Cisco Switching/Routing :: Need To Know RMA Procedure VS S720
Dec 3, 2011
we purchase only Cisco Supervisor Engine VS-S720-10G and use it in our old C6509-E chassis.Now the supervisor engine was dead,(means not working and no LED's are ON). How can i claim the RMA from cisco?
We purchase from one of our partner. We send it to them,they are not able to find the Serial number from the Supervisor Engine module (Because lot of serial numbers are on the board). Also the customer through the catoon.
Now how we can know which is exact serial number of sup? How to get RMA from the Cisco on which serial number?
View 4 Replies
ADVERTISEMENT
Feb 7, 2012
We are upgrading two standalone 6509E chassis to a VSS system with new VS-S720-10G-3C cards. The 6509's have WS-X6748-GE-TX card with DFC3B daughter cards (see below). The compatablity matrix (see below) states that 67xx cards are supported but it goes on to state DFC3C or DFC3CXL cards are needed. So does this mean that the existing WS-X6748-GE-TX cards have to be upgraded or will they be supported?
Core #1Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL 2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAD 5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL 6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL 7 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL 8 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL
[code]....
View 3 Replies
View Related
Oct 26, 2011
I got a new VS-S720-10G it had 122-33.SXH8b on there. I had to downgrade it to 12.2.33.SXI1 to match our other switches. I installed the file I use in all the other switches, s72033-adventerprisek9_wan-mz.122-33.SXI1.bin but the Sup is now is only booting up only to ROMMON mode.
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : #################################################
################################################################################
################################################################ [OK]
%SYSTEM-1-INITFAIL: Network boot is not supported.
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code]....
How do I get the older version of IOS to load up?
View 5 Replies
View Related
Jan 22, 2013
We have 7 interfaces with rj45 connections.. all around 100Mbit per connection .. most likely in the future we will need a couple more interfaces.. i was thinking it would be better to take a WS-X6516-GE-TX card then a FE card as for example a WS-X6148-RJ-45 .Now we want to implement a 7606 with a SUP720-3BXL with 1GB dram for the RP(MSFC3)... so enough memory to support the 2x a FULL BGP table to two peers.
Q : Does the SUP720-3BXL work well with two peers sending the FULL BGP table ?
Q : And does that also work with a WS-X6516-GE-TX connected to the two peers sending the FULL BGP table ? .. or is it better to take a 6724 linecard with a DFC3-BXL so that the 6724 will lookup routes locally instead a 6516 will have the S720- perform the routing ? I know that adding the DFC's increases the bandwidth of the chassis significantly (40gbps per slot most 6700 linecards ,and 20gbps for the 6724 which is 1:2 oversubscribed )
Q: Or is it better to connect the two peers to the two SFP interfaces on the SUP720 , and connect the small routers and customer networks to the 6516 linecard?
View 5 Replies
View Related
Sep 9, 2009
I need those two stencils.I have checked here [URL] but:
- the one for the C6509-E is not there
- the one for the supervisor does not work properly (misaligned anchor points).
View 2 Replies
View Related
Jun 9, 2013
I'm trying to configure a egress netflow in a 6500 (VSS) with VS-S720-10G supervisor. I foud some old posts and understood that netflow wasn't supported on 6500 but i found a new document and it seems that netflow is supported in Supervisor Engine 2T:[URL] Does the netflow still not supported in VS-S720-10G? It's weird because the command is supported:
#sh run int vlan 4
Building configuration...
Current configuration : 353 bytes
!
interface Vlan4
ip address X.X.X.X 255.255.0.0
[cod]....
View 1 Replies
View Related
Jan 19, 2012
What key sequence to go into ROMMON mode from the console port for VSS system with 2 VS-S720-10G?
View 3 Replies
View Related
Jan 24, 2012
I have catalyst 6500s with two VS-S720-10Gs, one is in Active and one is in Hot state. Both Sup cards have two 10G uplink ports. How does the traffic forwarding works in this case on the uplink ports? Do these uplink ports actively forward traffic or it is only the uplinks ports on Active that forward traffic? I see CDP neighbors on both Active and Hot SUPs uplinks ports - it indicates that packets are flowing on both cards.
I want all uplink ports on both SUPs to actively forward traffic. Does it work? What is the config for this?
View 1 Replies
View Related
Apr 18, 2013
I am upgrading a Cisco 6506E VSS from 12.2(33)SXI5 to 12.2(33)SXJ5 during a maintenance window. So I have plenty of time to reboot the VSS. Confirm below is the correct procedure. I have manually copied the new IOS to both active and standby Sup720s.
no boot system
boot system flash sup-bootdisk:NEW_IOS.bin
boot system flash sup-bootdisk:OLD_IOS.bin
!
copy run start
reload
I was going through the below cisco document and there are a few more steps as below: Is it necessary?
