Keep Getting The Error That No Compatible Hardware Was Found?
Nov 12, 2011
I am trying to install the WLAN driver for Dell Dimension 9200C desktop computer running Windows XP but I keep getting the error that no compatible hardware was found. I've gone to the appropriate Dell Drivers site for the computer's model and I'm 99% sure I downloaded the correct software for WLAN: Dell Wireless 1395 WLAN MiniCard. After going to Device Manager and looking under "Network Adapters", there is no Dell WLAN card at all (direct ethernet connection for internet works). Is it possible that the computer cannot find the WLAN network card, which prevents me from installing the driver software, even though it exists? If so, what can I do? If not, I guess I'll go buy a USB network adapter.
View 2 Replies
ADVERTISEMENT
Jul 3, 2012
Received my new 1510 mini wireless card card today for install in Inspiron 1525 running Vista 32bit.Laptop sees new device but cannot located driver. Run the disk that Dell sent, get message 'No compatible hardware found program will end'
Device manager shows yellow explanation mark under network tab..Have downloaded 6 or 7 different version of the driver but no joy.
View 1 Replies
View Related
Mar 4, 2013
Studio 1558, W7 x64 Ultimate SP1, 8gb ram, 500GB drive
I get a "No compatible hardware found" error when I try to load the drivers for the wireless card on my laptop.
I had to reload windows 7, ultimate x64 on my laptop. I've been able to install all of the drivers with the exception of the wireless card.
I've tried to load the R258276 driver for the broadcom chip as specified in my download with the Dell driver utility and dell system detect. This worked previously with the same os. I've also installed and ran Dell Support Center, PC check and System Detect.
My order lists the following wireless card:
WHDPC 1 Card, Wireless, Half Mini-Card, DW1501, 4313
I have an unknown device and a Network Controller flagged in "Other devices" in Windows Device Manager. I've deleted these and reran hardware detect and they both show of again as not having drivers installed. Windows update nor windows driver update locates valid drivers. I searched the forums and found a few links to other sources of he R258276 drivers, but got the same error msg.
View 1 Replies
View Related
Sep 3, 2012
when tryin to install new WLAN driver of the following details from dell website wit my service tag WLAN half mini card 1501 it displays no compatible hardware found
View 2 Replies
View Related
May 23, 2012
For the past week I've had a problem browsing the internet. Now, at first, this only happened starting at around 3 am central time and ending at about 6 am when I could browse the internet properly. As the days went forth, however, it began happening earlier at around 12 am. What would happen is this: would be on the internet browsing sites and whatnot. All of a sudden (As I'm loading a new page) I would get the "Address not found" error as if I'm not connected to the internet. I could try to reload any other page on my session,but sometimes it would halfway load (ei:not loading pictures, ect.) and other times I would get Address not found. This would go for about a 4 hour time period. After that, everything would be back to normal and I could go back on my session.
Now, I'm on my laptop via a router that is in my house. We also have a desktop computer, but I noticed this problem happening on my laptop first. When it first happened, it was only on my laptop. I had internet connection and could browse it endlessly on my desktop. As the days went on, however, my desktop started having the same problem connecting to the internet (I still noticed the problem on my laptop first and then I would go see if the desktop had it too).When this first happened, I was thinking my laptop wasn't connecting to my router. Instinctively, I reset the router to no avail. I also opened up IE (I don't use it much because it's just too slow) and tried to diagnose the problem using that. When I did this, it was giving me DNS as the problem of me not connecting to the internet. I am not a network admin so I don't know that much about DNS. I also used IE to diagnose the problem on the following days, but after the first time it only gave me a "You aren't connected to the internet" solution. Since then, I've been running a barrage of anti virus, rootkit, ect. just because I can and I haven't done it in a long time. I didn't find anything unusual in all the reports so I'm still not sure what the problem is.
View 3 Replies
View Related
Feb 11, 2013
i have 9 pcs on a lan. when i attempt to view the workgrp i get a message that indicates the the workgrp is not accessible and network path not found. i have tuned off windows and mcafee firewalls so that the only firewall functioning is with the modem/router(netopia) if i change the workgrp to the default(mshome) i can see the pcs.
View 2 Replies
View Related
Jun 20, 2011
i have a SMC8014WG-SI Router and its gateway is 192.168.0.1 but when i type it in the router doesn't appear at all , just says that the page cannot be found. i like portforwarding and need to be able to login the router to do so.
View 9 Replies
View Related
Sep 10, 2012
even after installing t driver,i'm getting t same error message.Wifi adapter cannot be found
View 1 Replies
View Related
Feb 18, 2012
We are monitoring everyday C-2500 router, the CRC and input error are increasing day by day.This are current readings as observed on 18 Feb.
C-2500-R1#sh int s0
Serial0 is up, line protocol is up
Hardware is HD64570
[Code].....
