Cisco Switching/Routing :: 3750X Duplicate IP Error
Apr 9, 2012
I have just moved to the 3750X switch and have connected it to a 6509E. From the beginning I was having OSPF encryption errors, followed by flood warnings, LSA issue's, duplicate IP's which is baffling me.
There are no IP's which match on either switch however the 3750X was continually power recycling causing the interfaces drop continually.Even after disconnecting from the 6509 the 3750X continue to behave in the same manner. Could there be some issue with this switch?
I've run in to this on 3750G's in a various sized stacks. We apply port security for a mac address on a single port (not existing on more than one port - that's a different issue that appears in multiple posts already).In this case:
1) We do a 'sho mac address-table and see that the device with the mac address in question lives on one port, port 1/0/x.
2) We apply mac port security for this exact same mac address to the same port it is already attached to. switch(config)#int g2/0/2 switch(config-if)#switchport port-security mac-address 001a.1ec8.abcd
3) Get this error: 'Found duplicate mac-address 001a.1ec8.abcd'.We again confirm that that is the only port on the entire switch that has this mac-address.Try the command again, same error.
4) We do a bunch of show commands, get in and out of the switch, go back and then try it again, and now it works, same command, same port and same mac address.
-Aging is default 300 -These are Cisco wireless AP's attached to the switch -This occurs on different switches with different ports using different mac addresses, always same symptoms.
I have two 3750Xs for stack, and i want connect a 2960 switch on this stack with port-channel.I connect 2960 G0/1 to 3750X G1/0/24, and 2960 G0/2 to 3750X G2/0/24. [code] i try to config spanning-tree etherchannel guard misconfig, but no use finally, i have to use "no errdisable detect cause all"..i check the cisco.com, and find a information: for this case, channel-group can use mode desirble.but when i try to change the channel-group in 3750X stack, it shows me that: "with pagp enable, desirble mode must config in the same switch".i try to use mode desirble mode in G1/0/23 and G1/0/24 in 3750X stack, it still can not work.i want to know how to solve this problem? not only do "no errdisable detect cause all".
I have a duplicate router ID problem that is confusing to me. A 6509 and 4510 swich both show the same router ID, but only the 6500 has the router ID IP address configured in it. We are running EIGPR. The 6509 has L0 as 164.72.239.1 configured, which is it's router ID. The 4510 doesn't have 164.72.239.1 configured on it, yet that's what it's router ID is. Below are a few show commands displaying this - and as you can see from the 'show run | include 239' from the 4510 there is no 164.72.239.1 configured on it:
6509 chassis
interface Loopback0ip address 164.72.239.1 255.255.255.255end RS6509-Core-A#sh ip eigrp topIP-EIGRP Topology Table for AS(1)/ID(164.72.239.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s -
[Code].....
why the 4510 has that router ID?
I know I can configure a different router ID on the 4510, but I'm curious as to why it is the way it is.
I have two 2960's in this new environment that I am administering. I am receiving a message on one unit (Designate it 2960-2) of %IP-4-DUPADDR: Duplicate address 192.168.168.8 on Vlan1, sourced by 3037.a63e.540. The "sourced by" address is the 2960-1. I do not know how these units were originally set up. How can I determine where the duplicate address is originating from.When I perform an ARP -a the address that corresponds to the 192.168.168.8 is the mac address of the ethersvi interface on the 2960-1. I
In NX-OS release 4.2(8) a feature was introduced to supress duplicate IP address warning messages in DCI environments.When using the same HSRP addresses in both DCs but blocking the HSRP exchange, ARP still detects these duplicate configuration and writes log messages. There obviously is a feature to suppress this but I do not find any reference how to enable it.url...
Recently I had came across 1 issue where one of the server IP had conflicted with VIP of Nexus core switch. The blade server was physically connected to Nexus Distribution switch which in turn connects to Nexus core. Neither Nexus core nor distribution had generate any logs in regards to IP conflict which ideally happens on Cisco catalyst switches. I haven't find any document on cisco as well as on internet for this issue . I dont know what logging need to enable on Nexus for this specific case . There are different logging levels define for every feature like hsrp, ip,monitor etc...
We have Nexus 7k with latest release 4.2(6) Software BIOS: version 3.22.0 kickstart: version 4.2(6) system: version 4.2(6)
I have a WLC 2504 with 5 AP licenses for which I have installed an adder license via GUI. The installation completed successfully, but I still cannot view the new license. The maximum number of APs is still showing as 5 and in fact I cannot add more that 5 APs. I tried installing the license file again, but now I get a "duplicate" error.
I am experiencing inconsistent echo-replay from devices connected via VPC to Nexus 5500s while pinging from the Nexus exec prompt.
In some cases I receive normal response when pinging from one Nexus, but no response when pinging from the other switch. In other instance I receive normal response to one Nexus, and duplicate replays to the other. It looks like a VPC related bug. NXOS is 5.1.3.N2.1
5501# ping 10.12.12.232 PING 10.12.12.232 (10.12.12.232): 56 data bytes 64 bytes from 10.12.12.232: icmp_seq=0 ttl=253 time=8.585 ms 64 bytes from 10.12.12.232: icmp_seq=0 ttl=254 time=9.227 ms (DUP!) 64 bytes from 10.12.12.232: icmp_seq=1 ttl=253 time=1.011 ms 64 bytes from 10.12.12.232: icmp_seq=2 ttl=253 time=8.097 ms 64 bytes from 10.12.12.232: icmp_seq=2 ttl=254 time=9.429 ms (DUP!) 64 bytes from 10.12.12.232: icmp_seq=3 ttl=253 time=18.195 ms 64 bytes from 10.12.12.232: icmp_seq=4 ttl=253 time=8.807 ms(code)
I have created 5 new 2 Gig port channels on a 6513 WS-X6516A-GBIC blade connecting to 5 4510R+E switches. 3 of the 5 Port-channels show up/up. 2 show down/down. However, for the 2 showing down, a duplicate Po interface was created with an "A" appended to the name that shows up/up. E.g:
Port-channel26 unassigned YES unset down down Port-channel26A unassigned YES unset up up
Each of the 4510s has a second 2Gig PO to another 6513 with an identical config and all of those come up fine.