[URL]
Router(config)# no boot system
View 2 Replies
View Related
Apr 7, 2012
i just wanna know if it's possible to perform a router password recovery using the reload command and then issue the break sequence instead of doing an off/on on the power switch. i often find in the docs to use the latter.also, is there a way to retain the startup-config on a router when we re-enable the password recovery functionality (no service password-recovery). i've just tried this on one of our 877 and when i hit the break sequence, it went back to factory default setting.
View 7 Replies
View Related
Oct 15, 2012
Is there any shut down proceedure for cisco devices in data center cisco router,switches,firewalls ASA-5580-20,ace-4710 and IPS-4260 devices.
View 4 Replies
View Related
Apr 23, 2013
I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
View 2 Replies
View Related
Nov 16, 2011
We need to change the Channel-group settings in 3750 switch from Mode ON to Mode Active. We have tried once by removing the physical interfaces from the port-channel group but we lost the connectivity to the secondary switch. Any step by step procedure without losing the connectivity between switches.
View 2 Replies
View Related
Sep 12, 2012
I need to upgrade the IOS and therefore change the flashcard on a router 2811.
What is the procedure to change the flash (64MB to 256MB) on a 2811 router?
I can remove the flashcard when the router has already started, change the flashcard and load the new IOS?
View 3 Replies
View Related
Nov 5, 2012
I am pretty far out of my comfort zone here but these VS-S720-10G-3C cards were purchased to upgrade our 7609/7606 routers, the spec sheet says they are compatable but I can't find an IOS that "likes" them. I had no problem finding an IOS and using the vss cards in our 6506...
[URL]
View 3 Replies
View Related
May 8, 2011
I'm planning to implement a VSS system with two 6509 and VS-S720-10G supervisor engines. In technical specifications is said that this card can support up to 1024 VRFs. Is this limit the same when working in VSS?
View 6 Replies
View Related
Jun 26, 2012
I am about to replace the supervisor engine in our pair of distribution switches in our data center. We currently have a FWSM module installed in each of my distribution switches running 3.1(20) code. The old sup720 are running 8.6(4) and the mfsc are running 12.2(17d)SXB11a. I am wondering about the compatibility of running the FWSM with the same code after installing the new VS-S720 modules. I do not plan on configuring virtual switch yet and did plan on upgrading the FWSM to 4 code train but just not immediately. Will I be able to run my FWSM using the current 3.1(20) code after I install my new VS-S720 running in native mode?
If I have to upgrade the FWSM then I need to know if I have to upgrade the module in each distribution switch at the same time? Furthermore I do not believe that the FWSM 4 code is supported in hybrid mode, which means that I will have to convert to native before upgrading to FWSM 4 before I install the VS-S720 in one of my distribution switches. Currently the FWSM modules are in active/standby mode in different chassis.
I had planned to install the VS-S720 module in one of my distribution switch and do the other installation a week later. I would rather not have to convert to native and upgrade the FWSM modules in both distribution switches during the first switch upgrade.
cnDS02> (enable) sh mod
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 16 1000BaseX Ethernet WS-X6516A-GBIC no ok
2 .... Please refer to Detail Note. cnDS02> (enable) sh mod
[code]....
View 1 Replies
View Related
Mar 26, 2013
Why isn't a GUI upgrade possible instead of CLI initiated upgrade?Is this (GUI) only for patch upgrades or is it a valid upgrade path to use the Cisco Prime's GUI (Administarion; Software Update) in order to upload update file. Check for updates gives no results though successful login to [URL].
View 3 Replies
View Related
Oct 20, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 1 Replies
View Related
Mar 17, 2011
We have ASA 5540. After setting up one-to-one nat, do I need to do anything else? static (Inside,Outside) public ip address private ip address netmask 255.255.255.255.
View 4 Replies
View Related
Dec 20, 2010
checked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies
View Related
Oct 17, 2011
where I can find a CLI password recovery procedure for the administrator account?
View 2 Replies
View Related
May 4, 2011
procedure to apply the 5-2-0-26-4.tar.gpg patch. I don't know how to get the patch file into the ACS server.The procedure in the "Read me" for the patch does not indicate anything about how to this:
1. open CLI console2. define new repository in which the 5-2-0-26-4.tar.gpg resides3. issue: 'acs patch install 5-2-0-26-4.tar.gpg repository YOUR_REPOSITORY'4. verify installation by getting the following version information via CLI by issuing:#show application version acs I don't know how to put the patch file from my local machine to the repository created in the GUI (if there is where the actual place to creat the repository).
