The router is always giving the below error:
Error : compressed image check sum is incorrect 0xDC5C5348
Expected a check sum of 0x066C5349
I have uploaded a new firmware but same issue after booting, I have check the MD5 check sum in the image and Cisco and they are matching and verified, what could be the reason for all of this ?
i have a router 1841 series and LMS send me amessage telling me the VPN AIM is not working on thsi device and i want to check the status of this VPN card
View 1 Replies View RelatedThe router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I get the following error message at startup.
---
Error (2048) found in fsck check - attempt to repair.---
What is the implication of the error message 106007? Do I have no problem continuing to be left out of this error?
I'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
Error : compressed image checksum is incorrect 0xDC5C5348 Expected a checksum of 0x066C5349I have uploaded a new firmware but same issue after booting, I have check the MD5 checksum in the image and Cisco and they are matching and verified, what could be the reason for all of this ??
View 2 Replies View RelatedI have an 1841 that was working fine - I could SSH to it with my Radius login and console into it with local credentials ("Fred").I added another use ("Mike") with priv 15 so the end user could log in locally via console if needed.After that, we can both log in via console, but when we try to enter privileged mode we get "% Error in Authentication", before even entering the password.I can still log in via Radius SSH with no problems and access privilege mode via SSH.What am I missing so we can have two different users be able to log in locally with different credentials and access privileged mode, and keep my ssh radius working?
View 3 Replies View RelatedI have a Cisco 1841 router connected to two different lines (same ISP) and I would like to load balance between them. I think I have achieved this point, but the problem is that remote VPNs do not work (only from Dialer1).This is my diagram:
ISP1----ISP Router----------Fa0/1 ROUTER 1841
----------Fa0/0 LAN
ISP2 ----------------pppoe Dialer1 ROUTER 1841
I have tried to redirect all my vpn traffic through the Dialer1 with PBR, but it does not work.
We are using Cisco Router 1841 and users reporting issue related to VoIP. After investigation, seeing input errors on Router LAN interface, but there is no error on connected switch interface. [code]
View 2 Replies View RelatedI have a question for all those here who have experience with both Cisco ASAs and CheckPoint.Which do you prefer Cisco ASA or CheckPoint?
View 9 Replies View RelatedSimply one step away to check your IP address: type into your search box in your browser the following address
[url]....
I have a Cisco ASA5520 that we are going to use to allow users to connect to our network via the Anyconnect client, I have authentication set up to validate against AD via LDAP, but was wondering if there were any way to set up the profile to check the PC before they log in....we do not want users using their home PCs to attach to our corporate network, only PCs that were issued to them by the company. Nothing is jumping out at me in the config, we are running some fairly old sofware on the boxes (ASA - v8.2(2), Anyconnect - v2.5.3046) I plan on upgrading the Anyconnect to v3.1 but will probably need to keep running the 8.2(2) version on the ASA due to support issues.
View 2 Replies View Relatedi know in Cisco PIX til 8.2 OS, if i have Nat control disabled and ACL permitting connection from Low Secirity ( DMZ ) to High Secuurity (INSIDE) then connectino should be successful, and i dont need any STATIC identity nat of inside IP to be created.
But i have Cisco PIX 525 with Version 7.2(2) Which is not allowing connection from DMZ to INSIDE , although nat control is disabled. and giving RFP check failure, any thought?
PIT525PIXINET# sh running-config nat-control no nat-cont
packet-tracer input dmZ tcp 192.168.85.4 65000 10.34.21.25 3389
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
[Code]...
Some1 browse my PC via LogMeIn Hamachi, so i need 2 know who did that , how 2 see the log list?
View 1 Replies View RelatedHow do I check IP address of others, when in chatting or playing online game, I could only know that he is Mr. X from YZA country which appears on Screen, But I also know he is using with wrong name and wrong Country name.I would to check his IP as well as his Place?
View 1 Replies View RelatedI want to check the transfer speed between my PC and another IP.The IP belongs to a DVR here is the general schematic of the sistem:Digital Video Recorder - Dynacolor - DynaGuard H.264 DVR (nDG80 - nDG600 - DG200) & DynaHawk Speed Dome & IP CamerFirst when I've worked with this system everything worked well but now after three weeks I have to open 5 ore more internet explorer windows to see live image and I can't see the recordings.I need to know the speed transfer because I want to know if someone had decreased my transfer speed between my PC and the router or DVR.
View 3 Replies View RelatedHow to check which users are using printer. so that i can see which user are using more printer.
View 2 Replies View RelatedHow to check dhcp if not working
View 1 Replies View RelatedHow do i check my LAN connection speed- is the same as the speedtest t I run from the internet ?
View 1 Replies View RelatedAt one time a windstream (my internet provider) had talked me through a way to check the speed of my connections for my wireless network....I can' find the bookmark this was. How I can check this?
View 4 Replies View Relatedhow do i check the listed ip's on my server?
View 1 Replies View RelatedHow To Check If Someone Is Stealing Wi-Fi
View 9 Replies View RelatedHow To Check If Someone Is Stealing Wi-Fi
View 1 Replies View RelatedHow is the best and easiest way to check kind of load balancing on the routers using BGP (Border Gateway Protocol)?
View 6 Replies View Relatedknow software that can show us software that shows most used websites through particular firewall?
View 8 Replies View RelatedHow can we check when we connect using VPN client software if traffic is getting encrypted ?
View 7 Replies View RelatedYesterday, myself and local support team has been engaged to perform troubleshooting the issue of some web site accessing .Mos of this case is cased by MTU issue, So, I've tried to configure the following configuration on interface tunnel 0.Device: Cisco 7609 with IOS s72033-adventerprisek9_wan-mz.122-18.SXF8.bin
I've tried to figure out what the supporting command after 'ip tcp' in tunnel 0 and following likes..ip tcp ?compression-connections Maximum number of compressed connectionsheader-compression Enable TCP header compression.there is no such command about 'ip tcp adjust-mss.So, my questions is that what is the replace command for 'ip tcp adjust-mss' ? Is this only support on Router? such as Cisco 7200. or not, to take effect same functional on C7609, what is the command for that?
ASA running 8.2(5).When I enable ip spoofing on my network interfaces I see this getting logged:
Deny UDP reverse path check from 10.100.100.102 to 10.100.100.255 on interface SPECTRA-LAN
This is because interface SPECTRA-LAN (VLAN50) is the interface connected to the network with ip 10.100.100.0/24 but the interface do not have a ip address so it does not exist in the routing table I believe?However interface INTERN do also belong to network 10.100.100.0/24 which also is the management interface and the default route for hosts in network 10.100.100.0/24, but has no vlan.
1. move the management0/0 to SPECTRA-LAN and give SPECTRA-LAN ip 10.100.100.1?
2. give SPECTRA-LAN a ip address in the 10.100.100.0 range?
My routing table and interface list is:
Current available interface(s):
DATA-BACKUP Name of interface Redundant1.10
DMZ Name of interface Redundant1.900
GUEST Name of interface Redundant1.990
HOSTING Name of interface Redundant1.100
Infrastruktur Name of interface Redundant1.20
[code]....
I am working with ACS 5.2 and using Radius authentication for vpn client.
The authentication method used is Active Directory in an Windows enviroment with multiple domains in the same forest.
My problem occurs when i change a user from one group to another in Active Directory. After that i receive the following message when try to connect:
15039 Selected Authorization Profile is DenyAccess
The message is because match the default policy. Another user in the same AD group works fine. All domain in the forest have trust relation each other. I am using universal groups to include users from all domain belongs this forest.
how can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies View RelatedDoes ASA 8.4.3 check the source IP address of a DNS reply and drop it if the reply address is different to that in the query?
Customers DNS server does this due to a recent change, their server now has a virtual address, but replies are sent from its physcial address. This is temporary. Their PIX is happy with this.
Replace the PIX with the ASA, DNS fails, the only reason I can see is due to the way their internal DNS operates.
How can you check if balance ACA is enabled in CSS11503? How can you see also if the content switch(CSS11503) is load balancing using balance ACA? "show load" command does not show it.
xxxxxx# show load Global load information:
Reporting:Enabled
Calculation method:Relative Step Size:Dynamic Configured:10 Actual:1280
Threshold:254 Ageout-Timer:60 Teardown-timer: Configured:20 Actual:20
Service load information: Average Average Peak Average Service Name Load Number ResponseTime Response Time ----------------------------------------------------------------------- DNS1 4 8999 33972 DNS2 4 8884 28254 SSH-WPHGT11 2 0 87509 WPHGT11 2 0 0 def-gwy-server 255 0 0 fe1-gw1-radius1 2 0 0 fe1-gw1-radius2 2 0 0 fe1-gw1-wap-8799 8 15344 662337 fe1-gw1-wap-9200 2 [Code].....
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies View Related