Cisco Switching/Routing :: Input Error And CRC Error On Router 1841?
Mar 12, 2013
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
View 5 Replies
ADVERTISEMENT
Feb 18, 2013
We are using Cisco Router 1841 and users reporting issue related to VoIP. After investigation, seeing input errors on Router LAN interface, but there is no error on connected switch interface. [code]
View 2 Replies
View Related
Aug 14, 2011
I have upgraded the firmware on my Linksys BEFSR41 V4.3 router. On this router i used Statis IP (so DHCP enabled). This worked fine on my network, until this upgrade. Now when i try to ad another static IP , or when i want to change something in the Routing-tab, i get this message ' Wrong Gateway Input! It should be the same subnet with WAN IP'. Strange because i haven't changed anything in the settings.I already did a complete reset on the router, still the same problem.
View 7 Replies
View Related
Apr 15, 2012
Whenever I use the following command I get an invalid input error
ciscoasa#conf t
ciscoasa (config) # crypto isakmp enable outside
ciscoasa (config) #object network net-local
ciscoasa (config-network) # subnet 192.168.101.0 255.255.255.0
^
I have reset the firewall (cisco 5505) to factory default. The marker ^ is under the subnet
View 10 Replies
View Related
Jan 22, 2013
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[code].....
View 1 Replies
View Related
Nov 8, 2011
I was trying to give the following host name to my 3925 router.Iht comes up with the following error. DRT0(config)#hostname DRT#0 % Hostname contains one or more illegal characters.% Hostname "DRT#0" is not a legal LAT node name, Using "CISCO_000000" DRT#0(config)#
View 2 Replies
View Related
Jul 30, 2012
Error : compressed image checksum is incorrect 0xDC5C5348 Expected a checksum of 0x066C5349I have uploaded a new firmware but same issue after booting, I have check the MD5 checksum in the image and Cisco and they are matching and verified, what could be the reason for all of this ??
View 2 Replies
View Related
Oct 7, 2012
The router is always giving the below error:
Error : compressed image check sum is incorrect 0xDC5C5348
Expected a check sum of 0x066C5349
I have uploaded a new firmware but same issue after booting, I have check the MD5 check sum in the image and Cisco and they are matching and verified, what could be the reason for all of this ?
View 6 Replies
View Related
May 28, 2013
We are having Cisco ASA 5540 having Cisco Adaptive Security Appliance Software Version 8.0(5)23 at certain time of moment daily wer are facing latency and packetdrop wherin when I checked for ASA Interface which gives me " Input Errors" on outside interface ,so can any one tell me what are the causes to get input errors on cisco asa outisde interface.
View 2 Replies
View Related
May 15, 2013
I have an 1841 that was working fine - I could SSH to it with my Radius login and console into it with local credentials ("Fred").I added another use ("Mike") with priv 15 so the end user could log in locally via console if needed.After that, we can both log in via console, but when we try to enter privileged mode we get "% Error in Authentication", before even entering the password.I can still log in via Radius SSH with no problems and access privilege mode via SSH.What am I missing so we can have two different users be able to log in locally with different credentials and access privileged mode, and keep my ssh radius working?
View 3 Replies
View Related
Feb 9, 2013
When i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies
View Related
May 7, 2012
I have a Cisco 1841 router connected to two different lines (same ISP) and I would like to load balance between them. I think I have achieved this point, but the problem is that remote VPNs do not work (only from Dialer1).This is my diagram:
ISP1----ISP Router----------Fa0/1 ROUTER 1841
----------Fa0/0 LAN
ISP2 ----------------pppoe Dialer1 ROUTER 1841
I have tried to redirect all my vpn traffic through the Dialer1 with PBR, but it does not work.
View 4 Replies
View Related
Dec 11, 2011
Almost every sunday L3 switch reboot and give following error message.
View 2 Replies
View Related
Nov 16, 2009
I'm seeing the following error on a 4500 running 12.2(46)SG
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
I've attached a txt file with the show power detail output.
View 2 Replies
View Related
Feb 15, 2012
We are facing issue of having minor error for SUP module details below,SUP: WS-X45-SUP6-E see the minor error coming while troubleshooting this SUP 6-E error as below,
module 3: SerialNo :
Overall diagnostic result: MINOR ERROR#
Test results: (. = Pass, F = Fail, U = Untested)
1) supervisor-bootup ---------------> U
2) linecard-online-diag ------------> F
View 5 Replies
View Related
Mar 13, 2013
My cisco 4948 switch is generating the below error,how do i troubleshoot this error.
*Mar 13 00:09:33.451: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 14 times)Packet received with invalid source MAC addre ss (00:00:00:00:00:00) on port Gi1/37 in vlan 1Gi1/37- to this port another 2950 switch is connected by trunk link.and to this switch end host is connected i.e.thin client
View 3 Replies
View Related
Sep 20, 2012
The line card WS-X6724-SFP inserted in slot 2 is getting MINOR ERROR. I could also see TestTransceiverIntegrity: on port no 2/11 has failed.
Is this a h/w issue?
==================================================================================================
S/w model : WS-C6509-E
IOS : s72033-adventerprisek9_wan-mz.122-33.SXI3.bin
==================================================================================================
1) TestTransceiverIntegrity:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . F . . . . . . . . . . . U .
View 2 Replies
View Related
Apr 9, 2012
I have just moved to the 3750X switch and have connected it to a 6509E. From the beginning I was having OSPF encryption errors, followed by flood warnings, LSA issue's, duplicate IP's which is baffling me.
There are no IP's which match on either switch however the 3750X was continually power recycling causing the interfaces drop continually.Even after disconnecting from the 6509 the 3750X continue to behave in the same manner. Could there be some issue with this switch?
