D-Link DIR-615 :: Installation And Setup Procedure
Oct 24, 2011
I bought the dir-615 today and already have issues. I don't know much about networking and have an intermediate understanding of computers in general. When I run the CD Wizard the configuration says it has detected another router and asks if I want to replace it or add the new router with it. I do not and have never had a router previously. So, for whatever reason I can't use the wizard because of this. I followed the instruction perfectly and no dice. Installing it manually is a bit above my knowledge level.
View 1 Replies
ADVERTISEMENT
Nov 19, 2010
Have a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies
View Related
Jun 17, 2007
I've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies
View Related
Aug 24, 2011
Is there any place I can download it so I can use my wi-fi again withot buying the installation CD?
View 2 Replies
View Related
Feb 23, 2011
i have already installed this, but it stop working so i unplugged it, now cant find the CD
View 1 Replies
View Related
Mar 10, 2012
I have a DCS-930 running successfully on my home network. Now I want to set up a DCS-932 on a different network at my mother's house in another city, so I can monitor her house from a distance. Questions:
1. After installing, will I be able to see both cameras at mydlink.com if they are on different networks?
2. Is installation any different because there are 2 networks?
3. Can I use the existing install wizard on the laptop that I used with the 1st installation or should I use my mother's PC?
4. How do I get started since the first instruction is to insert and use the CD that came with the new camera?
Basically I want to know what the install procedure is if I am using a different network but the same laptop I used with the 1st one. The laptop has a wireless connection to both networks.
View 3 Replies
View Related
May 29, 2012
How do I install or get a installation disk for D-link model dir-601 Router
View 1 Replies
View Related
Sep 17, 2012
Is it possible to share a USB printer via the DIR-825 without having to install a utility? Or, do you need to install the SharePort software on each computer to share a printer?
View 1 Replies
View Related
Feb 18, 2013
Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
View 1 Replies
View Related
Mar 26, 2013
Why isn't a GUI upgrade possible instead of CLI initiated upgrade?Is this (GUI) only for patch upgrades or is it a valid upgrade path to use the Cisco Prime's GUI (Administarion; Software Update) in order to upload update file. Check for updates gives no results though successful login to [URL].
View 3 Replies
View Related
Oct 20, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 1 Replies
View Related
Mar 17, 2011
We have ASA 5540. After setting up one-to-one nat, do I need to do anything else? static (Inside,Outside) public ip address private ip address netmask 255.255.255.255.
View 4 Replies
View Related
Dec 20, 2010
checked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies
View Related
Jan 11, 2012
I have to migrate two appliances ACS SE 1112 under 4.0.1 to new two appliances ACS SE 1121 under 5.2 version.I would like to clarify the procedure to do it by minimizing down time impact.I saw there are Migration Utility and Import Tool but do I need an Intermediate Windows Server to do this migration ?
View 1 Replies
View Related
Oct 17, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 2 Replies
View Related
May 4, 2011
procedure to apply the 5-2-0-26-4.tar.gpg patch. I don't know how to get the patch file into the ACS server.The procedure in the "Read me" for the patch does not indicate anything about how to this:
1. open CLI console2. define new repository in which the 5-2-0-26-4.tar.gpg resides3. issue: 'acs patch install 5-2-0-26-4.tar.gpg repository YOUR_REPOSITORY'4. verify installation by getting the following version information via CLI by issuing:#show application version acs I don't know how to put the patch file from my local machine to the repository created in the GUI (if there is where the actual place to creat the repository).
View 3 Replies
View Related
May 2, 2012
From PEC training - Cisco says to perform a proper ASR 1004 shutdown by executing 'reload' , then wait for bootstrap message to appear, then [before commencement of unpacking of the IOS] turn off the power switch. IS THIS ACCURATE. Anyone have any doc related to the recommended POWER DOWN process on the ASR 1004. We have a UPS cutover coming up and I want to be ready to power down and restart the new ASR 1004s we have - properly.
View 3 Replies
View Related
Oct 30, 2011
our company is going to change its´ ISP. The External Isp are going to obviously change too. We have an Active/Standby Firewall and we would like to make the change with at least connectivity downfall as possible. In our configuration we have nearly all features configured as in a normal Productive Firwall such as , NAT, Site-to Site VPN, Remote Access Webvpn, ACLs and also routing. I have looked up some information in this community and still I am not sure about the steps to be made so to reach our goal.
I have read that changing only the "names" from the old IP Range to the new Ip range would not really make the change. The old Ip range will still be configured in the features using the external Ip address. Therefore we have to first delete all the information (in the running config) connected to these Variables and then re insert them. My biggest worry is that this could be a little bit tricky during the implementation, if some config lines or objects could be left out during the deleting and inserting procedure.
How we could make this change with a low percentage of "copy and paste failures"? I was thinking about in changing the "names" to their new Ips and then afterwards reload the ASA. Will this workout? Primary ASA will be changed first with the secondary shutdown. ASA Firmware 8.2.2 (12).
View 4 Replies
View Related
Dec 3, 2011
we purchase only Cisco Supervisor Engine VS-S720-10G and use it in our old C6509-E chassis.Now the supervisor engine was dead,(means not working and no LED's are ON). How can i claim the RMA from cisco?
We purchase from one of our partner. We send it to them,they are not able to find the Serial number from the Supervisor Engine module (Because lot of serial numbers are on the board). Also the customer through the catoon.
