I get the following error message at startup.
---
Error (2048) found in fsck check - attempt to repair.---
What is the implication of the error message 106007? Do I have no problem continuing to be left out of this error?
Whether we can configure HA between AIR-CT5508-100-K9 and AIR-CT5508-25-K9. Or we should require this AIR-CT5508-HA-K9 ?
View 6 Replies View RelatedSince i upgraded to the latest firmware my WAG160N reboots, the same as others that i read here in the forum, now i need to revert to the old firmware but sadly when i check the File is not Found. Please, re upload the old firmware.
View 1 Replies View RelatedCisco... Have two new 3750X switches (24P-L, and 48PF) trying to stack. Brought them up together a few weeks ago with the 24P using LANBase and the 48 IPBase. The expected happened. They saw each other in the stack ring, and the 24 port was excluded due to license miss match. This was corrected. Now both are IPBase.Now I have the two switches stacked, and boot the 48 and 24 at the same time. Monitoring the 48 I get a check message "FIPS: Flash key check: End, Not found. FIPS: Stacking Not Found". The 48 does confirm the stack cable is connected. This happens early in the boot process, before master election.OK.... Now looking at the 24 Port. After applying the new license, and actually booting successfully and few times. It will no longer load the boot file. Wants an environment variable. Going to have to dig into ancient history for that. Had to deal with that one about 8 years ago. Do not feel that is part of the stack disable issue though.
View 2 Replies View RelatedI have been having this issue for the past one week where though i am able to connect to the internet through the wired lan without any problem when i connect it to my buffalo wzr - hp - ag300h router it disconnects within 5 minutes and on trying to check the internet connection DHCP server not detected error is shown. I have another edimax router and i tried to setup wireless with that router and have the same problem of disconnection after 5 minutes. [code]
View 14 Replies View RelatedThe router is always giving the below error:
Error : compressed image check sum is incorrect 0xDC5C5348
Expected a check sum of 0x066C5349
I have uploaded a new firmware but same issue after booting, I have check the MD5 check sum in the image and Cisco and they are matching and verified, what could be the reason for all of this ?
I thought I would leave a message on a problem. I did two chats to the support desk and this was not brought up and it is obvious. I just installed the 4200v2 as a replacement for a NetGear. I bought for the n performance and the USB for a shared disk/media file server. I connected a640G Western Digital My Book to the USB. I was able to see the drive in the asp interface of the router, but I kept getting the "error code: 0x80070035 network path not found" message. My computer is a 6 month old HP with Windows 7 running Bitdefender Internet. I found I could get to the drive from my wife's Toshiba (only used for browsing, so minimal security), so I thought it was a firewall issue (also what Cisco said). After doing some Internet mining, I found that the issue is the Netbios setting in IPv4. My PC had the setting Default, which requires the DHCP server to provide the setting and apparently this was not set by the 4200. Without Netbios the disk cannot be mapped. Changing this to NetBios "enabled" solved the problem. This can be reached by going into the Control panel:Network and Sharing Center. Click on the connection (either local area or wireless), then open the properties, click on the TCPv4, Click properties, then advanced. Go to the Win tab and select Netbios enabled.
View 1 Replies View RelatedFor the past week I've had a problem browsing the internet. Now, at first, this only happened starting at around 3 am central time and ending at about 6 am when I could browse the internet properly. As the days went forth, however, it began happening earlier at around 12 am. What would happen is this: would be on the internet browsing sites and whatnot. All of a sudden (As I'm loading a new page) I would get the "Address not found" error as if I'm not connected to the internet. I could try to reload any other page on my session,but sometimes it would halfway load (ei:not loading pictures, ect.) and other times I would get Address not found. This would go for about a 4 hour time period. After that, everything would be back to normal and I could go back on my session.
Now, I'm on my laptop via a router that is in my house. We also have a desktop computer, but I noticed this problem happening on my laptop first. When it first happened, it was only on my laptop. I had internet connection and could browse it endlessly on my desktop. As the days went on, however, my desktop started having the same problem connecting to the internet (I still noticed the problem on my laptop first and then I would go see if the desktop had it too).When this first happened, I was thinking my laptop wasn't connecting to my router. Instinctively, I reset the router to no avail. I also opened up IE (I don't use it much because it's just too slow) and tried to diagnose the problem using that. When I did this, it was giving me DNS as the problem of me not connecting to the internet. I am not a network admin so I don't know that much about DNS. I also used IE to diagnose the problem on the following days, but after the first time it only gave me a "You aren't connected to the internet" solution. Since then, I've been running a barrage of anti virus, rootkit, ect. just because I can and I haven't done it in a long time. I didn't find anything unusual in all the reports so I'm still not sure what the problem is.
We are monitoring everyday C-2500 router, the CRC and input error are increasing day by day.This are current readings as observed on 18 Feb.
C-2500-R1#sh int s0
Serial0 is up, line protocol is up
Hardware is HD64570
[Code].....
