisco Firewall :: ASA 5505 / ASDM Has No VPN Wizard
Oct 1, 2012I am trying to configure a site to site ipsec vpn with 2 cisco 5505 ASA's. Unfortunately when i open up the ASDM there is no vpn wizard to start the configuration.The version of ASDM i am using from flash is 645-206.bin and the firmware on the ASA's is 842-k8.bin so should be ok. Why the VPN wizard doesnt appear?
View 7 Replies View RelatedCisco Firewall :: 5505 No VPN Wizard Functionality
Sep 30, 2012I am currently looking at the suitability of replacing an 'airbreak' firewall with 2 new ASA 5505'S.One stipulation i have is that i require to connect the third party that is currently using the 'airbreak' solution using a secure iPsec VPN.I have both 5505's that were supplied by the third party, but i believe i may need a new fireware upgradeI am using ASDM 6.4.XX and the ASA's have firmware 8.4(2) and a basic licence.Am i correct in assuming that the VPN wizard functionality is missing because of th firmware installed currently on both of the ASA's? or am i looking in the wrong place?
I have done a fair amount of research an can see earlier versions of ASDM wit the VPN wizzard so can only assume it is down to the firmware.i see that the latest version for the ASA 5505's is 8.4.4 and was wondering if this will provide me with the functionality i require as it does mention in the documentation that it does support the clientless VPN options. What part number ASA5505-BUN-K9 relates too in relation to firmware for the ASA's? [code]
Cisco WAN :: 887VA-W Startup Wizard Missing?
Nov 17, 2012Ive just started up a new cisco 887va-w and the startup wizard doesnt start. Is there a way to make this manually start?
What i tend to do is run the wizard for the basic settings then run 10-15 lines from the client (depending on adsl or vdsl config) to configure the router. But for some reason this one doesnt fire it after loging on with cisco cisco to 10.10.10.1 and changed the username and password. I just get the bebased cisco cp 'basic'. Cant see anyware on it to launch the wizard either.
Ive tried reset button on the back and reset to factory from cisco cp?
Software running on the unit is c800-universalk9-mz.spa.151-4,m4.bin
Cabling / Cards :: D-Link DWA-125 Connection Wizard Does Not Close
Oct 28, 2011When restarting my PC after a short power failure the D-Link connection wizard autostarts trying to connect to my wlan. After a short while I have a connection and is able to access the internet. The connection wizard, however does not register that a connection has been established and continues to attempt to connect for two minutes, then shuts down and immediately starts for another two-minute try....and so on. If I shut it down it just pops up again.This has never occured before. I run Windows 7 on an HP with an AMD processor.
View 3 Replies View RelatedD-Link DIR-615 :: Where To Download Quick Router Setup Wizard
Feb 19, 2013Don't have CD. Where do I download this on Dlink site?
View 3 Replies View RelatedD-Link DCS-930L :: Wizard Won't Find Internet Connection
Feb 17, 2012I have 3 932ls and one 930l in a house in Massachusetts, all registered onto my dlink. All went fine.I brought 3 more 932l and one 930l to a house in Mexico. I had problem w the 932l wizard. Then I noticed that I had brought 2 different wizard discs. They were different versions, the older one could not find a Internet connection, so I could go no further. I tried the newer version of the 932l wizard, it found my Internet connection, and did installation and registered all three 932ls to my current mydlink account. All fine so far. On my mydlink account I have the three Massachusetts 932s , the one Massachusetts 930, and the three Mexico 932s.
I had forget to bring the 930L disc for the installation. Here is where the problem started. I downloaded the 930L wizard from the Dlink site, but I can't get past that first section where is says " checking active x, checking Internet, checking LAN " or something to that effect. It then says " can't find Internet connection, check your adapter, router, etc" or something to that effect. I can't go any further with that wizard. I was able to find the cam from my router and finally got that 930L interface, and did the manual as well as the automatic set-up. I can see the cam perfectly, by going to 192.168.1.101 I can log in, reset my password, did everything. I can see cam wirelessly.
The problem is that I CAN'T register it to my mydlink account, and hence can't see it on mydlink lite , etc.I can ONLY see the cam INTRANET - WISE.the 930L wizard that I downloaded is worthless. I have disabled firewall, did everything, tried an XP PC, as well as a windows 7 laptop.Is there any way to add the cam to my mydlink account ? I even tried the 932L wizard that DOES find my Internet connection, but it doesn't find my 930 at the part where I have to chase a cam to set up. If I can't add the 930L to my mydlink account, I would even be happy if I could access it from the 192.168.1. ddress, but I dont know how to set that up so that I can do that from a different network than my own. I suppose that there must be a way to get to my modem, my router and then to that 192.168.1.101 address?