Now how we can know which is exact serial number of sup? How to get RMA from the Cisco on which serial number?
View 4 Replies
View Related
Jan 11, 2011
what is the set up procedure for adding a printer with wifi capabilities?
View 1 Replies
View Related
Aug 8, 2011
Point to point wireless connectivity configuration procedure using 1410 bridges either using GUI/CLI .
We have setup this in one of our Client sites.
View 1 Replies
View Related
Jan 25, 2012
I would like to discuss another method of a bulk controller upgrade and see what other engineers take on this upgrade path would be.Say I have an instance of 84404s with 50 APs each, In this case I have N+1 redundancy where I can follow the normal procedure.Normal Procedure.Move all APs to controllers 1-4Preload all APs with the new code versionUpgrade and reboot empty controllers 5-8 to new code versionMove all APs to 5-8 with new code versoinUpgrade empty 1-4Move all APs back home.Now take the same scenario only chage it to 80 APs per controller. I've now lost my N+1 and cannot do it quite as smoothly. As opposed to trying to follow the normal proceedure and have an extended window of "brown outs" How about doing it all at once.Black-out accelerated proceedure:Preload new code on all controllersPreload new image on all APs on all controllersReboot all 8 controllers at the same time.Allow time for APs to connect back and load the new image.I assume with this proceedure that I might see around 15-30 minutes of actual downtime to the site but it seems like that could be preferable to two-three hours of brown outs.
View 6 Replies
View Related
Feb 20, 2012
Am setting up Cisco 3750 for the first time via CLI
1. what is the procedure for configuring passwords on the device.
2. how can i stack 3 switches in a site .
View 1 Replies
View Related
Apr 18, 2013
I am upgrading a Cisco 6506E VSS from 12.2(33)SXI5 to 12.2(33)SXJ5 during a maintenance window. So I have plenty of time to reboot the VSS. Confirm below is the correct procedure. I have manually copied the new IOS to both active and standby Sup720s.
no boot system
boot system flash sup-bootdisk:NEW_IOS.bin
boot system flash sup-bootdisk:OLD_IOS.bin
!
copy run start
reload
I was going through the below cisco document and there are a few more steps as below: Is it necessary?
[URL]
Router(config)# no boot system
View 2 Replies
View Related
Apr 27, 2011
My bussines have an old PIX 515e and im about to install it in a "testing" eviorment but no one can remeber the password for this old equipment. Is there a way to reset the password?
But when it reboots and I write "enable" in the console it asks for a password, and the password isn't "cisco" as factory default. I really need this firewall up and runing ASAP.
How to reset the "enable"-password?
View 3 Replies
View Related
Jan 6, 2012
I'll be upgrading an HA pair of ASA 5520s next week, and wanted to clarify the procedure. I read "Upgrading an Active/Standby Failover Configuration" at [URL] which suggests placing the image on both units, updating boot statements, then issuing failover reload-standby. But I was wondering if there's a way to a way to be a bit safer. I'd like to modify the standby unit, without affecting the config on the active. So I'd like to modify the boot statement on the standby without modifying the active config. That way incase there's a problem and the active reboots, it won't upgrade.
Can I modify the config on the standby without affecting the active? Then I'd like to test the newly upgraded unit with our production traffic. Would that simply be no failover active, and then once the standby becomes active -- test traffic? Once everything is okay, I would upgrade the second unit, and fail traffic back.
View 3 Replies
View Related
Nov 28, 2011
I have Sony DR-BT100X Bluetooth headset. How to connect the BT Headset with Windows XP Laptop. My Headset is paired with my Laptop but not able to hear the sound through Headset.
View 1 Replies
View Related
Jun 27, 2011
What is the remedy/procedure to make a deformed CAT-5 cable into normal condition.
View 1 Replies
View Related
Apr 7, 2012
i just wanna know if it's possible to perform a router password recovery using the reload command and then issue the break sequence instead of doing an off/on on the power switch. i often find in the docs to use the latter.also, is there a way to retain the startup-config on a router when we re-enable the password recovery functionality (no service password-recovery). i've just tried this on one of our 877 and when i hit the break sequence, it went back to factory default setting.
View 7 Replies
View Related
Oct 15, 2012
Is there any shut down proceedure for cisco devices in data center cisco router,switches,firewalls ASA-5580-20,ace-4710 and IPS-4260 devices.
View 4 Replies
View Related
Apr 23, 2013
I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
View 2 Replies
View Related
Apr 10, 2012
i just received a RMA for failed ASA 5520 that was acting as secondary unit in multicontext configuration. What would be correct procedure to install it back in production? Do i need to restore backed up config of the fallen unit or is it just enough to enable multimode and connect to existing (primary) unit? Any good link for documentation that deal with this issues.
View 5 Replies
View Related
Oct 17, 2012
I would like to ask, given that i got 2 units of ISE-3315 appliance, one need to be primary node for admin-policy service-monitoring, another unit then become Inline posture node.For the preparation on line posture node, what shoud i do on it?
01. For the unit ready to become inline posture node, so I just boot it, install the OS from sractch (using version 1.1.1), then start the initialize setup etc, like Normal setup?
02. Before i regieter, what is the deployment nodes i should select for inline posture node unit? provided the admin-policy service-monitoring will become primary node, and registration for inline posture node will be next action.
View 10 Replies
View Related