I am trying to install the WLAN driver for Dell Dimension 9200C desktop computer running Windows XP but I keep getting the error that no compatible hardware was found. I've gone to the appropriate Dell Drivers site for the computer's model and I'm 99% sure I downloaded the correct software for WLAN: Dell Wireless 1395 WLAN MiniCard. After going to Device Manager and looking under "Network Adapters", there is no Dell WLAN card at all (direct ethernet connection for internet works). Is it possible that the computer cannot find the WLAN network card, which prevents me from installing the driver software, even though it exists? If so, what can I do? If not, I guess I'll go buy a USB network adapter.
View 2 Replies View Relatedi have 9 pcs on a lan. when i attempt to view the workgrp i get a message that indicates the the workgrp is not accessible and network path not found. i have tuned off windows and mcafee firewalls so that the only firewall functioning is with the modem/router(netopia) if i change the workgrp to the default(mshome) i can see the pcs.
View 2 Replies View Relatedi have a SMC8014WG-SI Router and its gateway is 192.168.0.1 but when i type it in the router doesn't appear at all , just says that the page cannot be found. i like portforwarding and need to be able to login the router to do so.
View 9 Replies View Relatedeven after installing t driver,i'm getting t same error message.Wifi adapter cannot be found
View 1 Replies View RelatedI'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
Error message
305005: No translation group found for udp src c_dmz:10.0.176.120/51910 dst inside:195.244.192.16/53
305005: No translation group found for udp src c_dmz:10.0.176.120/51910 dst inside:195.244.192.166/53
[Code]....
I thought it needed a nat (c_dmz) command but I got the following error message
PIX(config)# nat (c_dmz) 0 0.0.0.0 0.0.0.0 0 0 nat 0 0.0.0.0 will be identity translated for outbound WARNING: Binding inside nat statement to outermost interface. WARNING: Keyword "outside" is probably missing.
on IOS versions higher than 12.2(50) on Cisco 3560G-48TS I get this error/traceback, when I reach a certain number of Access-lists group'ed to "interface vlan", and the ACL inserted in the TCAM reaches acl label #128 (can be seen with : Show platform acl label 128)I can see errors in the TCAM if I issue the command
View 21 Replies View RelatedI have a 5510 with just a inside and outside interface, everything works on the lan inc internet access and exchange hosting to the net, but I have another exchange server on the wan and I can't get to that because I'm not natting inbound traffic and the default route sends traffic elsewhere.
If I put a nat any statement on the inside interface inbound it works, however all LAN internet traffic fails with a No translation group found error.I've removed the static nat commands as they are all named anyway, but below is what I have before I do a nat any inside inbound command global (outside) 1 interfaceglobal (inside) 2 interfacenat (inside) 0 access-list inside_nat0_outboundnat (inside) 1 0.0.0.0 0.0.0.0.
net send command not working. Even after starting messenger. Error : The Message Alias could not be found on the network
View 3 Replies View RelatedI am running a Windows 7 Professional 32 bit as my office computer. About 3 PCs in the office are connected to the office server through wireless connection (including mine), and another 3 are connected through a wired connection. My connection to the server doesn't work at times. I get an error message that "An error occurred while connecting to . The network path was not found." The other PCs using the network have no problem connecting to the server. Also, the internet connection is shared from the server and I have no trouble with it. The problem is only with accessing the shared folder on the server.
View 1 Replies View RelatedI have a server computer running Windows Server 2008 R2 Standard operating system with 4 client computers connected to the network running Windows 7 Professional operating system. All worked great yesterday. This morning, one of the client computers encountered this error:
An error occurred while reconnecting F: to \SERVERData
Microsoft Windows Network: The user name could not be found.This connection has not been restored.No updates or changes have occured between yesterday and today and the three other client computers have no similar problems.Just this one client has the error.
I have Cisco ASA5510 OS version 8.4(1), when i try to apply static command, this command is not found, the NAT issues used nat(inside,outside).
So why i can't found this command ?
I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
logging enable
logging buffered 7
access-list ALL line 8 extended permit ip any any
[Code].....
On my home LAN I have computers running Ubuntu 10.10, Win XP, Win7 32 bit and Win 7 64 bit, as well as an Iomega Home Network Media Drive. I can share files and folders between Ubuntu and XP without problem. I can CRUD (Create, Read, Update, Delete) to the Iomega device from all the computers. I can share folders when using the 64-bit Win 7 computer that are located on the XP computer.
I can see the 'users/Public' folder on the 64bit Win 7 computer from the XP computer (but that folder being empty, this access is not a lot of use - a secondary probelm). I cannot see my 'user name' files/folders on the Win 7 computer from the XP computer
From Computer, Network on the Win 7 computer I can see the Ubuntu computer by name (approximately - it's all in upper case, which is not correct as far as Ubuntu is concerned).