View 3 Replies
View Related
May 2, 2012
From PEC training - Cisco says to perform a proper ASR 1004 shutdown by executing 'reload' , then wait for bootstrap message to appear, then [before commencement of unpacking of the IOS] turn off the power switch. IS THIS ACCURATE. Anyone have any doc related to the recommended POWER DOWN process on the ASR 1004. We have a UPS cutover coming up and I want to be ready to power down and restart the new ASR 1004s we have - properly.
View 3 Replies
View Related
Oct 30, 2011
our company is going to change its´ ISP. The External Isp are going to obviously change too. We have an Active/Standby Firewall and we would like to make the change with at least connectivity downfall as possible. In our configuration we have nearly all features configured as in a normal Productive Firwall such as , NAT, Site-to Site VPN, Remote Access Webvpn, ACLs and also routing. I have looked up some information in this community and still I am not sure about the steps to be made so to reach our goal.
I have read that changing only the "names" from the old IP Range to the new Ip range would not really make the change. The old Ip range will still be configured in the features using the external Ip address. Therefore we have to first delete all the information (in the running config) connected to these Variables and then re insert them. My biggest worry is that this could be a little bit tricky during the implementation, if some config lines or objects could be left out during the deleting and inserting procedure.
How we could make this change with a low percentage of "copy and paste failures"? I was thinking about in changing the "names" to their new Ips and then afterwards reload the ASA. Will this workout? Primary ASA will be changed first with the secondary shutdown. ASA Firmware 8.2.2 (12).
View 4 Replies
View Related
Oct 24, 2011
I bought the dir-615 today and already have issues. I don't know much about networking and have an intermediate understanding of computers in general. When I run the CD Wizard the configuration says it has detected another router and asks if I want to replace it or add the new router with it. I do not and have never had a router previously. So, for whatever reason I can't use the wizard because of this. I followed the instruction perfectly and no dice. Installing it manually is a bit above my knowledge level.
View 1 Replies
View Related
Aug 8, 2011
Point to point wireless connectivity configuration procedure using 1410 bridges either using GUI/CLI .
We have setup this in one of our Client sites.
View 1 Replies
View Related
Jan 25, 2012
I would like to discuss another method of a bulk controller upgrade and see what other engineers take on this upgrade path would be.Say I have an instance of 84404s with 50 APs each, In this case I have N+1 redundancy where I can follow the normal procedure.Normal Procedure.Move all APs to controllers 1-4Preload all APs with the new code versionUpgrade and reboot empty controllers 5-8 to new code versionMove all APs to 5-8 with new code versoinUpgrade empty 1-4Move all APs back home.Now take the same scenario only chage it to 80 APs per controller. I've now lost my N+1 and cannot do it quite as smoothly. As opposed to trying to follow the normal proceedure and have an extended window of "brown outs" How about doing it all at once.Black-out accelerated proceedure:Preload new code on all controllersPreload new image on all APs on all controllersReboot all 8 controllers at the same time.Allow time for APs to connect back and load the new image.I assume with this proceedure that I might see around 15-30 minutes of actual downtime to the site but it seems like that could be preferable to two-three hours of brown outs.
View 6 Replies
View Related
Feb 20, 2012
Am setting up Cisco 3750 for the first time via CLI
1. what is the procedure for configuring passwords on the device.
2. how can i stack 3 switches in a site .
View 1 Replies
View Related
Nov 19, 2010
Have a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies
View Related
Apr 27, 2011
My bussines have an old PIX 515e and im about to install it in a "testing" eviorment but no one can remeber the password for this old equipment. Is there a way to reset the password?
But when it reboots and I write "enable" in the console it asks for a password, and the password isn't "cisco" as factory default. I really need this firewall up and runing ASAP.
How to reset the "enable"-password?
View 3 Replies
View Related
Jan 6, 2012
I'll be upgrading an HA pair of ASA 5520s next week, and wanted to clarify the procedure. I read "Upgrading an Active/Standby Failover Configuration" at [URL] which suggests placing the image on both units, updating boot statements, then issuing failover reload-standby. But I was wondering if there's a way to a way to be a bit safer. I'd like to modify the standby unit, without affecting the config on the active. So I'd like to modify the boot statement on the standby without modifying the active config. That way incase there's a problem and the active reboots, it won't upgrade.
Can I modify the config on the standby without affecting the active? Then I'd like to test the newly upgraded unit with our production traffic. Would that simply be no failover active, and then once the standby becomes active -- test traffic? Once everything is okay, I would upgrade the second unit, and fail traffic back.
View 3 Replies
View Related
Jan 11, 2012
I have to migrate two appliances ACS SE 1112 under 4.0.1 to new two appliances ACS SE 1121 under 5.2 version.I would like to clarify the procedure to do it by minimizing down time impact.I saw there are Migration Utility and Import Tool but do I need an Intermediate Windows Server to do this migration ?
View 1 Replies
View Related
