TP-Link Dual-Band Wireless :: WDR-4900 When There Is Large Traffic Rate Whole Machine Is Very Unstable

Feb 16, 2013

Region : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.0 Build 130206 Rel.34701n
ISP : PCCW Netvigator

I have bought tp-link wdr-4900 for several days and encounter the following problems

1) nfs is not work, whenever I set up the nfs server (using hanewin nfs server), the media player fails to read the media file. (Problem does not appear for the previous ASUS n56u)

2) When there is large traffic rate (e.g. BitTorrent), the whole machine is very unstable, LAN and Wireless dies (SSID disappears, and LAN appears "ERR Connection" and "DNS not respond"), give me a feeling that the router cannot handle high traffic rate and the whole machine slows down and fails.

View 14 Replies


ADVERTISEMENT

Tp-link Dual-band Wireless :: Wifi Unstable On Tl-wdr4900?

Apr 3, 2013

Region : Netherlands
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 121211
ISP :

after changing from a Thomson router with wifi to the TP-link WDR-4900 I find that the wifi is very unstable. The 2.4GHz is operating on the same channel as my previous router (channel 8 - which is the lest busy channel around my house), and none of my neighbours have wifi on the 5GHz band. Almost all devices in my home regularly have to reconnect to the wifi, both on the 2.4GHz as on the 5GHz (tested with more than 8 devices). Almost every 15 minutes I see a "wifi channel disconnected" message, 10 seconds later followed by a "wifi connected" message. the Wifianalyser app on my tablet confirms that the wifi signal drops once in a while to zero. I use the latest stable frmware (I read that there is beta firmware but I don't like to loose warranty). The stability seems to unrelated to the amount of traffic on the wifi network.

Will this be fixed in the next firmware of the TP-WDR-4900 ?

View 7 Replies View Related

TP-Link Dual-Band Wireless :: Wdr4300 V1 When Update To Latest Firmware It Became Unstable / Disconnecting

Jan 14, 2013

Region : Iraq
Model : TL-WDR4300
Hardware Version : V1

have TL-WDR4300 router hardware v1 but when update to the latest firmware it became unstable and disconnecting so I had to return back to older firmware the new firm ware released 12/25/2012 and it is noted for TL-WDR4300(UN) V1 my model is TL-WDR4300 V1 not (UN) so what is different between the two

View 4 Replies View Related

Tp-link Dual-band Wireless :: Tl-wdr4900 Unstable Wifi Connection As Well As Bittorrent / P2p Transfers

Apr 26, 2013

Region : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.3 Build 130320 Rel.39025n
ISP : PCCW Netvigator

I have upgraded to the latest firmware which solved lots of problems regarding unstable wifi connection as well as BitTorrent / P2P transfers.But I also observed that when my BT is on (Transmission for Mac) at around 50KB/s upload and download, my network latency hikes up from some 30ms to 500ms which affects a lot on web browsing or other apps requiring Internet.My BitTorrent app is showing I am merely making some 20 peers connection so I am not convinced that is an ISP problem but it's more about the router.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR3600 / UPnP Traffic When UPnP Is Off?

Jan 24, 2013

Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider

It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: DHCP Not Working For 6 GHz Band?

Apr 2, 2013

Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink

I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: VOIP Dropped Calls Over TP-Link WDR4300

Feb 14, 2013

Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast

I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.

View 7 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 2.4 Ghz Is Not Working

Dec 31, 2012

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast

I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.

View 14 Replies View Related

TP-Link Dual-Band Wireless :: NFS Is Very Slow With WDR3600?

Feb 18, 2013

Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :

I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?

View 2 Replies View Related

TP-Link Dual-Band Wireless :: WDR7500 No Internet On 5 GHz

Mar 29, 2013

Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast

The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: Does WNR4300 Support With DD-WRT

Nov 15, 2012

Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Newroz Telecom

Can I replace firmawre TP-Link WDR4300 to DD-WRT to use it?, either my TP-link already has VPN,NAT,QOS,..etc like as DD-WRT so does need to replace firmware for better?

Does TP-Link WDR4300 support with DD-wrt? Is it working clearly without any problem?

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 Get GMT Not Working

Jan 6, 2013

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : latest
ISP : Clear

Get GMT throws an error. I set known good public NTP servers, still get error. Also power cycling or rebooting the router seems to drop manual time settings, as well. I am using WDR4300 as a wireless access point, does that matter? Maybe I don't need time in access mode? It is connected to the Internet and is providing internet access to clients.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - 2.4 GHz Signal

Mar 28, 2013

Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :

I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?

View 2 Replies View Related

TP-Link Dual-Band Wireless :: TL-WR2543ND / USB External HDD Not Recognized

Mar 30, 2013

Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :

ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:

1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.