Cisco VPN :: Remote Access Vpn Wizard Does Not Work Asa5505
Apr 3, 2013I have a brand new ASA 5505 running version 8.2(5). Got connected with the ASDM and ran the setup wizard and the remote access VPN wizard. I am not able to ping the outside interface from the internet, and my VPN client gets no response when trying to connect.
View 5 Replies View RelatedCisco :: 851W Initial Setup / SDM Wizard Fails
Jun 21, 2011I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
Cisco Wireless :: Can We Break Out Of Configuration Wizard 5508
Feb 14, 2013I am trying to come up with a standard way to configure controllers for my field guys. I'd like to just have them paste in a config that has all the settings, like we use to be able to do on aIOS. I am not seeing away to break out of the wizard so that they can just paste in a config. Do you have to go through the wizard in order to get to a CLI ?
View 8 Replies View RelatedCisco :: No Source Devices In Wizard To Create Collector For LMS 3.2
Dec 29, 2011I'm trying to create a LMS 3.2 IPM Collector, but no source devices appears in the wizard.I have the Auto Mode Enable in the Auto Allocation Settings, and in IPM Devices I can see all my devices. ¿
View 2 Replies View RelatedCisco Firewall :: ASDM 6.2 Configuration Tab Comes With Setup Wizard
Feb 7, 2012Everything was working fine till one day, when clicking on Configuration Button you see setup wizard prompt.It's ASDM ver:6.2 and ASA 8.2. Everything is working fine, but now unable to change any rules.
It there simple cure for that?
Linksys Wireless Adapters :: WET610N Setup Wizard Disc For Mac?
Oct 10, 2009The "Setup Wizard" disc that came with my WET610N won't work in a Mac. Is there a disc or a download available?
View 6 Replies View RelatedLinksys Access Point :: Wap54g Setup Wizard 3.0 Download?
Jan 13, 2012wap54g setup wizard 3.0 download
View 1 Replies View RelatedLinksys Cable / DSL :: Wrt54g When Open Adviser It Goes To Setup Wizard
Feb 28, 2012I upgraded my router Linksys wrt54g to Linksys x2000. I was able to install the equipment with no problem, my problem is with the Linksys Advisor. When I open the adviser it goes to setup wizard, I get a screen that tells me to disconnect my old router which I have done. The next screen gives a list of routers to select from my router x2000 is not on the list. How can I get passed this screen? So I can use the adviser to set up other computers and printer.
View 1 Replies View RelatedLinksys Wireless Router :: WRT54GL Not Setting Wizard By Windows 7?
Apr 6, 2013SetupWizard fails for the WRT54GL. I'm using Windows 7. Even though the software failed the router WRT54GL seems to work.Why did the SetupWizard fail?
View 1 Replies View RelatedLinksys Wired Router :: Set Up Wizard Not Finding / Locating Befsr41?
Jan 20, 2012I just purchased a befsr41. i have wireless internet so there is no modem to plug into. when i try to setup wizard it gets all the way to checking computer staus, then at 99% it says it cannot find router. i have pinged the router following the instructions on this site and the computer found the router, but when i tryed to go to browser to go to site it won't let me on any pages. i have found that while router is plugged in i can't access internet, but the set up disc can't locate the router. why wouldn't the set up wizard find router? and i am using win 7 with xp capable.
View 3 Replies View RelatedLinksys Wireless Router :: Wrt160n To Download Install Wizard CD If Possible
Jul 24, 2012Would like to get another CD to install a wireless network for Cisco wrt160n v2 router. I have rest the router to factory default. Would prefer to download the install wizard CD if possible.
View 8 Replies View RelatedCisco Routers :: Cannot Run Service Ready Platform Wizard On SRP546
Mar 22, 2012I want change my old router to new one. I have problem with runing SERVICES READY PLATFORM WIZARD.
View 1 Replies View RelatedCisco Wireless :: Unable To Associate With WAP321 After Setup Wizard
Aug 23, 2012I just installed a WAP321. I literally configured a test SSID, implemented WPA Personal security, and could not get an iPad or Blackberry to associate with the network. The error message that appears in the Blackberry is "EAP Authentication Failed". But isn't EAP applicable only to the WPA Enterprise mode? The access point works fine if I have the test SSID without any security, but as soon as I turn on WPA Personal security, nothing can connect. Is there something really obvious I'm missing here?(When I select WPA Personal security, I have tried with just the "WPA2" version and "AES" cipher selected, as well as with check boxes ticked on both WPA/WPA2, and on both TKIP/AES. Neither works.)