I have some question about HSRP in 3750 switch. I have two Cisco 3750 switch which configured HSRP. Let say, we have interface vlan 100 that join in HSRP group member 1. The configuration on both switch is like as follows :
If I monitor a trunkport on the rootbridge in both directions I get Duplicate Multicast Packets on the perticular VLAN. The first guess is, that this is worked as designed and not a IOS Bug (Platform CAT6500 SUP720 IOS 12.2(33)SXI9 ) Until know I only found an old Cisco press link from 2002 with this subject.
We had a core switch (4503), distribution switches and access in our network and consists of many vlans. Almost all vlans uses DHCP Pools. But for few vlans DHCP is not yet configured. Recently one of the rogue user in vlan 1 gave the corresponding interface vlan ip of core switch (gateway) as his ip and caused a prolonged network outage for the vlan. Any way we are going to seggregate vlan 1 into different vlans, but before that we need a temporary plan to block such kinds of attack.What are the possible ways we can avoid the network outage problem even if a user gave the gateway ip to the machine?
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1 FastEthernet0/1 is up, line protocol is up Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE) 6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4 For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
i cant find any difference in these two devices when i am trying to compare throughput.I need upgrade our new POP and there will be around 4900 MAC adresses in VLAN 150 and 130 MAC adresses in vlan 200.Uplink is 1 gig routed internet connection and there is 14 downlinks to separate villages.i found a few differences for eg stack interface on 3750x but i dont need it.
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
I have an 1811 with several subnets connected to it.I recently installed a 3750x plant and want to bring my interior routing back to it.
All the routing is handled by the 1811 via secondary interfaces on vlan1?
I have 192 ports, and subnets show up on almost all of them. None of the ports are assigned to any specific vlans. Most ports have several subnets on them.
What is the best approach to getting the 3750x to handle the routing?
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
I am setting up a vm environment for a customer in my lab off site. I have two stacked 3750-x switches, a san, and threes UCS c220 M3S servers for hosts. I am trying to separate the lan traffic, san iscsi traffic, and san management traffic using vlans. The problem is i'm unable to communicate cross vlan with my current config, which I have attached to this post. The only noteworthy things in my conifg is that the ip route 0.0.0.0 0.0.0.0 192.168.83.6 is referring to a switch stack they have on site, that I will connect this stack to using the first two trunk ports on each switch, that I do not have here in the lab. I don't want to cause any confusion in why I have things set a certain way.
Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
I want to confirm this is a licensing issue. On a 3750X with ipbase, I cannot create a vrf. So I would need the universal image, and that is a seperate license, correct?Is there a link that describes the difference bewteen ipbase and univeral images?
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
There seems to be a lot of conflicting information on what can and can't stack together in the 3750X range.
I know that LAN Base can only stack with other LAN Base switches.
Can IP Base stack with IP services in 3750X? I have also heard that the 15.x.x IOS restricts mixed feature set stacks?
I know that Cisco recommends that all switches in a stack have the same IOS and feature set but having all IP Services in a stack can get too expensive.
I'm trying to review a QoS setup, and I'd like to make sure I fully understand the current setup before I change anything. I'm seeing output drops on two different queue-thresholds, but not sure how packets are making it to one of the queues.
Switch Version CORE#show ver Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(2)SE, RELEASE SOFTWARE (fc1) System image file is "flash:/c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin" cisco WS-C3750X-24 (PowerPC405) processor (revision A0) with 262144K bytes of memory. Switch Ports Model SW Version(code)
I can find queue4-threshold3 in the mappings, but how are packets getting mapped to queue2-threshold1? The priority queue is disabled for this interface, so I'm not sure how this queue is dropping packets, according to the maps nothing is mapped to 02-01.
I am building a switch stack using 4 48 port 3750X switches that will also have the power stacked. If I install a single 715W power supply in each switch will the stack support 802.3af accross all 48 ports on each switch? My calculations are 48 ports x 15.4W which gives me almost 740W needed which is over hte 715W power supply. I was reading somewhere were it mentioned that in a powerstack additional power can be drawn from the stack. I know this will not work if you are trying to support power on all switches accross all ports but would it if say 2 of the 4 switches are needing to provide PoE accross all 48 ports? If I say we can only use 24 ports per switch for PoE that drops the power need down to 370W which I believe should work. Just trying to get a better understanding of PoE consumption. Would the best solution be to just add a second power supply to each switch?
I have a switch which is rebooting it self, we bought it a year back,its a new switch, i did not find any error on sh ver after rebooting. I am using OP manager, i did not receive any alerts. I have done all diagnostic test, all are passed, i did not find any problem..
I am having an odd issue on a couple of new 3750X switches.I am trying to configure VRF-lite and it is not recoginizing the command.Does that make any sense? I have goggled the syntax ans it should be right.