2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.

3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.

What I can conclude from those tests is that:

1) My External HDD is working normally;

2) The router's USB port is working properly;

3) So, if both are working, it can only be a matter of compatibility between them.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - How To Get Full 450Mbps

Jan 14, 2013

Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : plusnet

How do I get the full 450 Mbps out of my router on the status it saying 300Mbps

View 5 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 WDS Bridging Not Working

Nov 21, 2012

Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
Region : Others

I have Enable WDS Bridging and run Survey which detect the other SSID to be joined with the correct MAC address.I had filled the password of my second THOMSON v 585 V7 with the correct Auth Type both routers broadcast on channel 11.But my TP-Link 2543ND cannot made it work.I also disable DHCP and changed my LAN ip to 192.168.1.2 and can access it over my lan.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 / Can't Access Usb Storage

Mar 5, 2013

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

The router is working and when I plug in an external drive to usb I can see in the admin tool. It is setup to share without a password. I am using a PC with Vista on it...so I go to RUN and enter [URL] but I get the following message:'Windows cannot access [URL]

View 2 Replies View Related

TP-Link Dual-Band Wireless :: Interface Of TL-WDR4300 Is Slow

Feb 11, 2013

Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121225
ISP : Online

Recently I replaced my Linksys WRT54G for a TP-Link WDR4300. But unfortunately this did not result in an increased speed.On both the 5GHz and 2.4GHz speed is limited to roughly 2.5-3 MByte/s, which is OK for watching movies etc. but I could reach those speeds with the 802.11g router as well!

I'm using the WDR4300 as access point, so I disabled DHCP server and NAT functionality, left the WAN port empty. And I set fixed IP in the subnet range of my modem/router. (horrible Speedtouch device). All works fine and stable, but too slow.

In the wireless settings I tried the 20 and 40MHz bandwith, disabled WMM, tried to lower the transmission power, tried to set a fixed channel. But all those changes do not have a significant influence on the transfer speed. (both on 2.4 and 5GHz) I'm the only 5GHz access point in my neighborhood, so interference cannot be a problem.
The clients indicate a link speed of 300mbps very close to the router, and this drops to indication of 54mbps further away, but effective link speed remains fairly constant (and stable!) (I find it strange that indicated link speed already drops at 3 meters with clear line of sight to the router)

I did the tests with fixed IPs on two laptops and no devices connected on the LAN ports, to rule out problems caused by the modem/router or other clients.The tests were done using a Lenovo x220 and Asus Zenbook, both with Intel dual band 802.11n wifi interfaces. The Lenovo reaches 22MByte/s via the Cisco access point at my work (with less signal as at home).

View 6 Replies View Related

TP-Link Dual-Band Wireless :: Use WDR4300 As Switch Rather Than Router?

Dec 6, 2012

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP : Verizon DSL

My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?

View 1 Replies View Related

TP-Link Dual-Band Wireless :: WRD3600 USB Storage Not Accessible?

Apr 26, 2013

Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

I'm having difficullty configuring a USB hard drive to my WDR3600

The WRD3600 is acting as a switch with my netgear cable modem router as the DHCP server. The DHCP server on the WRD3600 is turned off. the WRD3600 is accessible on my home network and I can connect to attached wifi and Ethernet devices.

when I attach my WD USB hard drive, I can see the device on the WDR3600 web GUI USB settings page. The WD hard drive service status is started and enabled. when I click on the open the disk link, nothing happens. When I try to access the 192.168.x.x/volume1 address, I get a page that says the username or password is incorrect.

When I disconnect the WDR3600 from the rest of my network and turn the DHCP server back on and connect directly to the router, i am able to access the connected usb hard drive.

is it possible to have the WDR3600 acting as a switch with DHCP server off and still access usb devices connected to it?

View 5 Replies View Related

TP-Link Dual-Band Wireless :: Upgrade Antenna On WDR3600?

Feb 27, 2013

Region : Brazil
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :

I want to change the antennas on my wdr3600 to increase the range of the signal because my walls are too thick. I can not find TP link brand Dual Band Antennas, so I search ebay and found this:

[url]....

Any dual band RP-SMA antenna is compatible with the WDR3600? or do I need to search for something in particular?

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 Crashes After About 24 Hours

Dec 26, 2012

Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

I got a new TP-Link TL-WDR4300, connected it to my online pure sine wave UPS like I did with my previous routers with no problem.After about 24 hours, router crashes - no access to web interface, no internet (wired or wireless), must reboot to get it to work again.Router was replaced, same problem with new router.The firmware is the latest one and is customized for Israel because of 5GHz limitations.I was told by the representative in Israel that I should try to connect it to another AC outlet instead of the UPS.