View 1 Replies
View Related
May 14, 2012
net send command not working. Even after starting messenger. Error : The Message Alias could not be found on the network
View 3 Replies
View Related
Sep 3, 2012
I am running a Windows 7 Professional 32 bit as my office computer. About 3 PCs in the office are connected to the office server through wireless connection (including mine), and another 3 are connected through a wired connection. My connection to the server doesn't work at times. I get an error message that "An error occurred while connecting to . The network path was not found." The other PCs using the network have no problem connecting to the server. Also, the internet connection is shared from the server and I have no trouble with it. The problem is only with accessing the shared folder on the server.
View 1 Replies
View Related
Nov 3, 2011
I have a server computer running Windows Server 2008 R2 Standard operating system with 4 client computers connected to the network running Windows 7 Professional operating system. All worked great yesterday. This morning, one of the client computers encountered this error:
An error occurred while reconnecting F: to \SERVERData
Microsoft Windows Network: The user name could not be found.This connection has not been restored.No updates or changes have occured between yesterday and today and the three other client computers have no similar problems.Just this one client has the error.
View 6 Replies
View Related
Jun 22, 2012
I have been having this issue for the past one week where though i am able to connect to the internet through the wired lan without any problem when i connect it to my buffalo wzr - hp - ag300h router it disconnects within 5 minutes and on trying to check the internet connection DHCP server not detected error is shown. I have another edimax router and i tried to setup wireless with that router and have the same problem of disconnection after 5 minutes. [code]
View 14 Replies
View Related
Feb 12, 2011
On my home LAN I have computers running Ubuntu 10.10, Win XP, Win7 32 bit and Win 7 64 bit, as well as an Iomega Home Network Media Drive. I can share files and folders between Ubuntu and XP without problem. I can CRUD (Create, Read, Update, Delete) to the Iomega device from all the computers. I can share folders when using the 64-bit Win 7 computer that are located on the XP computer.
I can see the 'users/Public' folder on the 64bit Win 7 computer from the XP computer (but that folder being empty, this access is not a lot of use - a secondary probelm). I cannot see my 'user name' files/folders on the Win 7 computer from the XP computer
From Computer, Network on the Win 7 computer I can see the Ubuntu computer by name (approximately - it's all in upper case, which is not correct as far as Ubuntu is concerned).
I cannot access files on the Ubuntu computer via its name - I receive the usual 'network path not found' error, inviting me to check the spelling of the computer, which I can see is wrong, but which I can find no way to correct.
If I try to access the Ubuntu computer by IP address, then I am presented with an 'Enter Network Password' panel. I have never allocated a network password, so I have no idea what user name or password to enter here. If I enter my valid account name forthe Win 7 machine, along with its valid password, then a Logon failure is reported: 'unknown user name or bad password'. If I use the single valid user name and password for the target Ubuntu computer, I receive the same failure message. I thought I had set the same user name on both computers (I certainly have the same password), but for reasons best known to Bill Gates, the username on the Win 7 computer has been initially capitalised, making it absolutely not the same as any valid user name on the Ubuntu computer.
So, in short, I can find no way to access the Ubuntu computer from Win 7. Further more the Ubuntu computer cannot see the Win 7 computer in the windows network at all.
I have the same internet security software (Comodo) running on all Windows computers. It is enabled on the XP computer. It is disabled on the Win 7 computer - but with no effect on the failure to connect.
View 1 Replies
View Related
Jun 26, 2011
Error message
305005: No translation group found for udp src c_dmz:10.0.176.120/51910 dst inside:195.244.192.16/53
305005: No translation group found for udp src c_dmz:10.0.176.120/51910 dst inside:195.244.192.166/53
[Code]....
I thought it needed a nat (c_dmz) command but I got the following error message
PIX(config)# nat (c_dmz) 0 0.0.0.0 0.0.0.0 0 0 nat 0 0.0.0.0 will be identity translated for outbound WARNING: Binding inside nat statement to outermost interface. WARNING: Keyword "outside" is probably missing.
View 2 Replies
View Related
Mar 2, 2012
on IOS versions higher than 12.2(50) on Cisco 3560G-48TS I get this error/traceback, when I reach a certain number of Access-lists group'ed to "interface vlan", and the ACL inserted in the TCAM reaches acl label #128 (can be seen with : Show platform acl label 128)I can see errors in the TCAM if I issue the command
View 21 Replies
View Related
May 31, 2011
I have a 5510 with just a inside and outside interface, everything works on the lan inc internet access and exchange hosting to the net, but I have another exchange server on the wan and I can't get to that because I'm not natting inbound traffic and the default route sends traffic elsewhere.
If I put a nat any statement on the inside interface inbound it works, however all LAN internet traffic fails with a No translation group found error.I've removed the static nat commands as they are all named anyway, but below is what I have before I do a nat any inside inbound command global (outside) 1 interfaceglobal (inside) 2 interfacenat (inside) 0 access-list inside_nat0_outboundnat (inside) 1 0.0.0.0 0.0.0.0.
View 3 Replies
View Related
Jun 20, 2011
Cannot turn off my windows firewalls on my vista toshiba after removing a scam Vista antivirus spyware download.. Cannot access any ports,Whenever I try to open a web browser, my disk defragmentation, ccleaner
View 1 Replies
View Related
Apr 3, 2011
I have Cisco ASA5510 OS version 8.4(1), when i try to apply static command, this command is not found, the NAT issues used nat(inside,outside).