I cannot access files on the Ubuntu computer via its name - I receive the usual 'network path not found' error, inviting me to check the spelling of the computer, which I can see is wrong, but which I can find no way to correct.
If I try to access the Ubuntu computer by IP address, then I am presented with an 'Enter Network Password' panel. I have never allocated a network password, so I have no idea what user name or password to enter here. If I enter my valid account name forthe Win 7 machine, along with its valid password, then a Logon failure is reported: 'unknown user name or bad password'. If I use the single valid user name and password for the target Ubuntu computer, I receive the same failure message. I thought I had set the same user name on both computers (I certainly have the same password), but for reasons best known to Bill Gates, the username on the Win 7 computer has been initially capitalised, making it absolutely not the same as any valid user name on the Ubuntu computer.
So, in short, I can find no way to access the Ubuntu computer from Win 7. Further more the Ubuntu computer cannot see the Win 7 computer in the windows network at all.
I have the same internet security software (Comodo) running on all Windows computers. It is enabled on the XP computer. It is disabled on the Win 7 computer - but with no effect on the failure to connect.
I've run in to this on 3750G's in a various sized stacks. We apply port security for a mac address on a single port (not existing on more than one port - that's a different issue that appears in multiple posts already).In this case:
1) We do a 'sho mac address-table and see that the device with the mac address in question lives on one port, port 1/0/x.
2) We apply mac port security for this exact same mac address to the same port it is already attached to. switch(config)#int g2/0/2 switch(config-if)#switchport port-security mac-address 001a.1ec8.abcd
3) Get this error: 'Found duplicate mac-address 001a.1ec8.abcd'.We again confirm that that is the only port on the entire switch that has this mac-address.Try the command again, same error.
4) We do a bunch of show commands, get in and out of the switch, go back and then try it again, and now it works, same command, same port and same mac address.
-Aging is default 300
-These are Cisco wireless AP's attached to the switch
-This occurs on different switches with different ports using different mac addresses, always same symptoms.
Cannot turn off my windows firewalls on my vista toshiba after removing a scam Vista antivirus spyware download.. Cannot access any ports,Whenever I try to open a web browser, my disk defragmentation, ccleaner
View 1 Replies View RelatedIs it possible to have a license loaded on an AIR-CT5508-HA-K9 in order to have it working as a stand alone controller?
View 4 Replies View Relatedwe do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version 6.0.188.0.AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
The APs and controllers are connected to the LAN campus.Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-z.122-33.SXI1.bin on it.APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
I performed some troubleshooting steps.
- As we have some other controllers available over WAN, I tested the 1242 AP with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version 6.0.188.0 over WAN and this worked always okay.
- I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
- I also brought the second controller down to eliminate potential issue with having two of them up.
- The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
- I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
- As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options under Security/AP Policy,but this did not work.
- I also tried to reboot the controller, no improvement.
- The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.I can reproduce this, can also send debugging logs if needed.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- [URL]
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
AIR-LAP1242G-E-K9 10.0.13.28 log
*Mar 1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
*Mar 1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
[code]....
I've two wlc model CT5508 version 7.0.116.0. They are working fine except for the RF grouping part. When I look at the RF Group members part in the configuration, I can see only one wlc (the one I'm connected to). If I connect to the second one, in the same part, I've just one controller (so the second one..). I tried to restart the algorithm but no change. Each controller is configured with Group Mode set to auto, and their respective role are auto-leader...I tried to change the RF group name on both wlcs, but it didn't fix the problem. When I look at the logs, there is one which appear quite often:
*emWeb: Nov 29 10:32:07.764: %LOG-6-Q_IND: dtl_arp.c:2581 ARP input q exceeds limit. Current val = 50 [...It occurred 38 times.!]
I have issue about Wireless controler , i have 2x WS-C3750G-24WS and 1x AIR-CT5508-50-K9 , i have max 50 access point license and i can't upgrading because WS-C3750G-24WS is and of life , can i use AIR-CT5508-50-K9 with 3750G to work together? , mobility and everything....
View 1 Replies View Relatedi received access point types AIR-LAP1252AG-E-K9, which i want to connect to my wlan controller AIR-CT5508-K9. Update from IOS etc. is working fine. Also all access points are recognized by the controller.We got the AIR-LAP1252AG-E-K9 with two antenna versions.
View 1 Replies View RelatedI’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
What is the operating and/or peak power consumption (in kW) of a 5508 WLC with redundant power supplies?
The below power details are from the 5508 datasheet which lists 115 W as the maximum draw (0.115 kW) however this seems a bit low, is this right?
Input power: 100 to 240 VAC; 50/60 Hz; 1.05 A at 110 VAC, 115 W Maximum; 0.523 A at 220 VAC, 115 W Maximum; Test Conditions: Redundant Power Supplies, 40C, Full Traffic. Heat Dissipation: 392 BTU/hour at 110/220 VAC Maximum Cisco 5500 Series Wireless Controllers Data Sheet: [URL]
Basically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.