View 6 Replies
View Related
Feb 3, 2012
%SYSTEM_CONTROLLER-SP-3-ERROR: Error condition detected: TM_DATA_PARITY_ERROR Feb 2 10:57:09.602 EST: %SYSTEM_CONTROLLER-SP-3-EXCESSIVE_RESET: System Controller is getting reset so frequently
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF15a, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 20-Oct-08 19:20 by kellythw
Image text-base: 0x40101040, data-base: 0x42951080
[code]....
View 1 Replies
View Related
Mar 22, 2013
I have a PS3 connected to a Gig port on my 3560. When I boot-up the PS3 I have to wait around 30 seconds for it to get DHCP.
I noticed the orange LED would stay on and go green after 30 seconds. I assumed I would have an error-state but I do not, the port show connected with no errors even though it's orange. I have no connectivity from the ps3 until the light goes green and then all is well. The port is access and I have manually configured duplex and speed.
Switch>show version
Cisco IOS Software, C3560C Software (C3560c405ex-UNIVERSALK9-M), Version 12.2(55)EX3, RELEASE SOFTWARE (fc2)
[Code].....
View 5 Replies
View Related
May 13, 2013
I have 4507 switch and I got the error of fan sensor which is mention below [code] What the meaning of FAN Sensor both are Bad/off ?
View 4 Replies
View Related
Jan 2, 2008
I have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
An error appear in console (many times in one minute):
Jan 3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
What is the problem? What is the solution?
View 2 Replies
View Related
Jul 16, 2012
Getting a lot of the following errors on our 5508 form the same subnet: 10.20.0.1 255.255.248.0 . I tried researching and not getting much.
broffu_SocketReceive: Jul 17 10:11:10.068: %DATAPLANE-3-DP_MSG: broffu_fp_dapi_cmd.c:2891 FP0.09:(7089389)[cmdAddIpv4:2921]failed to find ipv4 10.20.6.58
[code]....
View 2 Replies
View Related
Feb 3, 2012
: %DATACORRUPTION-1-DATAINCONSISTENCY: unterminated string in buffer of length 129, counted: 129 -Traceback= 4027CB2C 402B1E88 4052884C 40528A48 40528D08 40529188 40529358 403247E8 403247D4
Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-ISV-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 19:41 by pwade
Image text-base: 0x40010948, data-base: 0x410F41D0
[code]....
View 6 Replies
View Related
Jun 25, 2012
I have port on cisco 3560 goes to error-disable,what is the cause of this issue,pls be noted this interface has BPDU Guard enable
View 3 Replies
View Related
May 8, 2011
I've taken 2 4507's fresh out of the box running CAT4500E-ENTSERVICESK9-MZ.122-53.SG2.BIN which was upgraded from CAT4500E-IPBASEK9-MZ.122-53.SG2.BIN
I'm getting constant %C4K_S2W-4-WRITECALENDARERR: Calendar write operation Failed errors on the console. I was also getting them on the original IOS version.
Anything I've seen say's to ignore them but their very frequent filling up the logs.
There's very little return on google and no bugs to report on Cisco?
View 8 Replies
View Related
Mar 5, 2010
This is a 6509 with Sup-2/MSFC2. Can't find any reference to this error on the cisco web site.
View 2 Replies
View Related
Apr 4, 2011
We're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
View 1 Replies
View Related
Nov 8, 2011
I have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies
View Related
Nov 11, 2012
I'm facing a problem where certain port on my swtich keep grant and remove poe.
Nov 12 07:02:43.639: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/18: Power granted
Nov 12 07:02:44.399: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/18: PD removed
[Code].....
View 2 Replies
View Related
Mar 2, 2012
on IOS versions higher than 12.2(50) on Cisco 3560G-48TS I get this error/traceback, when I reach a certain number of Access-lists group'ed to "interface vlan", and the ACL inserted in the TCAM reaches acl label #128 (can be seen with : Show platform acl label 128)I can see errors in the TCAM if I issue the command
View 21 Replies
View Related
Nov 3, 2011
I have a cisco 3745 router ,It has been working OK till this morning when it failed to boot this is the error that i get:
%ERR-1-GT64120 (PCI-0): Fatal error, CPU out of range error
GT=0x24000000, cause=0x0900E083, mask=0x0ED01F00, real_cause=0x08000000
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
bus_err_high=0x00000000, bus_err_low=0x083259C0, addr_decode_err=0x00000470
r0 = FFFFFFFF r1 = FFFFFFFF r2 = 0 r3 = 658A0000 r4 = 0
r5 = 1 r6 = 0 r7 = 0 r8 = 0 r9 = 4ECAB4A0
r10 = 0 r11 = 200 r12 = 0 r13 = 668BDF84 r14 = 0
[code]....
System returned to ROM by error - a System Error, PC 0x607DD5C0 at 11:06:37 ARG Fri Jun 15 2012 System image file is "flash:c3745-adventerprisek9_ivs-mz.124-15.T5.bin" Possible RAM fault?? not performed any modification.
View 1 Replies
View Related
Sep 4, 2012
I encountered problem while trying to copy file from Nexus 5548 to my ftp server (proteus - 192.168.12.220 - the Nexus switch is able to resolve name proteus correctly to 192.168.12.220). See below the working and not working scenarios. I have serached through Cisco Bug Database but unable to find any related bug associated to this problem. This Nexus is running the following NX-OS version.
n5000-uk9-kickstart.5.1.3.N1.1a.bin
n5000-uk9.5.1.3.N1.1a.bin
Working (without specifying the username and full path)
[Code].....
View 1 Replies
View Related