View 8 Replies View RelatedCisco Infrastructure :: CCA 3.1(1) Device Setup Wizard Not Working For SR520-FE(W)?
Jan 5, 2012Steps to repeat the bug:
1) Physical Reset of SR520-FE to factory defaults
2) Run CCA 3.1(1) and connect to 192.168.75.1 using the default cisco/cisco login
3) Under the Home Menu, click the Device Setup Wizard
4) In Step 1, sellect the SR520 and observe that there is also a photograph of the SR520-FE(W) model displayed as feedback for Step 1
5) Try variations of Steps 2 through 4
Note: Step 4 has a problem because it says to plug the power into the device, but if the power was not already plugged in to begin with, we could not run the Device Setup Wizard in the first place.
6) Step 5 prompts for a user name and password.
BUG: No permutations of the documented default usernames and passwords "cisco" or "admin" work. The result is always the error dialog:Device Connectivity Status - "Failure: Not Connected.""Return to Step 1. Make sure that your PC is not connected to a network and you follow all the instructions."A search of the web indicates others are also had this unresolved issue with previous CCA releases.
Dell :: Inspiron 530 - HP D4650e - Setting Up Home Network With Wizard
Oct 17, 2011What is the best way to set up a network. Is the network wizard the way to go? Some of that terminology I dont get relative to hardware in the checklist section. I have a dell Inspiron 530, windows XP pro Sp 3 I have broadband with a westell 7500 router. I have a filtered system on all phone jacks for the signal and plugged in to the router with the phone line to the modem to the dell as primary.Peripherals are epson scanner, HP Officejet pro 8000 wireless ( i have it wired for now. thru the modem. My other PC a HP Model Pavilion d4650e with same OS. It has a linxs wireless usb adapter for Internet supply. I think I have everything I need hardware wise to proceed with the wizard.
View 2 Replies View RelatedWireless-N Gigabit Router (WRT310N) / Cannot Complete The Network Setup Wizard
Oct 2, 2011I have two PCs connected to each other through a Wireless-N Gigabit Router (WRT310N). One PC is running Windws XP while the other is running Windows 7. At this point I do not have, or want, Internet connectivity. I would, however, like to call web pages on the Windows 7 PC from the Windows XP PC. The Windows 7 PC has php files that run C++ files to analyze files supplied by the Windows XP PC and I would like to send the results of the analysis back to the XP PC.The reason for this is that I am setting up a home based web site that allows users to run programs on my Windows 7 PC but I want to keep hackers from accessing files on my Windows 7 PC. So the XP will be connected directly to the Internet and the Windows 7 PC will only be connected to the XP PC.I can successfully ping both ways between the Windows 7 PC and XP PC. So I fire up FireFox (FF) on the XP PC and type the following in the FF URL box.
[code]....
The same happens when I replace the Windows 7 PC IP address with the Windows 7 PC name.I tried to set up a network between the two PCs with the MS network wizard on the XP box. It made a setup disk with a single file on it. I was supposed to run the setup file on the other PCs that are supposed to be on the network but, whe I did, I got the following message.Cannot complete the Network Setup Wizard,An error occurred during the configuration of the network on this computer.You can configure the network manually.
Install D-Link DWL-G122 - Can't Do Setup Wizard As Cd Player Doesn't Read It
Dec 26, 2011Install my wireless adapter.i can't do the setup wizard as my cd player doesn't read it.
View 1 Replies View RelatedCisco Firewall :: ASA 5005 Default Account For Login Startup Wizard
Dec 16, 2012I am running the Startup Wizard from my browser as I do not have a Console Access for a brand new CISCO ASA and I am stucked with the User? Password ? I tried many combination and nothing worked.
View 1 Replies View RelatedCisco Firewall :: ASDM 7.1(2) / ASA5550 9.0(2) Multicontext - How To Get Remote Access To VPN Wizard
Mar 29, 2013I have the latest ASDM 7.1(2) & ASA5550 9.0(2). When I try to start Remote Access VPN Wizard, it's just nothing to select in Wizards-VPN Wizards, except "Site-toSite VPN Wizard..."
View 2 Replies View Related