So why i can't found this command ?
View 1 Replies
View Related
Dec 14, 2011
I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
logging enable
logging buffered 7
access-list ALL line 8 extended permit ip any any
[Code].....
View 4 Replies
View Related
Sep 4, 2011
I get the following error message at startup.
---
Error (2048) found in fsck check - attempt to repair.---
What is the implication of the error message 106007? Do I have no problem continuing to be left out of this error?
View 4 Replies
View Related
May 11, 2010
I've run in to this on 3750G's in a various sized stacks. We apply port security for a mac address on a single port (not existing on more than one port - that's a different issue that appears in multiple posts already).In this case:
1) We do a 'sho mac address-table and see that the device with the mac address in question lives on one port, port 1/0/x.
2) We apply mac port security for this exact same mac address to the same port it is already attached to. switch(config)#int g2/0/2 switch(config-if)#switchport port-security mac-address 001a.1ec8.abcd
3) Get this error: 'Found duplicate mac-address 001a.1ec8.abcd'.We again confirm that that is the only port on the entire switch that has this mac-address.Try the command again, same error.
4) We do a bunch of show commands, get in and out of the switch, go back and then try it again, and now it works, same command, same port and same mac address.
-Aging is default 300
-These are Cisco wireless AP's attached to the switch
-This occurs on different switches with different ports using different mac addresses, always same symptoms.
View 6 Replies
View Related
Jun 15, 2012
I thought I would leave a message on a problem. I did two chats to the support desk and this was not brought up and it is obvious. I just installed the 4200v2 as a replacement for a NetGear. I bought for the n performance and the USB for a shared disk/media file server. I connected a640G Western Digital My Book to the USB. I was able to see the drive in the asp interface of the router, but I kept getting the "error code: 0x80070035 network path not found" message. My computer is a 6 month old HP with Windows 7 running Bitdefender Internet. I found I could get to the drive from my wife's Toshiba (only used for browsing, so minimal security), so I thought it was a firewall issue (also what Cisco said). After doing some Internet mining, I found that the issue is the Netbios setting in IPv4. My PC had the setting Default, which requires the DHCP server to provide the setting and apparently this was not set by the 4200. Without Netbios the disk cannot be mapped. Changing this to NetBios "enabled" solved the problem. This can be reached by going into the Control panel:Network and Sharing Center. Click on the connection (either local area or wireless), then open the properties, click on the TCPv4, Click properties, then advanced. Go to the Win tab and select Netbios enabled.
View 1 Replies
View Related
Oct 6, 2012
I have two ACS v 5.2 (primary and secundary) and some users are in the internal stor and the others are in the AD.The local site topology is like this:
PC - AP - WLC - ACS - AD
Authentication method is PEAP(EAP-MSCHAPv2) and all user have the certificate company installed. The OS in the client users is Windows 7.Users was working fine but some users reports intranet disconnections. I see in the ACS log many "22056 Subject not found in the applicable identity store(s)." and "24415 User authentication against Active Directory failed since user's account is locked out" alarms.I believed it was because user wasn´t in the AD data base, but some times the same user is authenticated successfull and other i see the "22056...." or "24415...." alarms.
I switched the role for ACS primary to works as secundary and we see the same alarms.
View 2 Replies
View Related
Mar 12, 2013
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
View 5 Replies
View Related
May 1, 2012
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies
View Related
Apr 20, 2011
i'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies
View Related
Aug 9, 2011
compatible LAN driver for M2N-MX SE PLUS
View 4 Replies
View Related
Jan 22, 2013
I have a Cisco Router 881 with c880data-universalk9-mz.150-1.M7.bin IOS file. I want to upgrade to the latest IOS c880data-universalk9-mz.152-4.M2.bin. But when I upload the file, it appears the message The selected file c880data-universalk9-mz.152-4.M2.bin is not compatible with this router model.
View 4 Replies
View Related
Mar 18, 2011
I have a desktop PC running WinXP I recently got a laptop running Win7. I Set both of them up with the same workgroup name, and now my XP machine can see and access my laptop, but my lap can't see my XP machine. If it makes any difference, I can remote into my XP from my laptop, but that's not what I need.
View 3 Replies
View Related
Jan 11, 2011
I have wireless N router and just got wireless G usb adapter... but i dont get it to work.... can i manage to get it working or i need another adapter?
View 2 Replies
View Related
Aug 21, 2011
I have a customer with an ACS for Windows version 3.3. I know the ACS is End-of-support, but if I could do Authentication for a WLAN with a Controller 5508 Softwareversion 7.0.116.0 and how?
View 3 Replies
View Related
Aug 17, 2011
I am new to this forum. I ve been googling for CCNA explorer for last one month. All the versions that i download is not compatible with windows 7 and works fine with windows XP. Does anyone know if cisco has released any new version that is compatible with Windows 7?
View 6 Replies
View Related