View 7 Replies View Related

TP-Link Dual-Band Wireless :: Wdr4300 - Can't Connect To Internet

Nov 7, 2012

Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Waoo, fiber

i just bought a WDR4300. tried the quick start, then tried to manually set it up like my old Router. but i cant connect to the internet. when i check the status. it often says that WAN is unplugged, no cable. But when i use same cabels and settings on my old router it works fin.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: Cable Modem And WDR4300 Don't Seem To Like Each Other

Feb 14, 2013

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : charter, its smarter.

so i have a sb6141 cable modem that is mine and not a lease. it works like a champ when hard wired to my desktop. i just got my hands on a new shiny tp-link wdr4300 yesterday and after messing with it for the better part of 2 hours, something seems to be amiss with the communication between the two. everything will be humming along fine and all of a sudden i get the dreaded PAGE CANNOT BE DISPLAYED. sure as the world i look at the modem and all the lights are off and its resetting itself. and honestly this continues until i pull the power and plug it back up. i think maybe one time in the middle of the night i actually saw it reset itself and then come back online.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: WR2543ND Keeps Dropping Connection

Feb 6, 2013

Region : UnitedKingdom
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : v1
ISP : plusnet

I have a WR2543ND router and everyday it drops the wireless connection . all the lights on the router stay on and im still connected to the router but it looses the internet connection . the windows trouble shooter says that it cannot connect to the dns server , I have to reset the router and my computer to get it working again . I Have updated the firmware but still the same

View 10 Replies View Related

TP-Link Dual-Band Wireless :: What IP For LAN When TL-WDR4300 Is Secondary Router

Feb 25, 2013

Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk

My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?

View 3 Replies View Related

TP-Link Dual-Band Wireless :: Slow Speed On WDR4300

Nov 6, 2012

Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Arrownet

I purchased a WDR4300 yesterday and have set it up. The internet is running smoothly although the transfer speed is rather slow. When transferring from my computer to my Seagate GoFlex Home i get about 6 - 8 mbps with Wireless N. The router is set to only use Wireless-N and my laptop has the latest drivers. I have also tried other computers in the house and the speed is the same. The GoFlex Home is connected to the router via a LAN cable. Prior to updating i used a Linksys WRT54GL and managed speeds of about 3 or 4 mbps over its G only connection. As for transfers between 2 computes the rate is about 1 - 3 mbps

As for distance the Wireless router is only about 1.5 meters from the laptop (across the room) with nothing in between them to cause interference. I have also checked what channels my neighbors use (using inSSIDer) and picked 13 as there is only 1 other person nearby on that channel and they are quite far away.

View 5 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - 2.4 Ghz Connected But Not Internet

Jan 6, 2013

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : time warner

This is frustrating I owned the router for about 2 weeks. my 2.4ghz is out. Basically I connect to the router on 2.4 can get into the tp-link admin webpage for the router but no internet at all. if I switch to 5 ghz everything works great, or if i use direct connect wire everything is great. I tried disabling NAT but that shut down all my internet connections across all links and manually switching to channel 1 did nothing at all i also tried channel 7. Ideas why only 2.4 ghz is affected out of the blue all of a sudden?

View 12 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4900 Will Have English Firmware

Apr 22, 2013

Region : Australia
Model : TL-WDR4900
Hardware Version : Not Clear

If wdr 7500 will have english firmware ? I bought the router in china and now back home in Australia its all in chinese?

View 6 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR 3600 Firmware Upgrade?

Apr 14, 2013

Region : Canada
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :

I'm wondering if I can install this version of the firmware: TL-WDR3600_V1_130320

It says: Notes: For TL-WDR3600(UN) V1 What is that (UN) version exactly ?

View 5 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - No Internet After New Firmware?

May 11, 2013

Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_130319
ISP : unfi

I unable connect to internet after upgrade the new firmware

View 1 Replies View Related

TP-Link Dual-Band Wireless :: WDR4300 Loses 2.4 Ghz Connection

Dec 10, 2012

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast

The 5 ghz connects fine for multiple machines however machines on 2.4 simultaneously lose their connection to the internet, sometimes saying it is still connected to the internet when it is not and sometimes losing connection with the router entirely. The 5ghz still works when this happens.

View 14 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - 300MHz Not Working

Mar 10, 2013

Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

I've been using inSSider on Windows and trying different settings on my 4300 to get wireless n @ 300MHz working with no luck. The maximum I seem to be able to get it to run is 144MHz.

Is this a fault with the router or the firmware? Since the router is advertised to run at 300Mhz, then by rights if it does not or cannot, then TP-Link owes everyone a refund, at least in Australia because this counts as false advertising.

I had a similar issue with my 1043ND as well. Has anyone got a 4300 working at 300 MHz?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved