Cisco ASA Or Check Point
Feb 28, 2011I have a question for all those here who have experience with both Cisco ASAs and CheckPoint.Which do you prefer Cisco ASA or CheckPoint?
View 9 Replies
ADVERTISEMENT
Check For The Mac Address Of Existing Access Point?
Sep 30, 2011how to check the mac address of a existing access point that i want to connect to the wired network.
View 1 Replies View RelatedCisco Firewall :: ASA 8.4 Newer Check Point Conversion Tool?
Feb 8, 2012Is there a newer tool for current versions of Checkpoint to ASA 8.4? I notice a lot of similarity between checkpoint and 8.4 now, but I still have to do it all line by line which has become a PITA.
View 1 Replies View RelatedCisco Application :: Double-check Point With Forum On Licensing On 4710 Appliance
Jan 9, 2013I would just like to double-check a point with the forum on licensing on 4710 Appliance.If with version 4.2 and above 2Gbps Bandwidth licence is required, the output of the sho license status should be?
View 1 Replies View RelatedCisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedCisco Switching/Routing :: 1941 / K9 VPN Router MPLS IPVPN Point-to-point
Mar 15, 2012I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?
2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.
Cisco Routers :: RVS4000 / ISP WISP Point To Point Network Project?
Nov 30, 2012Currently in place ISP WISP Point to Point network would like some pointers to exceed in doing it right. Here are some issues.ISP Fiber 50 Megs down and 50 Megs up ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?
a. Due to Port forwarding
b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1
1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1
a. Can I setup 74.144.55.159:85 to see 10.1.19.33?
My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx) Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought. 90% of users are out in the country without high speed internet.
Cisco Wireless :: 1310 Point-to-point Bridge In Lightweight Mode?
Apr 24, 2011how is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Cisco Switches :: SG500x Point To Point Connection Very Slow After 1.30.59 Update
May 1, 2013I have a point to point 100mb line connecting SG500x switches at 2 locations, with these ports in a vlan together. I use layer 3 on the SG500x's to route between the two sites. I also have RIP protocol enabled to allow for automatic failover if the point to point fails (this works well).
I upgraded the ios to 1.30.59, and the connection now runs at a fraction of the speed. I have hard-coded the ports to run at 100mb full duplex, but I still only get around 12mb of throughput between the switches. I used to get about 90mb before. The provider also hard-coded the circuit to 100mb full duplex. The provider has checked the circuit remotely, and everything looks fine. I tested with a laptop at each side, and did get almost 70mb throughput. I would think this indicates some type of setting mismatch, but i cannot find anything.
I am using a backup vpn for now as some things look flaky as well (on vpn, I can use the web interface to access the SG500x on the opposite side, but on the point to point I cannot - I can ping the device though).
I have seen some references on here to shutting off STP on these 2 ports.
Cisco WAN :: VWIC3-1MFT-T1 / E1 / Point To Point Serial Link Configuration?
Jan 12, 2011How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
View 1 Replies View RelatedCisco Wireless :: Configure 1310 Point-to-point Bridge (AIR-BRI1310G-A-K9-R)
Apr 24, 2011Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View RelatedCisco Firewall :: Terminate Point To Point Link Between 3750 And 6506?
May 20, 2012I all we are going to terminate point to point link between 3750 and 6506.
on 6506
int gi1/45
no switchport access
ip address 192.X.0.x 255.255.255.0
no shut
[code]....
Does this config correct as i am configuring between stack switch and 6506
Cisco WAN :: HWIC 4ESW Need To Configure Point To Point Data Dual Leased Lines
Jan 18, 2012We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View RelatedCisco Switching/Routing :: 2960 To Assign 2MB To Point To Point Connection For Voice Vlan
Sep 11, 2012recently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.
View 3 Replies View RelatedCisco WAN :: Catalyst 6509 Switches Connected Directly Using Direct Point To Point Link
Apr 14, 2013I have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.
View 5 Replies View RelatedCisco WAN :: Point To Point Connection In L2TPv3 With A Bandwidth Pass Through Of 1 Gb
Sep 4, 2012I would to realize an point to point connection in L2TPv3 with a bandwidth pass through of 1 Gb. Which routers/switches I can use?
View 3 Replies View RelatedCisco Wireless :: AP1242G Point-to-Point Bridge Configuration?
Mar 16, 2013I have two Cisco AP 1242G and i'm trying to configurate a Point-to-Point Bridge Configuration to connect two wired LAN. Figure 1.8 [URL] I would connect two wired networks.
I tryed two configurations: Root and Non-Root AP. This way every wired PC on the Root AP can connect to the Access points, but cannot connect to the wired PC on the Non-Root AP.AP and WGB. Even this way the wired computers on one AP cannot connect to the wired PC on the WGB. This way only the wireless client can connect to the wired network. This is my network:
Root Bridge Non Root Bridge
10.0.0.1 10.0.0.2
Wired clients on the RB Wired clients on the Non RB
10.0.0.100 10.0.0.200
Cisco WAN :: MWR2941 Qos Solution For 10mb Point-to-point L2 WAN Link
Jul 18, 2011We have a MWR2941 (running 12.4(20)MR) router on site A and one in site B which will be connected over a Service provider L2VPN Ethernet over MPLS (EoMPLS) Network, with 10Mb Bandwidth allocated by the ISP. I have simulated this in the lab by directly connecting the two MWR's back-to-back via the Gig0/0 interface with configurable bandwidth of 10Mb on the Trunk interface.
The E1 TDM pseudowire end to end is working fine, with PTP configured for E1 timing/clocking. In addition I have a 2960-24PC-L switch connected on G0/2 of the MWR (on each end) configured with dot1q trunking. The switch will be used to connect two user groups in two seperate vlans (VlanA and vlanb) and transported across the same 10MB wan Link. Below are the requirements
1) Classify and mark Psuedowire packets E1-DATA coming from a E1/CEM interface and give it priority treatment over the WAN Link with reserved bandwidth of at least 4MB
2) Classify and mark Signalling/Timing PTP packets coming from PTP Vlan and give it strict bandwidth reservation over the WAN Link of 1MB
3) Classify and mark vlan A traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
4) Classify and mark vlan B traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
It is important that the E1 Traffic and the Signalling/Timing PTP packets are given priority and strict reservation so that it is not dropped in times of congestion. At the same time Vlan A and Vlan B need bandwidth reservation to give them their guaranteed bandwidth.
Currently I have tried applying policy map to the CEM interface. However, I am having trouble matching anything on the CEM input. Also I am having trouble applying a service-policy outbound on the gig0/0 (WAN Link). Also I can’t apply a service-policy inbound on the Gig0/2 interface with match statement. I have tried configuring input policy map to classify and mark PTP traffic (Vlan 902), but the MWR does not also allow me to attach a service-policy to the vlan interface. how to configure the MWR and have a workable QOS solution.
Cisco Wireless :: Aironet 1310G - Point To Point Bridge
Oct 14, 2012Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".
View 16 Replies View RelatedCheck Your IP Address In Just About 3 Second?
Feb 28, 2012Simply one step away to check your IP address: type into your search box in your browser the following address
[url]....
Cisco WAN :: 3845 / How To Configure Vrf For Point To Point Link
Mar 11, 2013i have cisco 3845 router,how to configure vrf for point to point link .
View 1 Replies View RelatedCisco WAN :: 1760 Point To Point Fiber Connection
Feb 28, 2012We have two locations 10 miles apart and need connectivity between them. A local provider can run a 30MB fiber connection between the 2 sites at a very reasonable cost. We would have to provide the routers however. I have worked with Cisco routers before with T1 channelized connections but am unsure how the the fiber would connect to a Cisco router in this scenerio. I need to know how such a connection to the routers at each end would take place, specifically what WIC or whatever else would be needed. I currently have a 1760 router at each site but realize that they are old and I m,ay have to replace them with newer models.
View 11 Replies View RelatedCisco VPN :: 877 - Configuration For Point To Point IPSec Tunnel
Oct 25, 2011I have problems with a vpn configuration for point to point ipsec tunnel.Communication stops randomly, I have the ability to view any record or log of court?
model cisco router on a 877
Cisco VPN :: 2921 - NAT Ports Filtered Over Point-To-Point VPN
Feb 22, 2011I have a Cisco 2921 configured with both DMVPN for remote sites and point-to-point isakmp ipsec VPN for smaller residential end-points.
The issue is, any ports that are NAT'd from the external appear filtered on the point-to-point vpn endpoints, but work fine over the dmvpn. Everything else seems to work correctly over the vpn. I have the nonat acl set up and the port forwards work fine from the external, but I'm not sure what's happening.
I have the configuration on the 2921 for reference.
Cisco WAN :: Allowing Dota In Point-point (wan) Using 2811
Jun 22, 2012find out the necessary configuration on our cisco router 2811 on how to pass through the Dota game application?
View 1 Replies View RelatedCisco VPN :: ASA5520 Any Way To Set Up Profile To Check PC
Mar 5, 2013I have a Cisco ASA5520 that we are going to use to allow users to connect to our network via the Anyconnect client, I have authentication set up to validate against AD via LDAP, but was wondering if there were any way to set up the profile to check the PC before they log in....we do not want users using their home PCs to attach to our corporate network, only PCs that were issued to them by the company. Nothing is jumping out at me in the config, we are running some fairly old sofware on the boxes (ASA - v8.2(2), Anyconnect - v2.5.3046) I plan on upgrading the Anyconnect to v3.1 but will probably need to keep running the 8.2(2) version on the ASA due to support issues.
View 2 Replies View RelatedCisco Firewall :: NAT RPF Check Failure PIX 8.2 OS
May 2, 2013i know in Cisco PIX til 8.2 OS, if i have Nat control disabled and ACL permitting connection from Low Secirity ( DMZ ) to High Secuurity (INSIDE) then connectino should be successful, and i dont need any STATIC identity nat of inside IP to be created.
But i have Cisco PIX 525 with Version 7.2(2) Which is not allowing connection from DMZ to INSIDE , although nat control is disabled. and giving RFP check failure, any thought?
PIT525PIXINET# sh running-config nat-control no nat-cont
packet-tracer input dmZ tcp 192.168.85.4 65000 10.34.21.25 3389
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
[Code]...
Cisco WAN :: To Check Status Of VPN 1841
Dec 15, 2010i have a router 1841 series and LMS send me amessage telling me the VPN AIM is not working on thsi device and i want to check the status of this VPN card
View 1 Replies View RelatedCisco WAN :: Check Sum Error In 1841
Oct 7, 2012The router is always giving the below error:
Error : compressed image check sum is incorrect 0xDC5C5348
Expected a check sum of 0x066C5349
I have uploaded a new firmware but same issue after booting, I have check the MD5 check sum in the image and Cisco and they are matching and verified, what could be the reason for all of this ?
Check The Users That Logged Into PC?
Mar 27, 2011Some1 browse my PC via LogMeIn Hamachi, so i need 2 know who did that , how 2 see the log list?
View 1 Replies View RelatedCheck Others IP Address And Location?
Sep 4, 2011How do I check IP address of others, when in chatting or playing online game, I could only know that he is Mr. X from YZA country which appears on Screen, But I also know he is using with wrong name and wrong Country name.I would to check his IP as well as his Place?
View 1 Replies View RelatedHow To Check Transfer Speed
Jun 12, 2011I want to check the transfer speed between my PC and another IP.The IP belongs to a DVR here is the general schematic of the sistem:Digital Video Recorder - Dynacolor - DynaGuard H.264 DVR (nDG80 - nDG600 - DG200) & DynaHawk Speed Dome & IP CamerFirst when I've worked with this system everything worked well but now after three weeks I have to open 5 ore more internet explorer windows to see live image and I can't see the recordings.I need to know the speed transfer because I want to know if someone had decreased my transfer speed between my PC and the router or DVR.
View 3 Replies View Related